Search Documents

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By George S. Rice

"""To prevent the propagation of mine explosions, the Bureau of Mines, Department of Commerce, recommends rock-dusting all coal mines, except anthracite mines, in every part, whether in damp or dry condition. It also recom¬mends that rock-dust barriers be used to sectionalize the mine as additional defense; but these should not be regarded as a substitute for generalized rock-dusting."" (Mine safety decision, No. 5, April 7, 1927.)The purposes of this circular are to present concisely the requirements for effective rock-dusting of coal mines in order to prevent propagation of mine explosions, and to point out the principal related facts on explosibility of coal dusts and mixed coal-mine dusts, as determined by extensive testing in the Experimental Mine of the Bureau of Mines. study of these principal facts on coal-dust explosibility in conjunction with the recommendations for rock-dusting, should help to make clear to mine operators and others concerned the necessity for systematic rock-dusting in all coal mines except anthracite mines, and the futility of inadequate or sporadic rock dusting.The descriptions of nearly 1000 explosion tests in the Experimental Mine are available in a forth-coming bulletin2 and in earlier publications.3For detailed specifications as to the kind of rock-dust, amount to use, where to be applied, and method of sampling and testing, the reader is referred to Bureau of Mines Serial 26064, and American Engineering Standard Committee ""Recommended American Practice for Rock-Dusting Coal Mines"" quoted in Bureau of Mines Information Circular No. 60305.Summary of Specifications for Rock-Dusting1. Mines to be rock-dustedAll coal mines, except anthracite mines, should be rock-dusted.2. Extent of rock-dustingAll open accessible parts of a coal mine should be rock-dusted, including slopes, entries, cross,-cuts, and rooms, headings and pillar workings to within at least 50 feet of the face.3 Amount of rock-dustingAfter cleaning up the coal dust as thoroughly as practicable, sufficient rock-dust should be used to have the mixture of remaining coal-dust plus the rock-dust in any zone contain 65 per cent or more of inert or noncombustible matter. First dusting may require 3 pounds to 5 pounds per linear foot of passageway.4. When to rock-dust In any zone or section (made by dividing the mine for rock-dusting purposes) when the incombustible content falls to 55 per cent, that section should be re-rock-dusted so as to bring the incombustible content well above 65 per cent."

Jun 1, 1927

By James R. Cosby

This report describes work performed for the Bureau of Mines to evaluate available portable instruments for their effectiveness in detecting and locating damaged metallic shields in Types SHD and SHC cables. A second phase of the program is also covered wherein several instruments of a type which show promise are purchased for modification and testing to verify their performance.

Jan 1, 1980

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By Thomas Jenning, C. M. Keithly

"INTRODUCTION This report is one of a series. 4. 5. 6/ concerned with presenting historical development, and operating data on secondary-recovery projects in various States to stimulate interest in sound secondary-recovery programs. Preceding reports in this series have dealt exclusively with descriptions of and results obtained by water flooding in three states, but no recent publication of comparable purpose describes gas-injection 7/ practices. The authors intend to present material relevant to the development and operation of gas-injection projects in Illinois, with particular emphasis on those producing from oil-bearing horizons that had been depleted to a point near the economic limit of operation by past oil-recovery methods.Most operators realize that the energy expended on the movement of fluids through gas-expansion- or gas-cap-type oil reservoirs to producing wells must be supplemented to attain maximum recovery of the oil present. Under favorable conditions, many operators choose to maintain oil-propulsive forces at or near their original magnitude by injecting extraneous fluids into a reservoir or recycling produced fluids early in the life of a field. More common, and less desirable, is the practice of replenishing these forces after primary producing methods become unprofitable. The lattes practice has been adopted in many stripper fields in Illinois and most of the oil-producing States during the last 40 years, but other old oil fields, and oil properties within those fields which were partly exploited by secondary--recovery methods, also may offer favorable opportunity for further development. To encourage and, aid operators in the development of gas-injection projects in the old oil fields of the United States, four projects have been described in detail in this report."

