Search Documents

By D. Harrington

"In at least three out of every four working faces in metal mines there is no attempt made to cause air circulation other than by use of compressed air, and in at least nine cases out of ten the compressed air is released merely by opening, or partly opening, the valve and allowing the compressed air to escape through open air hose used to convey the compressed air to the drilling machines. Usually no blowers are in use during periods of drilling, as the exhaust from the drill provides cool, comparatively fresh air for the driller; however, in some instances, the compressed-air line is provided with a tea connection, which permits taking air for the drill from one side of the tee, and air for ventilation through a separate hose used as a blower, simultaneously with drilling.Table 1 contains temperature and humidity data as to compressed-air blowers from open end of air hose at 36 working places in eleven metal mines of four States, embracing the mining of gold, silver, copper, lead and zinc ores, and at horizons ranging from 500 feet below the surface to as low as 4900 feet.It is noticed that the ordinary air surrounding the worker at the face gives an average wet bulb temperature of 81.7° F. for the 36 working faces, with 84.7° F. dry bulb and 87.2 per cent relative humidity. The average wet bulb tem¬perature of 36 readings at these working faces of compressed air at the end of the,hose as the air issues from the hose was 67.4° F., or 14.3 degrees lower than the average wet bulb readings of the air of the working places; however, the average dry bulb temperature of the 36 readings of compressed air as it issued from the end of the hose was 79.7° F., or only 5 degrees less than that of the general air (84.7°); the relative humidity was 51.1 per cent as against 87.2 per cent for the surrounding air. Readings were taken in five raises, seven crosscuts, ten drifts and 14 stopes.It will be noted that the velocity or movement of the general atmosphere at each of the entire 36 working faces, was found to be practically imperceptible; this might readily be inferred since compressed air is rarely used on blowers if there is adequate circulation of the general air of the place. Where rook temperatures could be obtained readily, they are shown; it is noticeable that the dry bulb temperature of the air of the working place varies little from the rock temperature, and that the dry bulb temperature of the compressed air as it issues from end of air hose varies only a few degrees from the temperature of the surrounding rock; in some instances the dry bulb temperature of the compressed air as it issued from the end of the air hose was higher than the rock temperature or the dry bulb temperature of the surrounding air."

May 1, 1921

By William H. Pailes, Vincent Castronova, Daniel Lewis, Norman L. Lapp, George Goodman

"INTRODCJCTIONAlveolar macrophages are free lung cells located on the surface of small airways and alveoli. These phagocytes play an important role in the protection of the lung against airborne bacteria and particles.1 However, hyperactivation of pulmonary phagocytes can lead to excessive secretion of enzymes and reactive oxygen species which could result in lung injury, emphysema, or fibrosis.2,3 Analysis of bronchoalveolar lavage effluents for cell types and cellular activity has yielded information concerning the etiology of various pneumoconioses. For example, emphysema associated with inhalation of coal dust or cigarette smoke has been related to enhanced secretion of reactive oxygen species from alveolar macrophages.4-7 In contrast, hypoactivation of alveolar macrophages has been associated with inhalation of diesel particulates"" and has been related to increased susceptibility to pulmonary infection. s Inhalation of cotton dust has been associated with dramatic increases in lavagable polymorphonuclear leukocytes9 while pulmonary sarcoidosis and silicosis have been related with high numbers of lymphocytes in lavage effluentsl0,11The objective of the present study was to obtain lavage effluents from 8 control subjects, 8 healthy power plant workers exposed to fly ash, 1 healthy coal miner, and 1 rock driller with acute silicosis. These effluents were analyzed for total numbers of alveolar macrophages, lymphocytes and neutrophils and for secretory activity of alveolar macrophages. Data were then analyzed to determine what response patterns were characteristic for given dust exposures.METHODSSelection of SubjectsThe 8 control subjectS were all adult males from the area of Morgantown, WV. Two subjects among the controls had smoked cigarettes for approximately three pack-years and had stopped more than ten years ago. The 8 power plant :workers were all healthy adult male employees of a power facility in Hatfield, PA, approximately thirty miles from Morgantown. One of the power plant personnel was a comparable ex-smoker. The remaining subjects were all lifelong non-smokers. The coal miner was a healthy non-smoking male from Morgantown, WV. The rock driller was a patient under treatment with corticosteroids for acute silicosis. He had shown considerable clinical improvement with this treatment but still manifested significant radiologic and pulmonary functional abnonnalities at the time of lavage. The mean age of the 8 control subjects was 36 years (range: 31 to 49 years); the mean age of the remaining subjects studied was 38 years (range: 29 to 53 years)."

Jan 1, 1990

By Noel N. Moebs

Studies by the Bureau of Mines have identified geologic structures in mine roof rock that contribute to many roof falls in Appalachian coal mines. These structures, including paleochannels, scours, pinchouts, slickensides, clay veins, crevasse splays, and joints, can often be identified during, and sometimes before, mine development. Mine projections can be revised to reduce the adverse effects of discontinuitites in roof structure; large roof areas of laminated sandstone or incompetent strata generally can be delineated or inferred from exploratory drill hole data, and the need for supplementary support can be anticipated. Accurate descriptions of roof geology also provide some indication of optimum length and type of roof bolts that should be installed.

