Search Documents

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By Charles E. McCarthy, MORTON T. PAWEL, E. A. GEE, FRANK S. RIORDAN

Large tonnages of the magnesium silicate mineral , olivine, are known to exist in the mountains of western North Carolina and in the Puget Sound region of Washington. The North Carolina deposits alone are reputed to contain at least 230 million tons of ore averaging 45 to 49 percent of magnesium oxide In both areas the mineral is readily accessible and can be mined by the simplest methods ; one of the largest of the Washington deposits is located at tidewater .

Sep 1, 1946

By M. F. Koehler

[THE LITERATURE contains relatively few thermodynamic values for interoxidic compounds, and these often are unreliable. This is especially true of data for ferrites and aluminates for which heat of formation determinations may involve extreme experimental difficulties. This report contains the results of new experimental work for obtaining the heats of formation of five ferrites (Ca2Fe2O5, CaFe2O4, MgFe2O4,, NaFeO2, and LiFeO2) and one aluminate (CaAl4O7), and a review and revision of previous similar work of this laboratory on five aluminates (Ca3A12O6,, 12/7 CaO-Al2O3, CaAl2O4, NaA1O2, and LiAlO2), The results for the 11 compounds are combined with entropy and high-temperature heat content data to derive tables of heats and free energies of formation (both from the oxides and from the elements) for the temperature range 298° 1,800° K, The relative stabilities of the compounds are discussed. The presented data all have application to ceramic reactions, and those for the calcium and sodium aluminates are applicable in considering soda-lime sintering processes for extracting alumina from silicate minerals such as day and labradorite.]

Jan 1, 1961

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By Benjamin W. Haynes

Analytical procedures are described for the quantitative determination of 16 elements (As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn) and 7 ionic species (NH4, C032-, CI-, F-, NO3-, P043-, SO42-), identification of major and minor mineral components, and measurement of physical properties associated with manganese nodules and nodule processing reject waste materials. Compound identification methods discussed include X-ray diffraction, infrared spectroscopy, scanning and transmission electron microscopy, selective area electron diffraction, and optical and reflected light microscopy. Methods for elemental analysis include atomic absorption spectrophotometry, inductively coupled plasma emission spectroscopy, neutron activation analysis, fluorescent X-ray spectrography, and ion chromatography. Thermal gravimetric analysis, ultraviolet-visible spectrophotometry, ion specific electrodes, and standard wet chemical procedures are briefly discussed. Physical properties determined in manganese nodule materials include grain size distribution, specific gravity, triaxial shear, permeability, maximum density, Atterberg limits, and slurry density. The results of a round-robin analysis of an ammonia process waste material and manganese nodule standards demonstrate the applicability of the discussed methods. Tests discussed for the evaluation of the waste materials for disposal options include the Environmental Protection Agency (EPA) EP toxicity test, the ASTM shake extraction test, and the U.S. Army Corps of Engineers EPA seawater elutriant test.

Jan 1, 1983

By Ned H. Snyder

In recent years the Government and other large consumers of coal have appreciated more and more the desirability of definitely determining by chemical analysis and test the character and quality of the coal they purchase. Higher prices for coal point forcibly to the need of giving more study to engine room and boiler room efficiencies and economies; this implies an intimate knowledge of the character and quality of the fuel used. Analyses and tests of delivered coal furnish data whereby power plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for technologic investigation of fuels and the analyzing and testing of fuels belonging to or for the use of the United States Government, a laboratory is maintained at the Pittsburgh station of the Bureau of Mines, where samples representing deliveries of coal purchased for Government use are analyzed and tested. The Bureau of Mines has been active in promoting the purchase of coal by the Government under specifications/ that is, by contracts that make definite requirements regarding the heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analysis. Under many of these specification contracts the bidders guarantee the quality of the coal offered, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled and analyzed to determine whether the coal is of the quality guaranteed by the contractor, and if it is not, the price to be paid is decreased in proportion; but if the coal is of higher quality, the price is proportionately increased. The known analyses of coals or the guaranteed analyses offered by the bidders may sometimes be used for determining the award of a contract, but if the coals offered differ widely in characteristics, it may be difficult to determine which would prove the cheapest fuel without data on their relative evaporative efficiencies. Hence, the making of evaporative tests under service conditions may be necessary in order to determine which coal is particularly adapted for successful and economical use in a certain plant. Once a particular coal is selected, however, regardless of the procedure of determining the award of a contract, then the greatest advantage of the specification method is realized, for it guarantees the purchaser receiving coal of uniform character and quality, thereby insuring the best results in the plant. The success of the specification method for the purchase of coal and the reliability of analysis now rests largely on sampling.3 Improper sampling leads to controversies, with resulting condemnation of the specification method in general and of the value of laboratory analyses and tests in particular.

