Search Documents

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By T. J. Ballard

The Track Rock corundum mine was among the numerous corundum deposits investigated during the war by the Bureau of Mines in an effort to develop domestic reserves of that critical mineral. In the investigation of this property 562 feet of trenches were excavated and a l25-foot adit was reopened for the purpose of locating veins to of corundum which had been previously reported to occur in that locality. Only very minor amounts of corundum were disclosed in both the surface workings and the adit. The project was begun in May 1943 and completed in November 1943.

Jan 1, 1948

By Warren E. Morrison

This study was prepared in response to the need for a series of data that reflect the basic flow pattern of energy resources in the United States. To effectively measure and analyze energy,2 it is necessary to prepare balances that reflect both production and consumption, and the various forms energy resources take at different stages of utilization. Before energy can be measured it must also be put into a common unit. In this study the common unit used is the British Thermal Unit (Btu). The ideal point to survey energy is at the stage of final ultimate use, representing the useful work derived from the interaction of energy inputs and the prime mover. Unfortunately this concept of efficient or useful work from energy output cannot readily be measured in the aggregate. With the present available official data, energy measurement can be carried to the point of calculation of net inputs of energy3 into the economy at various stages of utilization. However, preparation of energy balances, on a net basis is hampered by the fact that this can only be done for years when the censuses of Mineral Industries and Manufactures are taken, usually at 5-year interval.

Jan 1, 1964

By Warren E. Morrison

This study was prepared in response to the need for a series of data that reflect the basic flow pattern of energy resources in the United States. To effectively measure and analyze energy,2 it is necessary to prepare balances that reflect both production and consumption, and the various forms energy resources take at different stages of utilization. Before energy can be measured it must also be put into a common unit. In this study the common unit us d is the British Thermal Unit (Btu). The ideal point to survey energy is at the stage of final ultimate use, representing the useful work derived from the interaction of energy inputs and the prime mover. Unfortunately this concept of efficient or useful work from energy output cannot readily be measured in the aggregate. With the present available official data, energy measurement can be carried to the point of calculation of net inputs of energy3 into the economy at various stages of utilization. However, preparation of energy balances, on a net basis is hampered by the fact that this can only be done for years when the censuses of Mineral Industries and Manufactures are taken, usually at 5-year intervals.

Jan 1, 1964

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

In 2007, a total of 725 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Nonmetal mines com-prised 4.9% of all m ining operations. ? Mines producing common clay comprised 25.4% (n=184) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the U.S. Virgin Islands.

Aug 1, 2009

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By Stanton L. Tainter

As a part of a wartime program to aid in the development of known ore bodies and in the discovery of hitherto unknown deposits of strategic minerals, the Bureau of Mines investigated the feasibility of diamond-drilling the Christmas copper deposit, in Gila County, Ariz., to increase the reserves of milling ore. Upon recommendation of the examining engineer, drilling was begun in September 1942, from the bottom (770) level of the mine. One month later, in cooperation with the Bureau, the Federal Geological Survey started geologic mapping of the mine workings. Since extensive and costly development would be required, the War Production Board concluded that ore below the bottom level could not be mined at that time because of the wartime shortages of equipment and man-power. In January 1943, drilling was moved to the 300 and 400 levels to locate reserves readily accessible for continued production of fluxing ore. This drilling, which was under the supervision of L. G. Marshall, was completed in January 1944.

Jan 1, 1948

By L. C. IlsLey

It is most unfortunate that a few must often suffer , and perhaps die , that many may benefit from a fuller appreciation of the dangers surrounding mining operations , and the proper use of safeguards designed to offset these dangers . This has been the case during the last few months in the anthracite field , where several explosions , resulting in burnings and fatalities , were undoubtedly caused by the use of defective or improperly assembled flame safety lamps . Had this same lack of understanding regarding the proper assembly of this safety device , and had the same indifference on the part of the user in keeping the lamps locked at all times and in proper condition , been permitted in a region where the coal dust was explosive , a terrible disaster would surely have resulted . In nearly every coal -mining country , including the United States , the Davy and Clanny type of lamp has been superseded , and rightly so , by some kind of bonneted lamp . Bonneted lamps , especially of the naphtha type , while much safer than the unbonneted , have more parts and need more care in assembling . For this reason the burden of responsibility for their being properly assembled rests with the lamp man ; therefore , it is extremely important that only competent , conscientious men be given this work .

