Search Documents

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By Lucia Kuizon

The Morongo Wilderness Study Area (WSA) is in south central San Bernardino County, California. U.S. Bureau of Mines examined the area during the fall of 1983. No mines, prospects, leases, or mining claims were found in the WSA. There are no known mineral deposits within the study area boundaries. Sand and gravel in the area is suitable for many types of construction uses, but similar and larger deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By Claude W. Sill

In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of. Tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate; It seemed likely that the, same general procedure could be used in determining semimicro quantities of uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant its turn permits the use of the very stable indicator, ferroin, with its sharp color.., change and exactly reproducible blanks. Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Gleu. The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months.

Jan 1, 1952

By David Schlain

"IntroductionThe purpose of this investigation was to study the characteristics of the high-acid electrolytic manganese cell with the idea of fitting it into one of the flow sheets being worked out by the Metallurgical Division of the Bureau of Mines for the recovery of manganese from low-grade domestic ores.In construction, the high-acid cell 3/ differs from the low-acid type in that the cathode and anode compartments are separated by a diaphragm of relatively low porosity, such as alundum. This is necessary because in the high-acid cell the two electrolytes are circulated separately. The anolyte is 15 to 30 percent H2SO4. The catholyte consists of a solution of ammonium sulfate and manganese sulfate with a OH of 4 to 3. The only mixing of electrolytes is that resulting from flow through the diaphragms. In the low-acid cell the two electrolytes are not circulated separately and do not differ so widely in hydrogen-ion concentration. Hence, the canvas diaphragm is sufficient.During operation of the cell, manganese is deposited on the cathode, and sulfuric acid is produced in the anode compartments. Various other reactions take place in the cell. There is considerable decomposition of water; hydrogen is evolved at the cathode, and oxygen is liberated at the anode. When lead anodes are used, some hydrated oxides of manganese are formed at the anodes. The quantity of oxides formed is not as great as it is in the low-acid cell, because fewer Mn++ reach the vicinity of the anodes."

Jul 1, 1942

By J. E. Conley

[Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft-paper industry, especially in Lie South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far re¬moved from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4?10H20), which must be dried or dehydrated in order to most consumer requirements. The waters of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery or production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.]

Jan 1, 1936

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX D DEVELOPMENT AND EXPERIMENTAL VERIFICATION OF ACOUSTIC SEAL CHECKER THEORY 1. Introduction In Section 7 of the report the acoustic seal checker concept was described in a general manner and the parameters which affect the signal level at the microphone were discussed briefly. In this appendix the theoretical basis will be presented and the experimental program described which permitted the extension of the theory into practice. The basic goal of the acoustic seal checker is to relate the reduction in sound pressure level to the size of the residual hole in the fly ash barrier. The smallest hole size that may be measured is determined by the signal to noise ratio, where the noise in this case includes the ambient noise in the mine, the internal microphone noise and the sound transmitted from the acoustic source via the flanking paths through corridors adjacent to the one being sealed. The latter source of noise can be discriminated against, at the expense of increased complexity of the acoustic system, by employing a pulsed source and pulse gating of the microphone signal set to accept sound via the barrier path and to reject the delayed flanking path signals. In order that the acoustic system be insensitive to precise source and microphone location and to permit assessment of system performance on an acoustic power flow basis, a broad frequency band of pseudo-random noise is emitted by the loudspeaker source. The preferred frequency range must be determined, the advantage of a directive source must be assessed, and the necessity

