Search Documents

By Jr. Sayre

Results of studies of reservoir and wax-precipitation temperatures relating to wax deposition in the reservoir of the Bradford oil field are presented in this report. During 1949 and 1950 Bureau of Mines engineers made temperature measurements in 42 wells, which indicate that the Bradford Third-sand temperatures range from 59.7° F., at 1,150 feet, to 71.9° F., at 2,040 feet. Reservoir temperatures measured at the same depths in newly drilled wells and oil-producing wells differed as much as 4.5u F. Injection-well temperatures measured during water injection showed that the temperature of the water entering the sand was 11.5° F. lower than reservoir temperatures before injection. The cooling in the formation resulting froth the injection of low-temperature water was 11.5° F. in the vicinity of the injection-well bore, and a maximum of 2.1° F. 200 feet from the injection well. Sand temperature, after 5 months of water injection, was reduced 1.5° F. 90 feet from water-injection wells. The temperature at which wax begins to precipitate from solution in crude oil was determined at atmospheric pressure for 26 samples and ranged from 51° to 67° F. Oil samples from wells producing no water had wax-precipitation temperatures ranging from 51° to 58° F. and wax contents from 2.20 to 2.97 weight percent, whereas the samples from wells producing water and oil had wax precipitation temperatures ranging from 580 to 67° F. and wax contents from 2.57 to 3.42 weight percent .

Jan 1, 1952

By D. R. Tesarik, R. W. McKibbin

Material properties affecting slope stability were measured in a large 50-year-old, partially consolidated rockdump located in an active open-pit mine. Field tests included single-ring infiltration and density. In addition, a nuclear depth-moisture gauge was used to measure water content in six stainless-steel-cased drill holes on the crest and an upper bench of the rock dump. Precipitation, evaporation, wind speed and direction, and temperature data were collected at a weather station installed on the dump’s crest. Laboratory tests included particle-size distribution, specific gravity, Atterberg limits, and water content. By measuring material properties of a rock dump presumed to be stable, the safety of miners working on or at the toe of old rock dumps constructed of similar material and located in a similar climate can be assessed.

Jan 1, 1999

By David C. Peters, Robert S. Crosson

A method of error analysis has been applied to the location technique of non-linear least squares iterative inversion in order to evaluate the resolving power of several seismic array configurations with various assumed earth models and errors and inaccuracies in arrival times. The results obtained demonstrate that lateral accuracies of location are improved significantly when the depth of the miner is known. Lateral location to within 100 feet appears achievable in many instances. If it is possible to refine earth models significantly beyond what has normally been assumed in this work by the use of on-site data, or if the mine is shallow (300 feet or less), accuracies of-about 30 feet or so may be attainable. Inaccuracies in earth models of about 5% are found to contribute much more heavily to these location inaccuracies than errors of a few milliseconds in picking arrival times; however, arrival time errors of 15-20 ms or above will dominate these model inaccuracies. The expected accuracy of location is found to fall off very rapidly as the miner moves outside the array. The strength of this effect depends markedly upon the geometry of the array configuration and can be reduced by careful design. Also, as the size of the array is increased, expected location errors within the array are not altered much, but continue to match the error associated with the smaller array over a larger area (assuming that all stations can still pick up the miner's signals). Better location accuracy, especially with respect to depth control is achievable in an earth where the velocity is depth-dependent (increasing with depth) than in one which is homogeneous. This is an advantage since the

Jan 1, 1974

By V. F. Parry

[Approximatel~r 7-1/2 illion tOlls of subb1tnminous coals are mined an-nuall in Colorado, Wyo~ing, and Montana, of which 50 percent probably reaches dome ,-tic conswno:os. r:L'he moi s t'_re of the se subbi t1.Uninous coal sis high, averae;:t.:ug about 25 :!,)ercent \-Then they are :nined. T'ne coals are non-caking d ~~ack to a vari ble degree when exposed to nornal atmospheric conditions. ~hey a~e gpod domestic fuels, are considered to be smokeless in most furn~ces, and have been used. f, r f!1an: y ars in hand-fired domestic furnaces in hich tnc practice i~ to e~ploy large lureps for efficient com-]

