Search Documents

By D. R. Tweeton

The U.S. Bureau of Mines, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geo- physical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency- domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted before and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.

Jan 1, 2010

By W. W. Adams

Every man-hour of work performed in and about the coal mines of the United States had a 2-percent heavier death load from accidents in 1938 than in 1937. This is an unorthodox way of stating that the death rate per million man-hours of exposure or employment was 2 percent higher in 1938 than in 1937, increasing from 1.74 to 1.78. Thus the average miner had a 2-percent greater chance of being killed in 1938 than he had in 1937. The average quantity of coal resulting from 1 man-hour of work increased 3.6 percent -from 0.615 ton in 1937 to 0.637 ton in 1938. The production of the average ton of coal was accompanied by a slightly smaller loss of life in 1938 than in 1937, the accident rate being 2.793 per million tons in 1938 compared with 2.833 in 1937.

Jan 1, 1941

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in nongassy noncoal mines and tunnels. This revised and supplemented listing supersedes an earlier publication2 released in 1963. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and outlined in the Bureau's permissible schedules before the Bureau approves it for safe use in mines.

Jan 1, 1968

By Fred N. Kissell

Air recirculation caused by dust scrubbers at coal mine working faces was examined by the Federal Bureau of Mines with regard to the potential hazards caused by a possible buildup of methane gas. A theoretical analysis indicated that there was no apriori way to predict the effect of scrubber recirculation on methane concentration levels. Experiments conducted in a full-scale model of a working face area indicated that methane levels were dependent to a great extent on the location of the scrubber exhaust, but that the scrubber recirculation did not substantially increase the methane concentration above those levels that would have prevailed were the scrubber not in operation. An analysis of two underground scrubber trials showed that the scrubbers had no significant effect on methane levels, and a review of explosions attributed to recirculation showed that these were characterized by a lack of fresh air as well as recirculation. It was concluded that high methane levels are due more to a lack of fresh air than to recirculation.

Jan 1, 1975

By Christopher Mark

This proceedings volume contains papers presented at technology transfer seminars sponsored by the National Institute for Occupational Safety and Health (NIOSH) on New Technology for Ground Control in Retreat Mining. The seminars were conducted at five locations: Uniontown, PA (March 26, 1997), Norton, VA (April 8, 1997), Pikeville, KY (April 10, 1997), Charleston, WV (April 17, 1997), and Evansville, IN (April 22, 1997). The papers presented here describe several new, highly practical technologies developed by the NIOSH Pittsburgh and Spokane Research Centers3 to improve safety during pillar retreat operations. Two central issues are addressed: pillar design and mobile roof supports (MRS's). Proper pillar sizing is essential for safe pillar extraction. The Analysis of Retreat Mining Pillar Stability (ARMPS) program and its large data base of actual mining case histories are presented. LAMODEL, a second computer program, can be used for analysis of multiple-seam and other complex mining situations. Other papers address pillar design to avoid massive pillar collapses and the proper role of coal strength testing. MRS's have greatly improved safety where they are used for pillar line support. We studied the application of MRS's at 20 mines throughout the Eastern United States. Conclusions regarding the most effective section layouts, cut sequences, and support placements are reported. Field and laboratory tests of MRS's are also described.

Jan 1, 1997

By H. Britton

This bulletin is the seventh in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, 216, and 220 being compilations for the years 1915, 1916, 1917, 1918, 1919-20, and 1921, respectively. In this bulletin the same general plan of classification of references has been followed, but several additions have been made. ACKNOWLEDGMENTS Acknowledgment is made to the following organizations for the use of their libraries in the preparation of this bulletin: University of California, Stanford University, California State Mining Bureau, Union Oil Co. of California, Standard Oil Co. of California, and the Mechanics Mercantile Library of San Francisco; acknowledgment for their assistance is also made to H. H. Hill, C. P. Bowie, A. L. Foster, M. J. Gavin, H. C. Miller, E. B. Swanson, and Miss Louise Janssen, all of the Bureau of Mines, and to Miss Elizabeth H. Burroughs of the Union Oil Co. of California.

