Search Documents

By Norman G. Foster

The mass spectra of four tertiary butyl substituted thiophenes are reported. A comparison and contrast with earlier structure correlations made by API-RP48 mass spectroscopists is presented. The fragmentation routes of these types of molecules are discussed and explained in terms of existing theories in mass spectrometry. Low ionization voltage data are presented to support the mechanistic picture developed. Structures are inferred about some of the ions, and these are correlated with existing theories. Metastable peaks in the spectra are used to support the fragmentation paths. The presence of doubly charged ions in the spectra is noted and the possible implications toward mechanisms discussed. The general picture of simple, small fragments leaving the ion moiety upon further fragmentation is developed in detail. Some suggestions are presented for further work utilizing isotopically labeled molecules to establish firmly the general picture of fragmentations of the alkylthiophenes.

Jan 1, 1966

By Frank J. Wiebelt

As a result of the examination of many copper-zinc properties in the West Belt area of California, nine were chosen for exploration projects by the Bureau of Mines. This was part of the Bureau's wartime mineral-development program aimed at maintaining production of essential metals and increasing ore reserves. The properties explored were the El Dorado, El Dorado County; Copper Hill, Newton, and Gray House, Amador County; Constellation, North Keystone, and Collier, Calaveras County; and American Eagle and Akoz, Mariposa County. In addition to surface sampling and mapping, 41 holes, aggregating 18,134 linear feet, were diamond-drilled. Detailed results of the work done on all properties except the El Dorado and Akoz are given in this report. The El Dorado and Akoz were discussed in Reports of Investigations 3896 and 4144, respectively. Figure 1 is an index map showing the location of the mines covered in this publication.

Jan 1, 1951

By Kenneth M. Earl

This report describes the results of a field study conducted by the Bureau of Mines during 1956 and 1957 on manganese-and iron-bearing mineral deposits in the southern district of Aroostook County, Maine. The work was undertaken to determine the extent of deposits largely concealed under glacial drift and to obtain subsurface samples for manganese mineral identification and research in ore dressing and extractive metallurgy. The investigation was confined to the Westford Hill-Daggett Hill area in Hodgdon Township and to the Stewart prospects and vicinity in Linneus Township. Over 50 magnetic anomalies were mapped by magnetometric surveys in the Westford Hill-Daggett Hill area, Hodgdon Township. The largest anomaly, as outlined by the 1,000-gamma contour, indicates a deposit 3,200 feet long with a maximum width of 350 feet. The smallest anomaly measures about 10 feet wide by 25 feet long.

Jan 1, 1962

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By A. L. Engel

This report is a compilation of results of preliminary tests on scheelite (tungsten) ores and tailings. These investigations were made to assist in establishing satisfactory treatment methods for small-scale concentrator operations, or to indicate a. method for conserving previously lost mineral values in old tailings, if possible. A discussion of test procedures is included, as it was felt that this would add to understanding the results reported under the several projects. The treatment of scheelite ores has become more or less standardized. Important differences occur in textures of ores from various mining districts. However, and this must be considered when planning ore-dressing operations. In most of the present investigations, only a limited amount of work was done, usually just enough to answer a specific question in regard to a particular ore or concerning local conditions. Two methods of treatment included gravity concentration, magnetic separation, and flotation.

Jan 1, 1952

By A. D. Hahn

This report describes reconnaissance by the Federal Bureau of Mines of titanium-bearing sandstone in Kemper County, Miss. The purpose was to determine the ilmenite, rutile, and associated heavy-mineral content of black-sand-bearing Eocene deltaic formations" The investigation was part of a survey of titanium resources of the United States. Ilmenite (FeTi03), an iron-titanium oxide, is the major titanium-bearing mineral consumed in the titanium pigment industry. Rutile (Ti02), titanium oxide, is used mainly in producing welding-rod coatings and titanium metal. The fieldwork was conducted during the first half of November 1959. Seven holes, totaling 304 feet of bore, from which 64 samples of cuttings were taken, were drilled in the north-central part of the county; and two holes, totaling 172 feet of bore, from which 34 samples of cuttings were taken, were drilled in the southeastern part.

Jan 1, 1961

By John W. Finch

The Secretary of the Interior acting through the Bureau of Mines and the Geological Survey is authorized by the Strategic Materials (Public No. 117 - 76th Cong., Chapter 190 1st Sess.) to make investigation concerning essential minerals of which the quantities or grades obtainable from known domestic sources are inadequate. The Bureau of Mines, in carrying out its part of this program, may investigate deposits of such minerals in whatever manner may be necessary, in order to determine (1) the extent and quality of the are, (2) the most suitable method of mining and beneficiating it, and (3) the cost at which it may be produced. The essential objective in doing these things is to determine where and how supplies of minerals and metals of which domestic production is usually inadequate might be obtained in a national emergency, even though at higher cost than usual.

Jan 1, 1939

By Donald O. Capstick

In 1481, U.S. Bureau of Mines personnel conducted a survey of mines, prospects, and mineral resources in the Table Mountain RARE II area. There are no mines or active prospects in the study area. One prospect in the study area, the Waterfall Prospect, is estimated to contain 480 tons (440 t) of indicated subeconomic tungsten resources averaging about 0.18 percent tungsten trioxide (W03). Other tungsten occurrences are at the Stevens Prospect, just northwest of the area. Stone and sand and gravel deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 4,400-acre Table Mountain study area is 13 mi (21 km) southwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir wilderness adjoins the study area on the southwest (fig. 1).

Jan 1, 1982

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By Ronald F. Balazik

The introduction of "high-tech" materials such as new polymer composites presents significant competitive challenges and opportunities in conventional mineral markets. Moreover, rapid advances in materials science are critical to the resolution of important economic and strategic issues, including national competitiveness and import dependence. This Bureau of Mines study examines the displacement of conventional nonfuel mineral materials by certain new materials, specifically advanced plastics and ceramics. Analyses of substitution by plastics are conducted for five major U.S. industrial sectors: motor vehicle manufacturing, aerospace applications, building and construction, packaging, and heavy machinery production. Based on interviews with more than 60 scientists, executives, and other professionals engaged in materials development and sales, forecasts of substitution by plastics during the 1990's are made for aluminum, steel, and glass. In addition to these forecasts, study findings identify key factors that will influence the emergence of advanced materials in the next decade.

Jan 1, 1987

By Dennis Cox, Stephen P. Signer, Joanne Johnston

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to (1) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

In Maryland, coal mining is confined to Garrett County and the western portion of Allegany .County. Terrain in both counties is predominately level with rolling hills; state law prohibits surface mining in steep slope areas. The Conemaugh and Allegany geologic formations contain five major minable fields or basins. These include: Upper Youghiogheny, Lower Youghiogheny, Castleman, Upper Potomac, and Georges Creek. Maryland's coal reserves are estimated to exceed one billion tons. Approximately 490 million tons of bituminous coal are considered recoverable using conventional mining methods. After World War 11, deep mining declined in Maryland, and by 1977 surface mining accounted for 91 percent of the total production. Since then, production at underground mines has recovered, accounting for 69 percent of the coal production in 1991. Maryland's permanent regulatory program was fully approved February 18, 1982. Its Abandoned Mine Land Program was approved June 16,1982.

Jan 1, 1992

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By Rose L. Ballard

This chapter summarizes data on crude non fuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal non fuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production, The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1986

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing. the stage of measurement used in this chapter is what is normally termed ?mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may he measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982