Dec 1, 1921

By D. J. Parker

Since the introduction of electricity into the mines of the United States , the hazards incident to the industry have increased materially in both coal and metal mines . For economic reasons the tendency at present , particularly in coal mining , is decidedly toward the adoption of electrical mine machinery , including alternating current machinery , on a more extensive scale than ever before . Obviously, the growing use of such equipment will result in an ever -increasing number of underground transformer stations . The principal electrical hazards in mines are threefold ; fire , explosion, and contact . Of these , fire is the greatest hazard involved in the use of electricity underground , and several fires have originated in underground transformer and motor generator set stations . The fire hazard due to improperly installed and poorly maintained underground transformer stations is an ever-present one , and failure to take the necessariman remedial action is likely to result , sooner or later, in the destruction of life and property . Upon suggesting the necessary corrective measures with respect to such installations , one is often confronted with the statement to the effect that even though this particular hazard has existed over a period of years , there have been no unfavorable results therefrom thus far . Frequently , the desirability for action is not apparent to the mine management until it is too late . Because a mine has a record free from fires , explosions , etc. , over a number of years of operation during which these hazards existed , such good fortune should not be taken as a guarantee that this or any other mine is immune from these common dangers . When the elements of an existing hazard are properly balanced or in the right proportion, the unfortunate combination must of necessity culminate in misfortune of one kind or another. The fire hazard due to underground transformer installations can be very definitely minimized by proper installation and maintenance . In coal mines the transformer banks , connected to 2,300 and occasionally to 4,400 volt circuits , are often found located in open- ended crosscuts , mounted on concrete or timber foundations , and in nonfireproof surroundings .

Jul 1, 1930

Develop and evaluate a mechanical position and heading system (MPHS) that provides information about underground mining machine position and heading to aid in the remote positioning of mining machines during face maneuvers. Background While great improvements have been made in mineworker safety, progressive technology continues to create a safer, better working environment for miners by keeping them away from the dangerous face area. In maintaining such high standards of safety, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A key component of computer-assisted operation is a guidance system. Since there are no guidance systems on any commercial continuous mining machines, the Bureau itself developed and tested the mechanical position and heading system (MPHS). The MPHS is based on linear position transducers (LPT's), and operates on principles of triangulation to provide machine position (xy coordinate), and orientation in the xy plane (yaw or heading). These data are needed in order to keep the continuous mining machine in proper alignment before and during the cutting cycle. The MPHS theory development is in three parts: characterize the sensors used and their configuration; select and define the navigation reference frames; and derive a closed-form solution for determining the position and beading from sensor information. Application of the MPHS theory required the development of hardware, software, and system interfaces.

Jan 1, 1992

By Stephan Stecura

Crystallographic modifications and kinetics of solid-state phase trans-formations were determined for five rare-earth" sesquioxides--La2O3, Nd2O3, Sm2O3, Eu2O3, and Gd2O3. Oxides used for crystal modification studies were prepared by thermal decomposition of the following high-purity salts of the five rare-earth elements--carbonates, chlorides, fluorides, nitrates, oxalates, and sulfates. X-ray diffraction patterns of the cubic and hexagonal oxides were indexed by a graphical method and patterns of the monoclinic oxides by Ito's method. The kinetics of crystallographic transformation were determined by high-temperature X-ray diffractometry. The kinetic data were interpreted using a shrinking sphere model. All of the transformations followed first order kinetics. Activation energies were calculated by application of the Arrhenius equation. These solid-state phase inversions were concluded to occur by a reconstructive transformation mechanism.

Jan 1, 1965

Researchers with the National Institute for Occupational Safety and Health (NIOSH) have developed a training module to educate both new, inexperienced miners as well as veterans on important issues related to self-rescue and escape procedures. These include: (1) physical and environmental conditions that can be encountered in a mine after a major explosion, (2) knowledge of emergency meeting locations and escape routes, (3) the importance of using self-rescuers, even in seemingly clear air, to keep the lungs isolated from contaminants, and (4) why miners should not go off to look for others who are missing. In addition, the module may stimulate miners to think about and discuss mine explosions and the devastating effects of such an event.

May 1, 2009

By William A. Beck

"The Old Cline mine, also known as the Old Cruse mine, was first worked for gold in1895. The property was opened by several shafts and trenches; and some stoping has been done, producing several cars of copper-gold ore in the early nineteen hundreds. Chalcopyrite is visible in selected samples; and, with the aid of a mineralite, several samples showing a considerable amount of scheelite were found on the old waste dumps.The mine is in Township 6, Cabarrus County, N. C., 5 miles north of the village of Mount Pleasant, 10 miles northeast of Concord, and about one-half mile south of Watts Crossroads. It is one-fourth mile east of the county road.When examined, the property was owned by H. F. Tompkinson, Concord, N. C., and was leased, with option to buy, by L. Nash. Titles of record were not investigated.As stated above, the Cline mine was first worked in 1895. The property was Purchased in 1902 by J. A. Clark and A. A. Smith of Atlanta, Ga., and worked for gold and copper. No record is available of the quantity of ore removed during these operations.A Bureau of Mines mining engineer3/ examined the mine as, a copper prospect on October 13, 1944.The Cline mine is in an area characterized by flat to rolling topography, dissected by many streams and rivers. It lies in the Piedmont Plateau and Varies in elevation from 700 feet to 800 feet. The surrounding country is partly wooded and partly cleared farm land.A quartz vein occurs in country rock of quartzite and greenstone.4./ The ore occurs in a series of quartz lenses, having a width of 1 to 3 feet and dipping about 750 NE, and striking N. 300 W. All these lenses have fairly sharp boundaries and in some cases are entirely separated from each other, while at other times they are connected by thin stringers of quartz. They can be traced for 1,000 to 1,200 feet by a series of shafts and test pits."