Jan 1, 1981

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By S. C. Tadolini, T. M. Barczark

Mines in the western United States have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the earl v 1990s provided an effective alternative, (lilt/ it remains the dominant form of tail¬gate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled to¬gether; provides more capacity than (m equivalent sized Call support and improves transport efficiency. However the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but the \' have not been proven in high deformation en¬vironments. This paper compares the performance characteristics o f these various support systems.

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By Deno Pappas, Gregory Molinda, Eric Bauer, Christopher Mark, Daniel Babich

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3- way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

By Roy H. Grau, John C. LaScola

This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.

Jan 1, 1984

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By Lars Osen

This investigation was undertaken to contribute to the understanding of underground pull tests by conducting laboratory tests under closely controlled conditions. Steel bolts, instrumented with electrical resistance strain gages, were anchored in an aluminum block, a granite block, and a steel sleeve, and were subjected to pull tests. The bearing plates used were either flat7 dished, or embossed. In pull testing a bolt that is prestressed, there is a range of loading during which bolt load is greater than the jack-applied load, This study showed that preload, the size, shape, and type of bearing plate; and the geometry of the system determine the point at which bolt load and applied load become equal. The effects on bolt load of both a theoretical solution and actual pull tests were analogous and led to similar results.

Jan 1, 1965

By W. D. Bensema, J. W. Adams

A portable, multichannel battery-operated mine-permissible measurement system was developed to measure the rms magnetic-field noise spectrum in the frequency range from 100 Hz to 375 kHz. During each measurement, the entire spectrum is measured simultaneously through the use of time-domain recordings which are later analyzed by Fast Fourier Transform processing. Dynamic ranges of 60 dB in a 125 Hz bandwidth are obtained for spectra covering the range from 100 Hz to 100 kHz. The method also allows a three-dimensional display of the way spectrum occupancy changes with time. Calibration and correction procedures allow absolute field strength measurement with an uncertainty of not more than 3 dB. We feel that further analysis of the system errors will allow this uncertainty to be reduced to less than 1 dB. Ambient magnetic field noise spectra covering frequencies from 100 Hz to 100 kHz are given for several underground coal mine locations. Examples are also given of magnetic field noise on the surface above the mine, noise in the mine face area, noise radiated by specific equipment, the voltage spectrum found on a 600 V dc trolley wire, and noise picked up simultaneously on loops and on roof support bolts.

Jan 1, 1973

By Thomas C. Atchison, Joseph M. Pugliese

Six explosives were compared by measuring their strain- producing abilities in limestone . Peak strain , e , varied with scaled distance , R/Ro , according to the following equation : € = Kc (R /R 。)- ". The distance exponent , n , was a constant of the rock and did not depend upon explosive . The strain intercept , Ke , increased with increasing detonation pressure of the explosive . The strain intercept also depended upon the explosive- to - rock impedance ratio . For impedance ratios from 0.53 to 1.38 , the strain intercept was approximately proportional to the medium stress , Pn , as calculated from the explosive detonation pressure , P , and the explosive - torock impedence ratio , Z , by the simple elastic theory relation : P = 2P / ( 1 + Z ) . PD However , the data indicated that , at lower values of impedance ratio , the strain intercept is relatively larger than would be expected from the simple elastic theory . The results presented provide a simple method for predicting the relative effectiveness of different explosives in breaking limestone from the detonation pressures and characteristic impedances of the explosives .

Jan 1, 1964

By D. E. Wolfson

The Bureau of Mines investigated the use of preheated coal in carbonization operations. Liquor yields and coking times were reduced, coke quality was improved, and smokeless pipeline charging to coke ovens should eliminate a serious source of pollution.

Jan 1, 1972

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

Develop a simple and economical technique for determining the absolute stresses and the change of stress on the surface of roofs, floors, or walls in miners. Approach Use a commercially-available, permissible, Whittemore-type gage to determine the stress at the surface of a mine opening and to monitor any stress changes that might take place. How It Works The following equipment is used: ? One steel templet (for laying out a 60° rosette on the: rock surface). See first photograph. ? One 3/8-inch rock drill bit for drilling holes for the rosette pins. ? Six stainless-steel rosette pins. ? One Whittemore-type mechanical strain gage. ? One drill (not shown). ? Epoxy for cementing the rosette pins. ? Tape to hold the pins while the epoxy sets. The following procedure is used to determine the absolute stress on the rock surface. 1) Spot the location of the rosette pins with the templet. 2) Drill the pin holes and set the pins with epoxy cement. 3) Measure and record the distance between the pins across three diameters of the rosette with a 10-inch Whittemore-type gage. See diagram. 4) Drill a 1 1/2-inch diameter hole in the center of the

Jan 1, 1981