Jan 1, 1941

By J. G. Kirby

According to the annual Bureau of Mines survey of refinery capacity, there were 343 petroleum refineries in the United States as of January 1, 1953, with a total daily crude-oil throughput capacity of 7,638,661 barrels. Compared with the previous year, this represents a decline of 7 in the total number of refineries, but a gain of 305,776 barrels in daily crude-oil throughput capacity. The capacity of the average refinery to process crude oil increased to 22,270 barrels, a gain of 1,319 barrels during 1952. All refining districts reported increases in installed capacity for the year, with Texas Gulf Coast accounting for 28 percent of the increase; California, 21 percent; and the Indiana-Illinois-Kentucky district, 18 percent. Additional crude-oil capacity under construction January 1, 1953, was 60 percent greater than at the beginning of 1952. The total reported, 509,721 barrels daily, is a record high for refinery expansion. In addition to the new facilities under way, facilities for 127,755 barrels daily are being installed to replace those that are obsolete. Four new refineries were under construction at the beginning of the year, and three of these are now in operation. Plans for five' new refineries have been announced, but actual construction has not been started.

Jan 1, 1953

By Vernon Helm, John S. Ball, Welton J. Wenger, William E. Haines

"INTRODUCTION Although the presence of sulfur causes many petroleum’s to be classified as ""low-grade"" because of the difficulties encountered in manufacturing products to meet rigid specifications, the petroleum industry is finding it necessary to use such crude oils to satisfy present needs. As the demand for petroleum products increases, and available reserves diminish, this utilization of high-sulfur crude oils will be accentuated. Programs designed to supplement the supplies of fuel available from petroleum by the manufacture of synthetic fuel from natural gas, shale oil, and coal are in progress. Such fuels, especially shale oil and, less so, oil from the hydrogenation of coal, also contain sulfur compounds which must be effectively removed. Thus, the need for fundamental research on the sulfur compounds that may be expected in petroleum and allied products is becoming greater as the industry is forced to call upon all available resources to meet the demand for petroleum products. In recognition of this need, the Bureau of Mines has inaugurated a long-range program assigned to furnish fundamental data concerning the presence, characteristics, and effects of sulfur compounds in petroleum and its products."

Dec 1, 1946

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Determine the appropriate spacing and alarm levels for carbon monoxide and smoke sensors used for fire detection in underground coal mine conveyor belt entries. Background Fire represents one of the most severe hazards in underground coal mines. Early-warning fire detection in underground coal mines is essential to successfully implement and execute evacuation and control measures. Both carbon monoxide (CO) and smoke sensors have the ability to provide reliable early-warning capability, provided that they are spaced properly and set at the appropriate alarm levels. The U.S. Bureau of Mines conducted a series of large-scale experiments where a small coal fire was used to ignite a conveyor belt at air velocities of 0.76 to 6.1 m/s. The test configuration was purposely designed to model a worst-case fire scenario for fires that develop within conveyor belt entries in underground coal mines. During the tests, CO and smoke levels were continuously measured to determine alarm times and alarm levels as the fire intensity progressed. The data from these tests indicated that for a given sensor spacing, the time to reach a preset alarm threshold depends upon the belt entry air velocity and cross-sectional area. Analysis of this data resulted in the equations and nomographs for CO and smoke sensor spacing, and alarm levels contained in Bureau of Mines RI 9380, "Fire Detection for Conveyor Belt Entries."