Jan 1, 1973

By G. W. Jones, R. E. Kennedy

"INTRODUCTION Information relative to the ignition temperatures of acetylene and acetylene-air mixtures has become of particular interest recently due to a number of explosions that have occurred in 500-pound, double-rated, medium-pressure acetylene generators in shipyards on the West coast. Various suggestions have been made as to the causes of these explosions prominent among which has been that air finds its way into the acetylene generators during abnormal operation or that air remains in the carbide hopper of the generator following the purging and charging operations.This raises the question as to how and to what extent the presence of small percentages of air in acetylene affects the ease of ignition of such mixtures at the various operating pressures of the acetylene generators. The range of operating pressures in the 500-pound, double-rated generators involved in the explosions may vary from below atmospheric to 15 pounds gage.The present report gives the results of an investigation made to determine the effects of pressure on the ignition temperature of pure acetylene and of acetylene containing varying percentages of air:EXPERIMENTAL Apparatus A preliminary investigation showed that a heated quartz surface gave lower ignition temperatures than other material tested.A ""hot-spot"" method of ignition was found desirable in the case of the acetylene mixtures since the violence of the explosions was reduced by keeping most of the test mixtures at room temperature. Explosive violence was reduced further by using an ignition tube 17 mm. or less in diameter."

Mar 1, 1945

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950

By L. C. IlsLey

A list of permissible mine equipment approved by the Bureau of Mines before January 1, 1940, was published in Bureau of Mines Information Circu- lar 71103. Information Circular 71584, published as a supplement thereto, listed equipment approved during the calendar year 1940. The present list contains the information given in those two circulars, as well as approvals issued during the calendar year 1941. It embraces electrically operated air compressors, coal drills, conveyors and loading machines, electrical equipment for mine fans, mining machines and trucks, mine pumps, rock- dust distributors, room hoists, storage-battery gathering and haulage locomotives, storage-battery power trucks and shuttle cars, mine telephones, junction and distribution boxes, electric cap lamps, flame safety lamps, electric hand and trip lamps, electric flood lamps, flashlights, methane detectors, and single- and multiple-shot blasting units. The equipment listed is not approved by the Bureau of Mines until found by inspection and test to comply with minimum standards of safety as outlined in "schedules" prepared upon the basis of many years of ex- perience in dealing with safety problems confronting the coal-mining in- dustry. The use of such equipment in mines that are known to be gassy,. as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that are available for reducing explosion and other hazards incidental to coal mining.

Apr 1, 1942

By Michael J. Sapko, Samuel P. Harteis, Eric S. Weiss

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL’s Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal’s ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

By T. L. Joseph

"In the January 3 issue of Iron Trade Review, Sweetser2, in referring to the problem of coke combustibility, points out that, ""Someone should formulate a rule for the rate of flow of coke through the zone of coke combustion that now appears to be confined to a comparatively restricted volume in front of the tuyeres,"" In formulating such a rule it is necessary to distinguish clearly between combustibility, a property of the fuel, and rate of combustion, which is determined by the rate at which air is supplied to the fuel bed. The rate of carbon gasified at the tuyeres of a blast furnace is independent of coke combusti-bility. A fast-burning coke will burn in a more restricted volume than a slow-burning coke, but both types of fuel will be consumed at rates determined by the supply of oxygen,A number of the definitions of combustibility that have appeared in technical literature relate more closely to rate of combustion than to combustibility. Perrott and Kinney) have correctly defined it as follows: ""Combustibility of coke from the standpoint of its use in, the blast furnace is inversely proportional to the mean rate of gasification per unit volume of the combustion zone, assuming other factors remain constant,"" Combustibility of coke refers therefore to those properties that determine the size or extent of the combustion zone. Relative differences in these properties can be measured by the depth of the fuel bed required to convert oxygen from the air into carbon monoxide."

May 1, 1924

As part of the U.S. Bureau of Mines (USBM) program to characterize subsidence this combination of software and hardware has been used to remotely monitor overburden response to longwall mining. Background The principle of time domain reflectometry (TDR) is being used by the USBM to monitor strata displacements induced by mining. This capability has been enhanced by the availability of cable testers with serial communication modules that allow users to get TDR records in digital form. Actual field installations involve coaxial cables that arc hundreds of meters long, and the many records obtained when monitoring such long cables on a daily basis motivated development of software to view interactively and compare waveforms and to analyze signature changes. Time domain reflectometry (TDR) was developed in the 1960's as a method to locate discontinuities in coaxial transmission cables. The concept has been extended to measurement of properties of materials into which probes are embedded, such as water content of soil, and evaluation of coaxial cable dielectric behavior. This technique was adapted by the USBM in 1975 for use in checking the movement of rock during underground mining. Coaxial cables are grouted into a rock mass that is expected to cave, and progressive rock movement causes the cable to deform. Consequently, there is a progressive change in cable electrical properties that produces changes in TDR pulse reflection signatures. TDR technology has been advanced by Northwestern University to the point where it is now possible to distinguish shear deformation from tensile deformation, and to quantify rock mass displacements, by analyzing these changes in TDR signatures.

