Search Documents

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

By Martin Hertzberg

The concept of limit burning velocities is used to formulate a quantitative theory of flammability limits. Competing processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. There are four competing processes and one complication: (a) Free, buoyant convection, (b) conductive-convective wall losses, (c) radiation, (d) selective, diffusional demixing (the complication), and (e) flow gradient effects (flame stretch). These complexities are unraveled by creating an idealization that is initially freed from these competing processes. The ideal serves as a standard, and its burning velocity (Su), ideal is a unique function of the initial thermodynamic variables of state. By adding each process individually, it is possible to evaluate their significance, quantitatively, in terms of a limit velocity (Su)a , b , c , or e , and to explore the nature of their cooperative interactions. The larger the limit velocity, the more significant the process. The apparently diverse observations of flammability behavior are readily unified within this simple, conceptual framework.

Jan 1, 1976

By L. B. Pankratz

Enthalpies above 298° K were determined for AgCl to 1,400° K and for AgBr to 1,200° K by copper-block calorimetry. Before melting, both compounds showed an anomalous increase in enthalpy, an effect associated with lattice defect formation. Melting points and heats of fusion were determined to be AgCl, 730° K and 2,945 cal/mole; AgBr, 700° K and 2,030 cal/mole. The heat capacity of both melted substances decreased with increasing temperature over the entire liquid ranges investigated. Enthalpies above 298° K were tabulated at even temperatures along with derived entropy increments and heat capacity values. The results were combined with the known heats of formation and entropies at 29.8.15° K to obtain values of the heats and free energies of formation over the range 298.15° to 1,400° K for AgC1 and 298.15° to 1,200° K for AgBr.

Jan 1, 1970

By Jerry W. Ramsey

The Bureau of Mines examined a low-, a medium-, and a high-volatile Pennsylvania anthracite by densimetric methods using four mesh si.s of each anthracite. Using high-pressure mercury the macropore volumes and distributions of these pore volumes determined, densities in mercury were calculated, and specific pore vo1.r. ware obtained from these mercury densities in conjunction with helium densities. The helium densities were also used with the ultimate analyses of these anthracites in calculating structural parameters by statistical densimetric methods. The effect of 106 or 108 rads of gamma irradiation in the presence of air and in vacuum upon the properties studied with two mesh sizes of each anthracite. Results of the statistical densimetric method seem to show some breakdown of condensed ring structural units at the lower irradiation level, with subsequent polymerization at the longer period of gamma irradiation. The structural parameters obtained also indicated that in going from high- to low-volatile anthracite, either the number of condensed rings per structural unit increased, or the degree of polymerization increased.

Jan 1, 1965

By M. B. Shirts

Bench-scale studies were made on a reductive hydrometallurgical procedure to convert chalcopyrite flotation concentrate to copper metal or a readily leachable sulfide. Reductive conversion of chalcopyrite and dissolution of iron and sulfur were accomplished in hydrochloric or sulfuric acid solution by the addition of metallic copper, iron, or lead. Use of metallic copper as the reductant enabled extraction of 95 and 46 percent of the iron and sulfur, respectively. The products were ferrous iron, hydrogen sulfide, and a copper sulfide. Use of metallic iron or lead as the reductant enabled extraction of 95 percent of both the iron and sulfur. The products obtained with metallic iron or lead were ferrous iron, hydrogen sulfide, and metallic copper.

Jan 1, 1974

By Andrew J. Fergus

The purpose of this study was to provide basic information to aid further research on beryllium mineral flotation. Contact-angle and microflotation (Hallimond tube) methods were used to study collector action and flotation response of beryllium minerals and associated gangue minerals with representative commercial surfactants. Chrysoberyl received prime attention. Results indicated that selective flotation of beryl and chrysoberyl from fluorite and quartz is possible with sodium isooctyl phosphate below pH 2, and fluorite and topaz are readily collected by both anionic and cationic surfactants. Several modifying reagents were studied at one pH and one level of collector concentration. Aluminum sulfate, starch, and sodium silicate proved to be depressants in chrysoberyl flotation.

