Search Documents

By R. C. Bates

Uranium mine workers? daily exposure to radon daughters was estimated by two methods of sampling, detailed and spot-check. Both methods involve time- weighting measured exposure levels to arrive at an average exposure figure. Random sampling, or sampling without regard for the duration of exposure, has proved inadequate for estimating average exposure levels. During the first phase of the study, the breathing zones of eight workmen in three underground uranium mines were sampled for an entire shift; 20 to 36 radon-daughter samples were collected per man-shift, Analysis of these data indicated that a suitably accurate estimate of the full-shift exposure could be made by time weighting a considerable lesser number of representative radon-daughter samples. This analysis led to the spot-check method of estimating full-shift exposures to radon daughters. Additional detailed studies were made in seven mines to Learn more about the full-shift radon-daughter exposures and to test the spot-check method, In all, 617 radon-daughter samples were taken in 10 underground uranium mines during 26 man-shifts, and the spot-check method was tested 35 times.

Jan 1, 1962

By F. F. Aplan

Separation of the slightly soluble minerals (Ksp? 10-10), one from the other is one of the more difficult tasks confronting flotation engineers. This study has focused on means of separating such prominent members of this class as scheelite, fluorite and calcite from one another. Some experimental work has also been done on the minerals magnesite, dolomite and apatite. Carboxylic acid-type collectors are commonly used industrially to float all of these minerals. Thus, the problem at hand is to ascertain means of achieving selectivity between minerals known to respond rather similarly in flotation. Four techniques have been proposed for the separation of minerals of this class from each other: 1. Control of potential determining ions 2. Use of stereo-specific collectors 3. Use of flotation rate differences 4. Use of selective activating and depressing compounds. This study was directed toward a cursory evaluation of each of these techniques, and each was found to be a possible method of achieving selectivity. Stereo-specific collectors -- those whose parking area may closely match the available adsorption site on one mineral but not on another -- are a possible means of achieving selectivity between scheelite, fluorite and calcite. Stereo-hindered carboxylic acid salts and sulfonates all show selectivity between the three minerals tested. Separations also appear to be possible by the controlled use of the lattice ions (e.g., Ca and [W0=4] for scheelite, CaW04), H+, [OH-, C0-3 and HCO=3]; all of them ostensibly potential determining in the systems studied. Flotation rate differences of the minerals as a function of pH under conditions of starvation collector usage also showed promise. Scheelite and fluorite float most rapidly with sodium oleate in slightly acidic (pH 4-7) solutions whereas calcite floats most rapidly near pH 10. Use of Mn++, Pb++, or other heavy metal hydroxy complexes as activators was seen to effect each of the slightly soluble minerals differently. This is in sharp contrast to the oxygen containing, relatively insoluble minerals, where all minerals respond in a similar manner to such activation procedures. Results indicate that all four methods outlined above may potentially be used to achieve flotation separation of the slightly soluble minerals. More extensive research should be undertaken to detail the spcific applicability of each of the procedures and to make a more complete evaluation of the effect of collector type and concentration, mineral type, pH and size effects.

Jan 1, 1983

By A. Visnapuu

The U.S. Bureau of Mines investigated the oxidation of American Iron and Steel Institute (AISI) Type 304 stainless steel (SS) during annealing in simulated combustion products from several air-CH4 fuel ratios. Atmospheres representing air-CH4 ratios of 14:1 and 18:1 contained free 02, while atmospheres representing 10:1 air-CH, ratio did not. A Cr203 layer formed on SS samples annealed in atmospheres containing free 0, while a Cr-Fe spinel layer formed in atmospheres with no free 02. The Cr203 layer was adherent and presented a protective barrier to metal diffusion, effectively limiting oxidation of the metal substrate. The Cr-Fe spinel was not protective and allowed the diffusion of Fe through the spinel to the gas-oxide interface where it was oxidized to magnetite, which spalled from the surface. This resulted in thick scale layers on samples annealed in atmospheres containing no free 02, as compared to layers formed on samples annealed in atmospheres containing free 02. These results confirmed and explained industrial operators' observations that thick, smoky (fine spalled magnetite) scales form on SS annealed in low free-02 atmospheres, while thin protective oxide layers form on sheets in atmospheres containing free 02.

Jan 1, 2010

By Ernest W. Johnson

Diamond, drilling of some blast holes in stoning operations is practised in at least two iron mines in the Lake Superior district - the Soudan mine of the Oliver Iron Mining Co., on the Vermilion range at Soudan, Minn., and the Anvil-Palms mine, operated by Pickands, Bather & Co., on the Gogebic range at Bessemer, Mich. Diamond drilling, at the Soudan nine has partly replaced percussion drilling because of the extreme hardness of the ore and of the lean formation. According to Wolff,4/ the jasper or lean formation in this mine is the hardest rock regularly drilled in any commercial operation.