Jan 1, 1993

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By Gene Asai

Properties obtained for columbium carbide-carbon castings ranging in car-bon content from 12 to 17 weight-percent were compared with those of hot-pressed composites of similar composition. The properties were oxidation resistance in static air between 500° and 700° C, linear thermal expansion between 20° and 2,400° C, electrical resistivity between 20° and 1,500° C; microhardness between 20° and 1,500° C, and modulus of rupture between 1,300° and 1,800° C. CbC-C castings differed markedly from hot-pressed material with respect to microstructure, electrical resistivity, and modulus of rupture, but behaved quite similarly with respect to oxidation resistance, thermal expansion, and hot hardness. In oxidation resistance, thermal expansion, and hot hardness both materials were independent of carbon content. Both castings and hot-pressed composites oxidize rapidly in air above 600° C, have thermal expansion coefficients very similar to columbium metal, and the logarithm of the hardness decreases linearly with increasing temperature. The microstructures of hot-pressed composites contained varying amounts of graphite in a CbC matrix but did not contain significant amounts of a eutectic structure present in all castings, nor did they contain graphite needles which were present in the hypereutectic castings. The higher electrical resistivity of hypereutectic castings over hypereutectic hot pressings was attributed to the presence of highly oriented graphite needles in the castings. The modulus of rupture of castings was 1-1/2 to 2 times that of hot-pressed composites. Both materials displayed bend ductility above 1,800° C.

Jan 1, 1971

By A. G. Starliper

Research was conducted by the Bureau of Mines to determine feasible roasting methods for the removal and the recovery of germanium, cadmium, and lead as enriched fractions from sphalerite concentrates. The two types of roasting processes studied were: (1) Batch, with a stationary bed, and (2) continuous, with a suspended bed, Results indicated that either method gave satisfactory metallurgical recoveries} but the continuous process is recommended because of inherent advantages. Final products were enriched fractions that could be treated by conventional methods for production of metallic germanium, cadmium, and lead. In the batch process, the concentrates were placed in a large tube furnace and heated at 1,080° C, an average of 3 hours. During the heating period, inert, reducing} or sulfur-laden gases were passed over the stationary charge to convey the sublimed metal sulfides from the hot portion of the tube to a lower temperature condensing zone at the end of the tube, where the metal sulfides were collected on baffles and recovered. In the batch and fluidizing roasting processes alike, the gases passed over or through the charge and served only as carriers for the sublimates and as suspension media in fluidization roasting. Since both processes depended on the volatilization, at relatively high vapor pressures, of the sulfides of germanium, cadmium, and lead, it was imperative that very little oxygen come in contact with the charge to alter the sulfide minerals. Germanium has a high affinity for oxygen, but in this instance it was buffered by being in solid solution in zinc sulfide.

Jan 1, 1961

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By Árpád B. Palotás, Adel F. Sarofim, John B. Vander Sande, Paolo Ciambelli, Lenore Rainey