Apr 1, 1946

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

To reduce operator exposure to drilling noise from roof bolting machines. Background Noise-induced hearing loss (NIHL) is a prevalent occupational illness in the United States. Studies indicate that 70%?90% of miners have NIHL significant enough to be classified as a hearing disability. Mine Safety and Health Administration studies indicated that roof bolting machine operators are among those overexposed to noise. Field studies support the premise that, on average, drilling is the loudest noise source to which a roof bolting machine operator is typically exposed and contributes greatly to the operator?s noise exposure. The National Institute for Occupational Safety and Health (NIOSH) has further determined that the drill steel and chuck radiate a significant amount of noise during drilling. To address this noise hazard, NIOSH developed a collapsible drill steel enclosure (CDSE) to encapsulate the drill steel during the drilling portion of the roof bolting machine duty cycle. In addition, NIOSH is collaborating with J. H. Fletcher & Co. in the continued development of a CDSE.

Sep 1, 2008

Apply state-of-the-art monitoring and computer systems technology to remotely monitor geostructural data and evaluate ground conditions in near real-time. Background Recently, the coal mining industry has progressed dramatically from a labor-intensive industry to highly mechanized and automated systems achieving significantly higher production rates. In underground longwall coal mines, production and face advance rates have increased by almost tenfold in the last 15 to 20 years. With increasingly high advance rates, geologic anomalies which affect rock mass quality are encountered more frequently, far exceeding the current rate at which ground control information can be processed and analyzed. As a result, mine operators find themselves with insufficient time or resources to cope with the rapidly changing ground conditions. To keep up with the technological advancement in mining and the associated ground control problems, the Bureau of Mines is conducting a multi-phase research pro¬gram to implement a computer-assisted Ground Control Management System (GCMS). Research is ongoing at present, but when completed the system will be designed to 1) monitor and evaluate data on rock properties, geologic conditions, and rock mechanics data from underground sensors in near real-time; 2) interpret the analyses to evaluate the interaction between various critical ground control parameters; 3) assess the structural integrity of the mine; and 4) determine failure modes and provide recommendations for control measures, design modifica¬tions, and alternative support procedures. The system will be expanded into its full capability during various phases of this research program.

Jan 1, 1991

By T. M. Barczak

This U.S. Bureau of Mines report investigates shield mechanics and component stress development in a two-legged longwall shield for unsymmetric canopy and base contact configurations. Previous studies analyzed shield behavior for symmetric contact configurations. The goals of these efforts are to improve longwall support selection and design. This study provides vital information that will help develop improved procedures for performance testing of longwall supports and will benefit future research to improve support design through stress optimization and evaluation of failure mechanisms. Combinations of six canopy (three symmetric and three unsymmetric) and six base (four symmetric and two unsymmetric) contacts provided a total of 36 configurations for evaluation. Of these 36 configurations, 10 were eliminated because of fixture limitations or shield instability. Controlled vertical and horizontal displacements were applied by the Bureau's mine roof simulator to the remaining 26 configurations. Component responses were determined from pressure transducer and strain gage instrumentation in order to identify contact configurations and boundary displacements that produced maximum loading in each of the support components. This report describes these test results and provides conclusions relevant to critical contact configurations for performance testing of longwall supports.

Jan 1, 1990

By A. D. Garman

The mining ordinance of Costa Rica dates from 1830. In spite of the numerous attempts to enact a new ordinance , it has been so much amended and reamended during the hundred years of its existence either expressly or , more often , by implication , and sometimes by Executive Decrees of which the validity has been called in question - that in most cases no one but a lawyer thoroughly conversant with Costa Rican mining practice could properly advise with reference to it . The present attempt at a digest of these laws is based on the 1929 edition of Bolandi and Johanning - the only source available in Washington . Apparently this edition has no official character , and the editors themselves often made surmises although one would think that definite facts would be available in Costa Rica where it was published .

Jul 1, 1930

In 2005, a total of 4,490 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.6% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,039; 45.4%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Of all states, Pennsylvania had the most stone mines (n=379; 8.4%).

Jan 1, 2008