Jan 1, 1968

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By Xavier B. Starnes

The Dike and Eaton veins in Crittenden County, Ky. (fig. 1), are along northwesterly trending relief fractures that lie between two northeastward striking major faults - the Moore Hill and- the Levias, in Crittenden County, Ky. The veins contain small, narrow, irregular ore bodies of fluorspar with subordinate quantities of sphalerite and galena. Gravel fluorspar was found on the surface in the Eaton vein, and open-cut mining was in progress on the W. M. Conyer property about 1900. Discovery of fluorspar in the Dike vein came much later, about 1933, on the W. H. LaRue tract, but the principal production on the Dike vein started after the discovery of gravel spar in 1938 on the land of the P. J. Gilless estate. Production from the Eaton vein was estimated at 9,400 tons and that from the Dike vein at 15,700 tons, a total of 25,100 tons. A large part of this production was gravel fluorspar from within 50 foot of the surface. Beneath the gravel spar the veins are very narrow, averaging 2 to 2.5 feet in width, and the ore shoots are small. The deepest mine level was 140 feet below the surface, and the deepest shaft 150 foot. Orb was concentrated by log washer or sent unwashed to custom mills at Marion, Ky. about 6 miles distant.

Jan 1, 1950

By C. A. Robotham

The following; paper describes underground mining practices of the Riverside Cement Co. of Los Angeles, Calif., in the Stanley limestone deposit at Crestmore, Riverside County, Calif. It is one of a series of papers being prepared for and published by the United States Bureau of Mines on mining methods and costs in tae various mining districts in the United States. ACKNOWLEDGMENTS Acknowledgment is made of the assistance received from E. D. Gardner, supervising engineer of the United States Bureau of Mines Experiment Station, Tucson, Ariz., in connection with the preparation of this paper and of the cooperation of John Treanor, president of the Riverside Cement Co. Valuable assistance in developing the mining methods was obtained from a study of similar practices in the copper-mining; districts of Ray and Globe-Miami, Ariz.

Jan 1, 1934

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By John A. Organiscak

The Bureau of Mines conducted a survey of eight shearer longwall operations to identify factors that affect respirable dust generation from longwall roof supports. The longwalls surveyed were in coal seams located in different geographic regions of the United States. Data were collected on mining (geologic) conditions, support design, operational characteristics, and amount of respirable dust generated from roof supports. Analysis indicated that mining conditions are the main factors that affect the generation of dust during roof support movement. Both roof strength and depth of cover above the coal seam showed relationships with the amount of support dust generated. Several practices are currently employed to effectively control roof support dust; however, some of these controls are limited. More research and development is needed to improve dust control technology for longwall roof supports.

Jan 1, 1985

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

By G. L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from concentrates derived from low-grade domestic chromites. These domestic chromites contain silicon and aluminum impurities at levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten NaOH under oxidizing conditions to form sodium chromate (Na2Cr04)' The reaction product is leached with methanol to recover the majority of the unreacted NaOH, then with water to extract the Na2Cr04 and the remainder of the NaOH. The Na2Cr04 product is recovered by evaporative crystallization from the aqueous solution. This report presents laboratory results of studies to determine the optimum leaching conditions for the reaction products of several domestic chromite concentrates. Results of solution purification and crystallization studies are also presented. The concentrates are from a variety of sources including the Stillwater Complex in Montana, Red Bluff Bay and the Kenai Peninsula in Alaska, and a Ni-Co laterite from southern Oregon. Sodium chromate crystals were produced that contained less than 0.01 pct NaOH.

Jan 1, 1988

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By C. J. H. Brest van Kempen

The objective of this contract was to provide thrust and torque control and visual output torque readout systems to an existing mine roof bolting machine and to test the consistency of torques obtained under actual field conditions. A Lee Norse TD1 roof bolter was modified by adding a simple torque sensing device to the drill rotation mechanism and a pneumatic logic control circuit that measures torque and controls the hydraulic circuit to the rotation motor. The modification controls and indicates the final installation torque of mine roof bolts. A total of over 5,000 mechanical roof bolts were installed in an operating coal mine. The installed torque of these bolts were within an error band (standard deviation) of 8%.

Jan 1, 1978

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010