Jan 1, 1993

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By J. G. Kirby

According to the Bureau of Mines annual survey, as of January 1, 1954 there were 337 refineries with a total daily crude-oil throughput capacity of 8,006,897 barrels. The total daily capacity increased 368,236 barrels during the year while the total number of refineries declined 6. The capacity of the average refinery to process crude oil therefore increased during 1953 from 22,270 barrels to 23,759. With the exception of the Texas Inland, all refining districts reported gains in the installed capacity for the year, the largest being the Louisiana Gulf Coast with an increase of 20 percent. A total of 397,500 barrels of additional crude oil capacity was reported as under construction January 1, 1954. Accounting for 129,500 barrels of this total are facilities for 3 new refineries in North Dakota, 2 in Washington and I each in Ohio and Utah. Equipment being installed to replace existing units, totaled 180,750 barrels daily.

Jan 1, 1954

By Richard O. Kneisley

Microseismic activity observed in both the laboratory and underground indicates that a quiet period, associated with the closure of existing fractures and strongly influenced by coal seam microstructure, occurs prior to coal bumps. Field studies conclude that coal mine bumps occur against a background of this so-called microseismic calm. This Bureau of Mines report summarizes microseismic activity associated with face bumps and floor bursts in a deep, western U.S. coal mine. Results conclude that while bumps are often accompanied by panel-wide increases in microseismic activity, bumps are not only preceded by a localized decrease in activity, but occur within these quiet zones. The results of this study concluded that microseismic activity may be applicable to the global detection of potential bump-prone zones, but that future studies are necessary to confirm these findings and to improve the techniques for evaluating stress control effectiveness.

Jan 1, 1989

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By Connie S. Musulin

Radon concentrations in shallow uranium mines such as the Bureau of Mines experimental research mine are affected by barometric pressure changes. The radon concentrations show a significant correlation with absolute pressure; but over a period of days, a steady rise or fall in barometric pressure will result in noncorrelation of data. Fan shutdowns also affect radon concentrations, and an equation was derived to determine the time required for the radon concentration to return to normal after a fan shutdown, whether the ventilation is blowing or exhausting.

Jan 1, 1982

By M. L. Williams

In recent years the use of visual aids has expanded the? field of safety education. This is a modern adaptation of a method employed in ancient times, when simple paintings and drawings were the only means of recording current events. In its present application, visual aid employs sound and silent motion pictures, stripfilms, lantern slides, descriptive posters, and color. According to Roberts,3/ "Visual education is a method of imparting information which is based on the psychological principle that one has a better conception of the thing he sees than of the thing he reads about or hears discussed." Dent4/ further defines visual aid as "all the materials used to facilitate the understanding of' the written or spoken word."

Jan 1, 1951

By G. Molinda, D. Dolinar

Each year, about 2,000 falls of supported roof occur in the more than 800 underground U.S. coal mines. Therefore to help improve the design of primary support systems, the National Institute for Occupational Safety and Health (NIOSH) conducted a nationwide study of roof falls in over 2,500 km of roadways at 37 coal mines. Information on the roof falls as well as other geotechnical, mining, geologic and roof bolting factors were collected and quantified Then a multi variate statistical analysis was conducted on the data with the roof fall rate being the outcome variable The results were used to derive preliminary design guidelines for predicting the roof bolt length, capacity, and pattern required to effectively reduce the roof fall rate. The equations are fairly limited by a relatively high statistical variance in the data. Also reported is a recent survey of U.S roof bolt manufacturers that shows a significant change in bolt types used over the last ten years.