"The evolution during oxidation of the internal structure of soot and carbon black particles was studied using high-resolution transmission electron microscopy (HRTEM) and an image analysis system. Increasing ordering to the carbon structure with increasing oxidation is observed. Measures of the increased order are increases in the fractional coverage of a cross section of the particles with a layered structure, a decrease in the mean interlayer spacing, and a decrease in the spread of the interlayer spacing. The changing structure of the carbon black impacts its properties, such as the rate of oxidation.There is considerable interest in the study of the structural changes of carbonaceous materials as a function of oxidation. Davis et al.1 measured the variation of carbon dioxide surface area of various coals as a function of residence time in a flow reactor. HRTEM measurements revealed that crystallite dimensions and interlayer spacings are altered by combustion. Ishiguro et al.2 showed that oxidation alters the structure of diesel soot. The aim of our current research is to develop a better understanding of the microstructural reordering of carbon blacks with implications to their properties. The carbon blacks used in this research have already been studied and their reactivities as a function of oxidation measured.3The methodology used in this work has already been described in detail elsewhere.4 This paper presents an application to quantify the structural changes of carbon black particles as a function of oxidation and graphitization. The technique used is based on the use of HRTEM (high-resolution transmission electron microscopy) and computational image analysis.It is well-known that carbonaceous materials like graphite, soots, coals, chars, etc., possess characteristic structural appearances which can vary from mostly random or amorphous to a perfectly ordered graphitic crystalline structure. The carbon structure has been variously described as turbostratic5 or as crumpled sheets6 to indicate that parallel layering, reminiscent of graphite, is observed over dimensions of nanometers but that these planes or crystallites show disorder over larger scales. The degree of order of such structures is strongly dependent on the thermal treatment of the material as well as the composition of the source of the carbonaceous material. The value of electron micros¬copy in studying the morphology of such materials has been well established,2,7,8 although only a few attempts toward quantification have been made.The sample observed was carbon black CB330 from De¬gussa. One set of carbon black samples were oxidized in a thermo-gravimetric analyzer (TGA) in air at 575 0C, so that the conversion varied from 0 to 96%. Another set of carbon black samples were graphitized (Graphpac-GB by ALLTECH) and then oxidized in the TGA at 680 °C until 92% burnout was reached. The latter samples are called GB 0% and GB 92%, respectively.For the HRTEM observation a small portion of each sample was ultrasonically dispersed in ethanol. The suspension was deposited dropwise on a copper TEM grid coated with a lacey carbon film. The examination of the samples was carried out on areas that extend over the holes in the supporting film in order to avoid interference from the amorphous carbon background film An oriented gold crystal was used as a calibration standard and subjected to the same techniques as the carbon black samples."

Jan 1, 1998

By E. R. Maize, R. D. Currie

"Good ventilation is one of the first requisites in the safe and efficient operation of a coal mine. If a mine is gassy, the uninterrupted circulation of an adequate supply of fresh air is imperative if that mine is to operate with a relative degree of safety. That ventilation is not •only a safety consideration, but is an extremely important economic factor is shown by the fact that in many mines 50 per cent of the total power cost is for ventilation.The system used in the Graceton Coal & Coke Co. mine, Graceton, Pa., is believed to be unusual in many ways. Its application in this mine has re¬sulted in good ventilation of the working faces, no interruption to the venti¬lating current through the use of doors. a large- portion of the air circulated by the fan reaching the working places, low velocity air currents on traveling and haulage ways, low water gage and power consumption of the fan, and well-ventilated gob areas.This investigation was made possible through the courtesy of W. H. Robertson, mine superintendent. Fred Roberts, mining engineer, and Floyd Phillippi, mine foreman, assisted in the collection of information.The Graceton mine is a slope, opening the Upper Freeport or E bed, on the Pennsylvania Railroad about midway between Blairsville and Indiana at Graceton, Indiana County, Pa. The production is approximately 1,000 tons of coal per day and about 170 men are employed underground. The mine is considered gassy and was found to be liberating approximately 300,000 cubic feet of methane in 24 hours. The return airways terminate at a circular, concrete lined shaft 12 feet in diameter and about 115 feet deep at which is the exhaust fan.Mining is done by a block system with flat or level entries turned off the main slope at intervals of 1,350 feet, off which the butt headings are turned up the grade parallel to the slope. Rooms, which are about 225 feet long and 12 feet wide, are turned off the butt headings on 80-foot centers, leaving a block about 68 feet thick between rooms.Haulage on the main slope is by rope, with the hoist on the surface. This hoist is electrically driven through a 500-h.p., 2,300-volt motor. The rope used in this haulage is 1-1/8 inches in diameter. There are five electric trolley locomotives - one 10-ton and four 6-ton - which do all of the hauling in the flat and butt entries.Before it is blasted all of the solid coal and as much of the pillar coal as can be cut with safety is undercut by permissible mining machines. Shooting is done by shot firers who use permissible explosives, electric detonators, and dry-cell, nonpermissible batteries.In rooms where conditions are normal, timbering consists of two rows of posts on 4-foot centers. Posts are required to be within 6 feet of the face in machine-cut places and within 3 feet of the face in hand-mined places. Timbering on entries, where required, is of two types: a bar hitched into the ribs and supported by the coal, or 3-piece sets. The legs of the 3- piece sets used on the slope are set well back into the rib to prevent their being. knocked out by a wreck."