Jan 1, 1945

By H. B. Brunot, L. C. IlsLey

The chief object of the Electrical Section of the United States Bureau of Mines is the study of causes and means of preventing accidents resulting from the use of electricity in mines . A large part of this work for the last 20 years has been the inspection and testing of mining equipment under the provisions of schedules which give the minimum requirements considered essential for the safety of equipment intended for use at or near the working faces of dusty or gassy mines . During the first few years of this work , particular attention was paid to the explosionproof features of the various accessories such as motors , controllers , and other parts . The knowledge of the essentials necessary for safe designs of enclosures has since been augmented by field experience and by data obtained in testing a large number and variety of designs . With our present knowledge it would seem that a disproportionate stress was placed on making the various enclosures explosionproof , but not enough thought was given to the danger from wiring and connections outside of explosionproof enclosures . The list of equipment that has met minimum requirements for safety and has been approved as permissible by the Bureau of Mines includes storage - battery locomotives , power trucks , drills , loading machines , conveyors , cutting machines , room hoists , pumps , concrete mixers , and rock-dusting machines . The wiring on some of the machines is comparatively simple and sometimes , except for the trailing cable , may be entirely within the explosionproof enclosures . In general , there is outside wiring between enclosures , and on the larger machines the wiring may be extensive and complicated . In considering the safety of wiring for mining machinery , attention must be given the severe service and unfavorable surroundings imposed by mining conditions . Some of the matters that require consideration are : ground . The lack of care of the exterior wiring to be expected in the average mine . The lack of adequate periodic inspection of the wiring . The absence of adequate facilities for satisfactory inspection and repairs under- The severe conditions of moisture , dirt , mechanical injury , and low voltage encountered in mining service .

Apr 1, 1931

By J. S. Dunning

The Bureau of Mines investigated a series of Fe-Al-Mo alloys strengthened by ZrC (zirconium carbide) precipitates as chromium-free substitutes for stainless steels. Melting and fabrication methods were devised, and the effects of minor additions of columbium (niobium) and cerium on the mechanical properties and oxidation resistance were determined. Zirconium carbides could not be con-trolled reliably to produce fine precipitate dispersions. A more reliable carbide strengthening mechanism is required if the high-temperature strengths of types 304 and 316 stainless steels are to be duplicated. Workability and oxidation resistance of the alloy series were excellent.

Jan 1, 1982

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By H. M. Smith

[ ]

Jan 1, 1927

By D. E. Wolfson

This report presents 900° C BM-AGA carbonization and related data for coals from the principal beds of Nicholas, Randolph, and Webster Counties, W. Va. Thirty-three samples from nine coal beds in three counties were car-bonized at 900° C in the l8-inch-diameter BM-AGA retort, data from which have been correlated with industrial production. Host of the samples were chemically suitable for metallurgical use, and their coking properties were satisfactory. Except for four of the Lower Kit-tanning samples, the ranges of constituents in the coal seams were 1.8 to 9.0 percent ash and 0.4 to 1.1 percent sulfur, values within the range of accept-ability for metallurgical coals. Coke strength indexes were normal for Appalachian coals of similar rank, and the tumbler stability indexes of the coke ranged from 35 to 57.

Jan 1, 1969

By R. L. Grayson, S. S. Peng

"Abstract. Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include:l. Respirable mass concentration, 2. Mineral composition,3. Particle size distribution by mineral,4. Particle shape distribution by mineral,5. Particle angularity distribution by mineral, and6. Respirable size distribution.Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.INTRODUCTIONThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from dangerous exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al. (1971) whi3h has been used to establish the 2mg/m exposure limit in the United States. According to the model, exposure to respirable dust for 35 years at this level or less would prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP). The exposure limit, of course, must be adjusted whenever greater than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mass concentration exposure, which showed the highest correlation with incidence and progression of CWP. As Morgan; et al. (1973) noted, howev.er, the quantity of respirable dust inhaled is not the only significant factor. It is noted that although mass of respirable dust correlates highest with the incidence of CWP, it is not a causal factor. Indeed, the insidious processes causing the disease occur on the cell-particle scale, requiring microscopic investigation."

Mar 1, 1989

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By P. C. Good

To meet a growing need for thorium metal of high purity and amenability to fabrication, the Bureau of Mines devised a method for preparing thorium metal by the reduction of thorium tetrachloride. Thorium tetrachloride was prepared by chlorinating calcined thorium oxalate with carbon tetrachloride. The crude thorium tetrachloride, containing oxygen-bearing compounds, was purified by a double vacuum distillation at 800 to 900° C., and thorium metal was made in the form of a dense sponge by the reaction of metallic sodium or magnesium with thorium tetrachloride at 800° C. Vacuum arc melting was used to consolidate the sponge metal to ingot form for evaluation of its physical and chemical properties.

Jan 1, 1960

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By Thomas C. Denton

ALL of the 45 political divisions of Africa were accessible to non-Communist world industry and commerce throughout 1964, although in some of them revolt and political attitudes presented problems. The position of the continent as a whole for mineral and mineral fuel resources, production, and oversea exports continued to improve. At yearend, significant quantities of a greater number of mineral commodities vital to industry and agriculture were being produced than in any other continent. This statement excludes Communist areas on other continents but might well hold true even if such areas were included. Deriving from its exceptionally diversified production, Africa furnished overseas industrialized countries as a w ole a greater variety of key mineral commodities than any other area. In addition, the value of mineral imports from Africa into the United Kingdom and continental non-Communist Europe probably exceeded the value of such imports from any other area if gold is included and mineral fuels excluded.

Jan 1, 1966