Jan 1, 1922

By J. P. Morris

"INTRODUCTION In the investigation being conducted by the Bureau of Mines concerning the production and utilization of sponge iron, it soon became evident that more information was needed regarding methods for determining the degree of reduction attained in the manufacturing process. Sponge irons made by different processes vary in physical characteristics and chemical composition, and a method of analysis that is suitable for one type is not necessarily applicable to all others. For example, the hydrogen-evolution method, which measures the volume of hydrogen evolved upon treating the sample with acid, accurately determines the oxygen content of some types of sponge iron. However, when the sponge iron contains combined carbon, hydrocarbon gases are also-evolved and large errors may result. Probably no single method will give accurate results in all instances, and for this reason it is desirable to have several reliable procedures available and to know the limitations of each.For measuring the degree of reduction, determination of either metallic iron or oxygen should suffice, although for practical application of sponge iron to the production of steel the oxygen content is more significant. After consideration of proposed methods of analysis in regard to their suitability for routine use and the probable influence of other substances, four procedures were chosen for investigation:(1) Mercuric chloride method.(2) Copper sulfate method.(3) Hydrogen-reduction method.(4) Hydrogen-evolution methods."

Sep 1, 1945

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By O. C. Blade

A summary of the characteristics of motor gasoline for the winter 1951-52 is presented in table I, and for comparison, a similar summary for the winter 1950-51 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. The results of this survey show that octane numbers have risen slightly since the summer of 1951 but are below the record levels of the winter of 1950-51. The fractions of a unit change since the summer preceding have resulted in the research and motor-method octane values being virtually the same as the figures for the survey of summer 1950. In volatility characteristics the winter gasolines have changed very little. Average Reid vapor pressures are 10.5 pounds for both grades of fuel compared to 10.4 and 10.5 pounds for premium and regular-price gasolines, respectively, of the winter of 1950-51.

Jan 1, 1952

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By R. A. Bloomfield

This report summarizes Bureau of Mines contract research on the disposal of retorted oil shale. A data base has been developed describing the physical-chemical properties, geotechnical engineering properties, and natural cementation characteristics of spent shale. Results of field compaction tests and seepage pond tests are presented, along with results of a partially saturated finite element seepage model used to predict infiltration and seepage rates. Preliminary engineering analyses are presented for underground disposal systems, which include material transport methods, and for a surface disposal system, which includes stability analyses.

Jan 1, 1981

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By Michael S. Miller

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the nine separate parcels that comprise the 4,330-acre South Warner Contiguous Wilderness Study Area in order to evaluate their identified mineral resources. The nine parcels are along the east side of the South Warner Wilderness. They are, from north to south, the Granger, Milk, Cottonwood, Owl, Hornback, Eagle, Emerson, Barber, and Van Riper parcels. The Wilderness Study Area is underlain by basaltic, andesitic, and rhyolitic volcanic rocks and by sand and gravel deposits. Low-grade metamorphism is widespread in the volcanic rocks, with quartz, zeolites, datolite, chlorite, and calcite locally abundant in veins and amygdules. The rocks have been displaced by the mountain-front Surprise Valley fault and by crosscutting high-angle faults.

Jan 1, 1988

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By F. L. Wideman

This report describes a computer program that is used for the calculation of the coordinates and elevations of subsidence survey pins located by intersection. This program was developed for the Federal Bureau of Mines by the Numerical Analysis Laboratory, University of Arizona. These calculations, although relatively simple, are both tedious and time-consuming when computed with a desk calculator and trigonometric tables. In this survey, a large number of pins were surveyed repeatedly, and it was evident that both time and money could be saved by using a digital computer.

Jan 1, 1962

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By George Markon

The rapid growth and development of the Soviet coal industry rank the U. S. S. R. with the United States among the leading coal-producing countries. The coal resources of the Soviet Union are among the largest in the world, although coal development has been hindered by the disadvantageous location of the coal deposits with respect to the major consuming centers. Although coal production in the U. S. S. R. reached a record high, the total energy output of mineral fuels in 1957 was still far below that of the United States because a significant part of Soviet coal output was lignites or lower rank coals. Although the Soviet coal industry soon may exceed that of the United States in tons produced, the energy equivalent of Soviet output will be considerably less because of the inclusion of a high percentage of lower rank coals. Energy sources in the United States also involve large quantities of oil and natural gas, whereas coal supplies most primary energy in the Soviet Union.

Jan 1, 1959