May 1, 1932

By R. Karl Zipf, Christopher Mark

Highwall mining continues to grow in importance as a coal production method from U.S. surface mines. It may account for as much as 4% of the total U.S. coal production, according to one recent estimate. Analysis of Mine Safety and Health Administration (MSHA) accident and injury statistics shows that, overall, highwall mining has maintained an admirable safety record. Its fatality and injury rates are comparable to those for other surface mining methods, and are significantly lower than those for underground mining. No mining method is risk free, however. Highwall mining injuries have been associated with handling materials, slips and falls, machinery, powered haulage, and other types of incidents. But perhaps the greatest risk, to both personnel and equipment, is from ground control. The two most significant ground control hazards are rock falls from the highwall and equipment entrapment underground. Highwall Stability Ensuring highwall stability through proper ground control engineering is of paramount importance to safe highwall mining operations. The only fatality to occur during the last five years at a highwall mining operation was due to highwall collapse. There have also been numerous near-misses, several of which have involved extensive damage to equipment. In the central Appalachians, where the majority of highwall mining occurs in the U.S., hillseams are the most prominent geologic structures that affect highwall stability. Hillseams (or mountain cracks) are near vertical fractures in the rock that are formed in response to natural weathering and erosion of hillsides. They extend hundreds of feet down from the surface. They typically run parallel to the hillside, but they can also extend across narrow points or ridge lines. The hazard arises when rock slabs that form along the hillseams detach and fall away from the highwall face (See Figure 1). [ ] Unfortunately, it is impossible to control the location of hillseams or reliably detect their presence within a highwall. There are, however, a number of measures that can be taken to minimize the risk of failure associated with hillseams: Planning-Most operators choose to skip those areas of the highwall where a prominent hillseam daylights (See Figure 2). Existence of such areas is known for several weeks in advance of highwall mining; therefore, planning engineers can adjust the layout of highwall mining panels to locate barrier pillars within areas of questionable highwall stability. [ ] Inspection and monitoring-Daily inspection of the benches above the active highwall mining area is a prudent precautionary measure. A crack in a bench immediately above a highwall miner is shown in Figure 3. Simple displacement monitors may be useful for detecting movement along cracks that may precede a significant life-threatening failure. New tools, such as slope monitoring radar, may also prove useful in detecting motion of the rock slopes above active highwall mining operations. Good blasting practice-Most surface coal miners in the central Appalachians use pre-splitting and the familiar halfbarrels are routinely seen throughout the pits. Shorter delays along the face and longer delays between rows can direct more of the blast force parallel to the face, potentially doing less damage to the wall rock. In addition to pre-splitting, decreasing the burden, spacing and charge weight in drill holes close to the highwall will also decrease damage to the wall rock. Decreasing the highwall slope angle-Decreasing the highwall slope angle from 90° (vertical) to 70°-80°, especially in areas of known hillseam concentration, could eliminate the hillseam hazard (See Figure 4). Angled highwalls are routinely employed in many Midwestern surface mines and in some

Four actual coal mine waters were used in various phases of the research program. All were from the Sewickley Creek area In Westmoreland County, Pennsylvania. The BCR designations, site locations, and nature of the mine water samples are described briefly in the following paragraphs.

Jan 1, 1971