Jan 1, 1929

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By Michael Rieber

An analysis of coal slurry pipelines was presented in our May 1976 study, Route Specific Cost Comparisons: Unit Trains, Coal Slurry Pipelines and Extra High Voltage Transmission (4]. The present study extends that analysis. The earlier work included technical and economic cost descriptions of the black Mesa and ETSI pipelines as well as some hypothetical pipeline routes. Water problems, safety and environment, required resources, and labor impacts were discussed at some length. Additionally, pipeline impacts on competing railroads, slurry-rail comparisons, and cost escalation. were analyzed. The difference in pipeline profitability to an owner-operator versus a promoter-builder was suggested. These aspects are not redone in this study. Here, we present a synopsis of the previous results and a general statement of coal slurry pipelines. Extensions of the arguments are presented where they appear warranted. New material is developed in the area of pipeline branching and tapping. This would appear necessary if slurry pipelines are to function as more than private lines; if they are, for example, to be responsive to common carrier requirements.

Jan 1, 1977

By W. W. Graff

This paper describing the mining practice at Mine No. 5 of the Marquette range, Michigan, is one of a series being prepared by the Bureau of Mines on mining practices, methods, tend costs in the various mining districts of the United States. The top-slicing system of mining, has been used ever since the present operating company took control of the property in 1903, the main level and sublevel layout being chanced only as local conditions required and the use of mechanical equipment increased.

Jan 1, 1930

By G. E. McElroy

As one phase of a general program of enthracite mine-fire research initiated by the Bureau of Mines in September 1935, a study of the records of past fires was considered a necessary approach to a proper understanding of present and future fires because only limited information could be obtained directly from existing active fires on account of their inaccessibility. Through the courtesy of interested operators, all available records of fires that had occurred in a large group of steep-pitch anthracite mines in the Western Middle and Southern fields of the Pennsylvania anthracite district were examined and analyzed for data on the causes, costs, behavior, and control of fires, and this report is primarily a discussion of these factors based on a close study of these particular records. Mining Conditions The records pertain to a group of mines that have contributed about 12 percent of the total Pennsylvania anthracite production and constitute a large proportion of, and well represent, steep-pitch operations in this district. Throughout the area represented, the coal occurs as a series of up to 20 parallel seams in folded slate and sandstone strata and almost entirely on pitches of 400 to 80°, with vein thicknesses of 5 to 60 feet. Practically all are old mines with histories dating back to 1850, or thereabouts, and present operations are either under or adjacent to mined-out areas extending to surface or to the saddles of anticlines. All operations are at relatively shallow depths, that is, within 1,000 feet, vertically, of the surface. Mining methods are largely a heritage of the past and embrace typical breast and pillar operations with practically no mechanized mining and with the coal shot ?off the solid.? Most of the mines are rated as gassy and are operated now on a closed-light basis. Permissible explosives are now used entirely for breaking coal, and dynamites for rock work and chute-starting blasting.

Jan 1, 1938

By L. P. Purtell

The performance of ten anemometers of several types has been measured at low air speeds. Multiple calibration runs provided sufficient data for measuring random error about the mean calibration curve in addition to the difference between indicated and true speeds. Measurements were also performed of the minimum operating speeds of the anemometers.

