Search Documents

By Eliot J. White

The Bureau of Mines tested cores from 35 wells from 14 oil-producing zones in southern Illinois, southern Indiana, and western Kentucky to determine why rates of water injection were apparently low in some zones. Since these zones contain only minor amounts of clay minerals, it is concluded that permeability reduction results from movement of dislodged silica particles and other material, including the clays, that lines the pores. Both single-phase and two-phase permeability measurements, however, indicated that most samples had only low to moderate water sensitivity, so that permeability reduction due to such particle movement should usually not be of practical significance. The effective permeability to water was considerably lower than the effective permeability to oil during two-phase flow measurements, as is typical of most reservoir rocks. It can be concluded, therefore, that relatively high injection pressures will be required in waterflooding thin zones or zones having low permeabilities.

Jan 1, 1966

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By N. Kumar Kittusamy, Richard E. Miller

This field study evaluated a newer and older dozer at a construction site. Both dozers performed similar activities in the same location within the construction site. Two operators participated in this study. One operator used the older equipment and the other operator used the newer equipment. Jolting and jarring measurements were taken at the seat/operator interface and at the floor of the cab. The result of this field study indicates that the newer dozer was better than the older dozer.

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By Frank C. Andreuzzi

The Federal Bureau of Mines conducted a demonstration project to reclaim 125 acres of abandoned strip-mined land in Lackawanna County, Pa., for public recreational, historical, and educational use as a park. The Bureau was involved in the development of the general site plan, and engineered and supervised the basic land rehabilitation. The park's Facilities include outdoor recreational activities, picnic grounds, children's play areas, primitive overnight camping, and winter sports. A major attraction is the Anthracite Museum constructed by the Pennsylvania Historical and Museum Commission The project may serve as a prototype for reclaiming existing and future surface-mined lands.

Jan 1, 1976

The Bureau of Mines has successfully used sulfur hexafluoride (SF6) as a tracer gas to measure mine air flows under conditions where conventional methods have failed. SF6 was employed experimentally to measure accurately recirculation of return into intake air caused by leakage through an old stoped area, to check for potential leakage from an adjacent mine, to trace 10,000 cfm of "lost" air from an intake airway, and to measure transit air time through uranium mines. It proved useful as a means of accurately measuring airflow volumes in airways of large cross section and very low flow velocity, and in determining the recirculation resulting from underground cooling plants.

Jan 1, 1974

By J. T. Dunham

The Bureau of Mines studied by dilatometry the effect of titanium on the thermal expansivity of hot-rolled zinc and Zn-l percent Cu alloy. The titanium content of the alloys was varied up to 0.3 percent. Expansion coefficients were determined from measurements made both parallel and perpendicular to the plane of the rolled sheet. Titanium reduced expansion parallel to the plane of the sheet, especially in the rolling direction, but increased expansion perpendicular to the sheet. Basal-plane pole figures showed that the degree of preferred orientation increased with the titanium content in the alloy, and that anisotropic expansion can be correlated to sheet texture.

Jan 1, 1965

By T. F. Dumm, O. Trass, V. R. Koka, L. G. Austin

"The size distributions of carefully screened 2 size fractions of ground materials were determined using a Microtrac laser dif-fractometer. The size distributions were fitted to the empirical function P(x) = 1/[1 + (x50/x)1] where P(x) is cumulative mass fraction less than Microtrac size, x. The standard deviation of A for a 50 second test time was approximately 0.5, so that seventeen test times give a mean with an estimated error within t 0.25 (95% confidence level). Values of were 5.44, 4.82, 4.40 for a coal ground under different conditions, indicating statistically different shape distributions; the average value for mica was 2.91 owing to the high aspect ratio of the particles. The ratio of x50 to the geometric mean sieve size was 1.2 for the coal and 0.70 for mica.1 IntroductionKoka and Trass have presented evidence [1,2] that materials ground in the Szego mill [3] give different shapes depending on the milling conditions. The variations in shape were deduced qualitatively by viewing SEM photomicrographs of selected 1/2 screen fractions. This paper quantifies their observed differences in shape by using measurements of the size distributions of screen fractions examined in a laser diffractometer [4] (Microtrac, Model 7991). The basic concept is that particles of 'a given ""screen"" size will give a wider distribution of ""Microtrac"" size when the particles are flaky with high aspect ratios, and a narrower distribution when the particles approach the cubical and spherical geometries.2 TheoryAustin and Shah [5] have shown that coal screened within a 1. 1/2 upper-to-lower sieve size range will give rise to a much wider distribution of Microtrac size. They found that the screen interval of irregular fragments of comminuted coals or quartz gave Microtrac size distributions which could be described by the simple function"