Nov 1, 1944

By W. R. K. Wu

Results of linear correlations of two to four variables by the least-squares method are presented. The variables include 63 parameters representing coal composition, coal plasticity, and coke strength. The composition parameters are on chemical analyses; the plasticity parameters, on three plastometer and dilatometer tests and four miscellaneous tests; and the coke-strength parameters, on three ASTM indices. Seventy-two to eighty-four plastic coals were used in the plasticity and carbonization tests, which together form the basis of this report; 43 nonplastic or weakly plastic coals were used in the coal-band studies. Plots of relations between volatile matter, carbon, and oxygen contents of 1,860 U.S. coals and the 84 coals used are shown. Similar plots between volatile matter and hydrogen or atomic H/C of the 84 coals are also included. Significances of regression coefficient signs for coal composition parameters in the significant correlations found are discussed. Based on these significances, the following relations are shown: (a) coke strength versus average aromaticity, or mineral matter content, of the parent coal; (b) characteristic temperatures of the plastometer and dilatometers, the free-swelling index, or the Gray-King type versus average hydroaromaticity of the coal; and (c) nontemperature parameters of the plastometer and dilatometers versus the physical properties of a certain group of compounds from thermal decomposition of coal. Similarly, significances between the positions of coals in the coal band and the aforementioned relations are also discussed. A structural theory of coal plasticity is proposed. Applications of the correlation results are discussed. Composition parameters, such as carbon, atomic H/C, and calorific value may be used as a basis for selecting coking coals for stronger coke. Plasticity parameters, such as the end temperatures of the plastometer and dilatometers and the free-swelling index, may be used for the same purpose. Based on the best correlations found, coke-strength indices may be estimated to within 4 to 8 units of the observed values; the end temperatures of the plastometer and dilatometer tests, 5° to 10° C.; and the free-swelling index, within 1 unit. Accuracies of all these estimated values are examined, based on the experimental errors of the data involved. Finally, estimations of plasticity parameters from one test with those from others are shown.

Jan 1, 1971

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By A. L. Murray, P. A. Surgeon

The Spring Canyon Mine Rescue Association is a cooperative association supported jointly by five coal-mining companies located in Spring Canyon, Utah. The properties of mining companies the Carbon Fuel Co, Rains , Utah, the Liberty Coal Co. , Latuda, Utah, the Standard Coal Co. , Standardville , Utan, the Spring Canyon Coal Co. , Storrs , Utah, and the Peerless Coal Co. , Peerless , Utah about a mile apart and normally employ a total of 915 men , 733 underground 182 on the surface . and The Association was organized on July 5, 1921 , and Rudolph Clark, fomerly first - aid miner on U. S. Bureau of Mines Rescue Car 11 , was placed in charge. as manager . A board of directors made up of a representative from each of the cooperating companies (usually the mine superintendent ) is the governing body of the Association and the expenses are prorated on a basis of the production of each of the five mines . The Association maintains eight sets of Gibbs rescue apparatus and a motor truck fitted up as a combined rescue truck and ambulance . Additional apparatus are to be purchased . Standardville is the central camp in the canyon and has been made the headquarters of the Association . The apparatus are now kept and the truck housed in a small station, but plans have been prepared for a large station which will be built this summer . This new station will have a large apparatus room , a test chamber, a suitable room. for training, and a garage on the first floor, while above will be the living quarters of the manager . There is a good road through the canyon and the other camps are all within two and one -half miles of Standardville .

May 1, 1922

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By A. C. Fieldner

"INTRODUCTION In a previous report3 prepared for the American Gas Association, the influence of washing coal on coke properties and on gas and by-product yields was discussed on the basis of answers to questionnaires sent to coke-oven superintendents and a review of the literature on the subject. This review indicated that the elimination of free impurities by cleaning coal improved coke quality by (a) reducing ash and sulphur, (b) decreasing clinker trouble in burning the coke, (c) diminishing cross fractures in the coke, resulting in greater resistance to breakage on handling, and less small coke and breeze, and (d) greater uniformity in chemical composition and physical properties of coke. Washing also reduced the sulphur in coke and gas and increased the yield of gas and by-products per ton of dry coal charged.This paper is supplementary to the previous report and presents some experimental data obtained with Pittsburgh bed coal from Pennsylvania and Mary Lee bed coal from Alabama.ACKNOWLEDGMENTSGrateful acknowledgment is made to F. J. Pfluke, of the Rochester Gas and Electric Cc., of Rochester, N. Y., for the plant test data on screened lump and washed coal; and to Ray W. Arms, Manager of the Coal Cleaning Department, of Roberts & Schaefer Co., of Chicago, for the data on effect of air cleaning."