Jan 1, 1979

By J. E. Hamak

This publication contains analyses and related source data for 162 natural gas samples from 15 states and 4 foreign countries. Of the total samples, 154 were collected during calendar year 1992. The remainder were collected earlier, but releases granting permission to publish were not received until 1992. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of U.S. Department of the Interior, U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free-market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1993

The United States is rapidly depleting many of its most important minerals and fuels. The first two Annual Reports by the Secretary of the Interior, under the Mining and Minerals Policy Act of 1970, made us acutely aware that the natural resources that enabled this Nation to attain an unprecedented growth in terms of economic well-being, and to set an example of independent strength through the democratic process, are finite. Once they are depleted, large imports will be required. Simultaneously, competition for available supplies, especially of petroleum, is increasing in the expanding European and Japanese industrial communities and in the underdeveloped nations of the world. Even before the crisis of late 1973, the oil-producing nations of the world, principally in the Middle East, but including Canada and Latin America, were recognizing that the worldwide need for crude oil, petroleum products, and natural gas could be translated into an unprecedented economic bargaining position. Thus, the members of the Organization of Petroleum Exporting Countries (OPEC) raised the price of their crude twice during the first 6 months of 1973. By yearend the energy situation had be-come acute, and it seemed probable that regardless of current political developments, the era of cheap energy was over.

Jan 1, 1973

The Bureau of Mines is active in programs pertaining to solid waste disposal and land reclamation. Nine reclamation projects of mining companies and six projects of the Commonwealth of Pennsylvania were investigated to provide information on the procedures, costs, and results obtained from reclamation projects of bituminous coal-waste disposal areas. Refuse disposal costs of mining companies ranged from 9 to 28 cents per ton-mile, and quantities disposed of ranged from 600 to 4,500 tons per day. Spreading and compacting the refuse at the dump site ranged from 3 to 20 cents per ton. Cost of covering with soil and planting ranged from $750 to $1,646 per acre. Total costs of reclamation for the Pennsylvania projects ranged from about $1,800 to more than $15,000 per acre. Refuse preparation costs ranged from $772 to $5,550 per acre. Soil covering and planting costs ranged from $1,083 to $5,086 per acre. The best results were obtained by soil preparation and conditioning prior to planting. The type and depth of soil and effect of climate were also factors.

Jan 1, 1973

By John F. McCoy

The U.S. Bureau of Mines (USBM) awarded? a contract to Foster-Miller, Inc. to develop guidelines for designing, constructing, stocking, and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressuriztion Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By C. F. McCarroll

The effectiveness of an industry's safety activities can be gaged best by the accident records of that industry. In an effort to gage conditions in the petroleum industry, and with the objective of helping to reduce the number of accidents in it, the Bureau of Mines from time to time has tabulated, analyzed, and published pertinent statistical information.3/. These reports have dealt with distribution, causes, and costs and related phases of accidents for various and collective divisions of the petroleum industry in several sections of the country. This type of study aids the personnel of the Bureau in planning the course of its activities in accident-prevention work and gives useful data to persons engaged or interested in the promotion of safety in the petroleum industry, which will aid them in their efforts to reduce the number and severity of accidents. A majority of petroleum operators and "service? contractors have acknowledged their responsibility to provide their employees with safe working conditions and to their stockholders for greater economic value of invested capital by establishing safety divisions within their respective organizations. Such divisions have a primary duty, namely, to see that properly designed and guarded machinery and working equipment are furnished the employees and that they are trained in the safest practical methods of performing their work. Some companies and individual operators, however, have shown little or

Jan 1, 1939

By R. D. Groves

Laboratory research has demonstrated that high - grade copper powders can be produced under controlled conditions from cement copper products . The technique should enable small producers to prepare a directly marketable product by means other than smelting and electrolytic purification . A continuous drum- type precipitator was the preferred unit for producing fine - sized particles of cement copper that were further processed by chemical digestion in a copper sulfate solution , by reduction and sintering in a hydrogen atmosphere , and by grinding to a powder . The effects of variables related to all stages of the process were investigated . Treatment of leach solutions from three different sources resulted in copper powders containing 99.2 to 99.8 pct Cu , apparent densities of 1.97 to 2.25 grams per cu cm , good powder flow rates , and a size distribution of 54.9 to 60.1 pct minus 325 - mesh material .

Jan 1, 1964

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the' Bureau of Mines since 1917. The analysis published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966