By Lloyd A. Morley, Alan M. Christman

PART A. ELECTRICAL EQUIPMENT – GENERAL Paragraph 1. Electrical Equipment; Examination. All electric equipment shall be examined, tested, and properly main¬tained by a qualified person to assure safe operating conditions. The examinations and tests shall be performed at intervals not exceeding six (6) months unless otherwise specified in Parts A, B, C, D, and E. When a potentially dangerous condition is found on electric equipment, such equipment shall be removed from service until such condition is corrected. A record of such examinations shall be kept and made available to an authorized representative of the Secretary and to the authorized repre¬sentative of the miners in such mine. Each item of major equipment, in¬cluding substations, switchgear, load centers, and so forth except powered hand tools, shall be recorded separately. The record of such examination shall include all dangerous conditions found, corrective action taken, and name of examiner, and shall be signed by the person responsible for main¬taining the equipment in safe operating condition, who shall also be a qualified person. Paragraph 2. Electrical Work; Qualified Personnel. No electrical work shall be performed on electrical distribution circuits or equipment, except by a qualified person or by a person trained to perform electrical work and to maintain electrical equipment under the direct supervision of a qualified person. Disconnecting devices shall be locked out and prominently tagged by the persons who perform such work, except that in cases where locking out is not possible, such devices shall be opened and prominently tagged by such persons. Locks and tags shall be removed only by the persons who installed them or, if such persons are

Jan 1, 1976

By Martin S. Oudenhoven

This report describes the results of a Bureau of Mines investigation in which the stress concentrations and distributions caused by inclusions in a strained elastic plate were determined, Finite element analyses were made for 168 models containing single inclusions of elliptical, ovaloidal, and rectangular shape. The variables studied included: horizontal-to-vertical loading ratios, (Sh/Sv) of 0,0.33,0.5, and 1.0; width-to-height ratios (w/h), of 0.25, 0.5, 2, and 4; and Young's modulus of inclusion to Young?s modulus of plate ratios (K ratios) of 0.33, 0.5, 2.0, and 5.0. The results show that the theory for elliptical inclusions can accurately predict the average stress along the x and y axes of symmetry for circular, ovaloidal, and rectangular inclusions from the width-to-height and K ratios. The actual inclusion shape was insignificant, suggesting that the average stresses in other inclusions of irregular shape (orebodies) can be estimated with the theory for an elliptical inclusion. An application of this technique to mining problems is presented. The stresses in the elliptical inclusions were uniform throughout the inclusion for all the models studied.

Jan 1, 1972

By Rex D. Thomas

Concentration of the kerogen (organic material) in oil shale was accomplished by centrifuging after pretreating the oil shale with carbonic acid to remove the carbonates and pretreatment with sodium hydroxide (pH 11.5) to remove the claylike minerals. Analysis of the materials obtained showed that the concentrations of organic sulfur and organic nitrogen compounds were not affected by centrifuging. These compounds are evenly distributed in the kerogen and are not strongly bound to the mineral constituents. Organic oxygen compounds, however, were concentrated in the light fraction. These compounds are more closely associated with the kerogen and are not bound to the mineral constituents. Iron compounds other than pyrite apparently are closely associated with the organic material.

Jan 1, 1970

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat, area of northeastern Colorado. Sample 31310 was taken from the Continental Oi1 Co.'s well Briggs No. 1 which came in on September 27,7.931, with a maximum production of 940 barrels per day. Sample 31311 was taken from the Reiter-Foster Oil Co.'s well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day. These two samples of crude oil are typical "intermediate base" crude oils according to the classification defined by Smith and Lane. The characteristics of these two samples, as shown by the Hempel analyses, indicate that they are almost identical. They have a very low sulphur content, and the residuum has a low carbon-residue content which would indicate that they are excellent crude oils for refining. Crude oils yielding a residuum which has a carbon-residue content of 4 per cent or less usually make good material for the manufacture of cylinder stocks. The pour points of the samples and the cloud test of the fractions obtained from the vacuum distillation indicate that the Greasewood Flat oil contains considerable wax. The high wax content would cause some difficulty in transmitting this oil through a pipe fine during extreme cold weather.

Jan 1, 1932

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion - exchange X- ray spectrographic method was developed and evaluated for determining trace amounts of cobalt and nickel in high - purity tungsten and tungsten trioxide . The sensitivity for both cobalt and nickel is in the range from 0.2 to 0.5 μg ( 0.04 to 0.1 ppm , based on 5 gram samples ) . Accuracy at the 5 to 20 μg level is ±10 percent of the amount present . Approximately 16 hours elapsed time is required for analysis

Jan 1, 1963