Jan 1, 1988

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

By Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 Am. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By Albert E. Long

This paper presents a description of the operational mechanics involved in block-caving a granodiorite-capped, limestone deposit. This method was used for 24 years at the Crestmore mine, near Riverside, Calif., which was operated by the Riverside Cement Co. as a source of raw material used to manufacture a portland cement. The Crestmore mine is the only place where a block-cave method has been used to mine a limestone deposit. Structurally, limestone is relatively strong, and it is not usually considered to be a substance amenable to mining by block caving. It is therefore a credit to the engineering department of the Crestmore mine that it developed a satisfactory, relatively efficient method of block-caving a structurally stable rock. In the discussion, covering the methods applied to produce about 7.9 million tons of limestone and granitic rock materials by block caving, particular emphasis has been placed on an assessment of (1) physical properties of the deposit, (2) ground pressure and support, (3) methods used to induce fragmentation and maintain cave action, (4) surface and subsurface subsidence, (5) secondary blasting of oversize, (6) production rate, (7) safety, and (8) the advantages and disadvantages of the cave method as applied to this specific limestone deposit.

Jan 1, 1958

By C. H. Elder, M. C. Irani

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand- stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By T. C. Higgins, J. S. Malesky, J. A. O'Connor

"INTRODUCTION This circular contains the story of a stubborn mine fire of electrical origin that started on the main haulage road of No. 59 mine of the Peabody Coal Co. and illustrates that sometimes serious fires can be fought by direct attack. The story also points out that the cost of such procedure can be extremely high, and it is better, therefore, to minimize the possibility of a fire of electrical origin by suitable over-current and line-fault protection. The lives of 163 men were saved by utilizing a recently sunk air shaft near active workings as an escapeway. These men could not have reached the older openings. Also described are the rescue of 75 additional men through another air shaft, sealing of the fire, attempted extin¬guishment with carbon dioxide, and the difficulties of fighting the fire and recovering the mine.A fire occurred shortly before 12 o'clock noon, August 15, 1949, in the No. 59 mine, Peabody Coal Co., Springfield, Ill. All 257 men underground escaped to the surface. One group of 75 men was delayed from escaping for several hours after the alarm was given because smoke and fire gases were circulating in a main return airway, which intervened between their working section and one air shaft, and also in the stairway compartment of the shaft. After being supplied with universal-type gas masks, or self-rescuers, these men were conducted from the mine by members of a State mine-rescue team and other mine employees. Six nine officials were hospitalized because of exposure to carbon monoxide during fire-fighting activities; all were discharged a few days afterward. Later, while doing work incident to fighting the fire, two men were killed, and several were injured by falls of roof and rib.The fire broke out after a collision of a loaded trip with four empty mine cars on the main east haulage entry. The mine cars were jammed against the trolley wire causing a sustained electric arc that ignited the wooden mine cars and the fire spread to the timbers and coal."

Apr 1, 1950

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By J. G. Linn, H. H. Schrenk, W. P. Yant, R. R. Sayers, John Chornyak, F. A. Patty, S. J. Pearce

"This report is the first of a series dealing with the results of a comprehensive investigation of methanol poisoning, conducted jointly by the Federal Bureau of Mines, Carbide & Carbon Chemicals Corporation, du Pont Ammonia Corporation, and the Commercial solvents Corporation.The study dealt mainly with physiological effects produced by inhalation of methanol vapor, and concentration studied ranged from approximately 500 to 15,000 p.p.m., and periods of exposure from 4 hours daily to continuous. The range of concentrations and periods of exposure were such as to produce acute effects, with and without fatalities, by a singel exposure and chronic poisoning, with and without fatalities, as well as little or no response after repeated daily exposures. In addition to the inhalation experiments, skin absorption was studied, and field surveys were made to ascertain the hazards associated with the manufacture and, use of methanol."

Feb 1, 1942

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

Maps To Accompany Bulletin 507

Jan 1, 1952

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) Fn the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By R. Van A. Mills

Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effect's on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been "Freshened" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.

Jan 1, 1928

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931