May 1, 1931

By E. D. Eastman

There are three researches upon the specific heat of water vapor by the method of explosion that are sufficiently advanced in technique and suitable in plan to justify careful study of their results , with the double purpose of fixing the best available experimental values and indicating the attainable accuracy of the method. These three researches comprise the work of Pier , Bjerrum , and Siegel.5 The work of earlier date than Pier's suffers from obvious inaccuracy of measurement , while the experiments more recent than Siegel's , such as those of Womersley6 , of Bone and his collaborators , and of Maxwell and Wheeler , 8 are for the most part not well designed for the accurate determination of the heat capacities in question . Some of the errors to which they are especially subject have been discussed by David and by David and Thorp.

Sep 1, 1930

By Gabriel S. Esterhuizen, Jarek Jakubec

In 2000, Laubscher’s Mining Rock Mass Rating (MRMR) classification system was updated and published. The new system brought a few fundamental changes that were in direct response to the challenges and problems encountered when applying the classification system in the mining environment, specifically caving operations. The fundamental changes introduced into the MRMR system in 2000 were the abandonment of the Rock Quality Designation (RQD) as an input parameter, accounting for healed and cemented joints, and the concept of rock block strength. The objective of this paper is not to discuss the role and usefulness of classification systems; the fact that classification systems are widely used in every stage of mining projects speaks for itself. This paper discusses some of the experiences gained with the MRMR 2000 system in various mining projects and shows how the changes to the system have resulted in improved assessment of rock mass conditions. Issues related to core logging for rock mass assessment are also presented.

Jan 5, 2007

By Dennis J. Grigal

The goal of the program is to develop a dust collector system mounted on a ranging drum or arm shearer which will: 1) reduce the respirable dust level of the shearer operator by at least 75 percent; 2) be easily and economically mounted on an existing shearer; and 3) will not, through modifications to the shearer, reduce its safety or productive capability. The development program consists of three phases covering the activities of the design of the dust collector system, fabricating and installing it on the ranging arm or drum shearer, and conducting underground field tests on the modified mining machine.

Jan 1, 1980

Mineral production was of little significance in the country's economy, and Bangladesh was not a world-ranked producer of any mineral commodity during 1977. Natural gas was the most important mineral exploited; however, reserves were sufficient to allow for much greater production, Economically, Bangladesh made some progress in 1977-782 in its struggle against poverty, underdevelopment, and rapidly increasing population. The gross domestic product (GDP) grew 8%, mainly owing to a 13% increase in food grain production, the key economic indicator in this highly agricultural nation. GDP at current prices dropped slightly in Fiscal Year (FY) 1976.77 to $6.6 billion3 and rose to $7.2 billion in FY 1977.78. The population rose from 81 million in FY 1975-76 to about 85 million in FY 1977-78, resulting in an increase of per capita GDP from $83 to $85 during the same period. The high annual population growth rate, over 3% in 1976 and about 2.8% in 1977, was recognized by the Government as the main problem facing the country. Average density was 525 people per square kilometer. A similar density would have the entire world population living within the continental United States.

Jan 1, 1981

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By Todd M. Ruff

This report summarizes ongoing research at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, in which collision warning systems for surface mining dump trucks are being evaluated. Common accidents involve these large trucks running over smaller vehicles or pedestrian workers. Collision warning systems currently use one of several methods, including radar, radio-frequency-signal detection, or ultrasonic signals, to detect and warn of the presence of an object or person in the blind spots of the mining equipment. Most available systems have not been tested on large off-highway dump trucks. This report evaluates several systems on two sizes of trucks, a 50-ton-capacity truck commonly used in quarries and construction and a 240-ton-capacity truck commonly used in open-pit mines. Tests were conducted to determine false alarm rates, alarm effectiveness, and reliable detection zones for a person and a pickup truck. The results indicate that radar and radio-frequency identification systems show promise for this application and that several of the improved systems are ready for extensive field tests. However, challenges still exist in applying these technologies to large trucks.

Jan 11, 2000

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930

By W. W. Scott

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the entire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 1, 1974