Search Documents

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

By James R. Jones

"The General Leasing Law, which provides for the leasing of deposits of coal, oil, oil shale, gas, phosphate, and sodium in public lands, was approved February 25, 1920.One of the outstanding features of this legislation is the fact that it opens for prospecting and exploitation lands and deposits which have been withdrawn from public use, some of them for several years, pending enactment of legislation better fitted to control the mining and utilization of the particular mineral deposits referred to. These lands are not only made available to the public, but they are opened up under a system which defines better than was ever done in the pas the rights which may be acquired under it.The oil operator, for example, under this legislation will know definitely the extent of the rights he has acquired, as well as the legal conditions under which his expensive drilling and other work of exploration are to be conducted. No longer will he be harassed by the possibility that while he is spending his capital in drilling operations in an effort to make a discovery of oil, his legal rights be contested, in which event the superiority of his claim can only be upheld -- if at all -- after long and expensive litigation. By the same token the coal operator will now be free from the embarrassing restrictions of the old coal-land laws respecting the amount of such land which may be purchased by one person.At the same time that these advantages are being enjoyed by the operators, the public will be guarded against wasteful methods of drilling and mining the oil and gas, and coal deposits, and the other mineral substances enumerated in the act, to the end that these products of Nature, which can not be replaced, may be utilized with a minimum of loss."

Mar 1, 1920

By C. V. Davis

In the lnvestlg::ìt1on of mAthods for aSS8.7ing platin",. conducted by the Bureau ot MinAs, reoent experiments have d~velopad tha~ with ce..tain orei, especially when thr, quantity Of platinum 1s eonlidarablfl, nit'!le acid w111 not etfßct a iepard-Han of platinum and pa11adium. 'lhe following m;lthod has been found to be accurate and to reiu1 t in a complete S''lun''ation of' th~3:l metals. It is therefo 1" '!eeommei:ed that 1 t ba followed rath::r- than the method of separation with nitrio acid, givèn in Technical Pape'! 270.* At line 22, pagi 14, of that paper, bAglnnlng with ~tarm th,~ metals '.'ith dilute¡ nitrio acid," strikE out the rest of the paragraph, and substttutt~ the pro_t cedure g1 ven below. ?lunder and Thuringer.. have developed mnt¡iods for th"i sflparation of palladium from all the platinum metals exoept platinum bj m ,ans of dlmethy- 19lyoxlme. They state that the~ is no action for several hours if an excess of dimeth¡lglyoxime is added to an aqueous solution of ohloroplatinic acid in the cold, alio that only on boiling is the platinum pTecipi ated ¡~d than only PST't of the platinum i srenoved from the sUut1on. They found that palladium 1s p~ecipi tated quati tat! vely in the oold as (CaH 4N40 Pd) which is insoluble tn water, dilute hydroohlorio acid, dilute acetIc aofd or in 50~ ethyl alcbhol. All of their pT'90ipi tations we~p Carl". ied out ~hile the solutions were being heated. This caused a pal"tia~recipltation of the platinum along wi th the

May 1, 1922

By John Gross

In connection with some investigations being made at '!'he Ra.re uid Precious 1ets.ls Station of the U, S. Bu.rea.u of Mines, at Reno, Nev., on the precipitation of gol'i and silver from cyanide solutions, it wa.s sug­ gested tnat the use of acetylene for this purpose be investigated, A pa.tent was iss·.ied to Fre<!.erick W. Martin and Frederick Stl1.bbs in 1900 covering the precipitation of precious metals from cyanide solu­tions by acetylene, The acetylene used in the tests described below wa3 made f'rom a. corr.:nercial cal ci \'!Z:l carbid.e, A r..umber of exper:me11. +,s rezul ted in more or lP.ss ccmplete pree;p1tatien of silver, -but 1n no case was a11Y gold precipitated. As silver acetylide, obtained by precipitatir.g the silver from an ar:::ncni'i\.Ca.l so1ut1on of silver n,. tra.te by acetylene, is yellowish white, esn:, solu'.)le in cyanide and hlghly explosive, and the pr9cip1tate ob­tain£ frcvm the cy'31lide sclutions was black, not tlubla L., cyanide and not explooive, it 'Na.s deid-,d. to ir.·.restigate the na.tur.e of the slJ.ver pre­cipit.te !rem the cy;r:iide solu·t:i.i,ns, !n prepa;.•i::lg a lge (!\,wrttity ,:f the preci-pi tte 1 t. wa, fo·und that a.fter c,:.\i;:1 ete prEc"'.pi tat ion cf the eil ver the !IOl ution con ta.ined soluble eulphic.e • Thia p:!:'O'lided a el f!W "lt·d. a.ft er apr,ropri-9.te tests the preeipita.te VIO,I proved to 'be ailver sulphide.

Apr 1, 1922

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By H. E. Sanford

"INTRODUCTION Of the occupations in and about coal mines, those of the haulage crews are among the most hazardous. Statistics indicate that the second largest number of fatalities about coal mines occurs during haulage operations and through the use or misuse of haulage equipment. Despite the fact that relatively few coal-mine employees are engaged continuously at haulage operations, approximately 20 percent of all coal-mine fatalities are attributable to haulage.Most of the hazards in haulage operations could be very greatly reduced if more serious consideration were given to the problems of the haulage crews and if sincere efforts were made to reduce the hazards. Underground haulage is similar in many respects to railroading; yet, railroading is now considered one of the safest of occupations a distinction that has been attained only by honest effort and whole-hearted cooperation on the part of all concerned. Underground haulage is also similar to street and highway operation and has in it some of the difficulties encountered in the reduction of traffic accidents the seriousness of which has not by any means been con¬trolled as yet, notwithstanding the fact that much effort has been expended through a multiplicity of laws, ordinance regulation, etc., as well as by thousands of enforcement agencies and officers.The men working on the locomotives are among the most important members of a coal-mine organization; without skilled haulage employees, the production of coal would be greatly retarded. Their jobs, particularly the job as brakeman, require physical endurance, agility, and mental and physical alertness; in thin coal beds, especially where the roof is not brushed and the coal is loaded into mine cars by hand, the need for these qualifications is greatly increased."

May 1, 1948

By Fred N. Kissell

In This Chapter [Early indicators of a gas problem How the methane hazard is reduced Ventilation principles for gassy tunnels Monitoring for gas Eliminating ignition sources and The all-important human factors component] This chapter gives guidelines for preventing methane gas explosions during tunnel construction. Emphasis is placed on assessing the hazard potential, on ventilation principles, and on monitoring for gas. The chapter also emphasizes the importance of human factors in reducing explosion risk. Ensuring safe conditions is much more than just good engineering design. It also involves the every-day vigilance of those working underground. This does not imply that the engineering design can be ignored, only that the job of providing safe conditions has just begun with design. EARLY INDICATORS OF A GAS PROBLEM For the engineer planning a tunnel project, reliable early indicators of methane are scarce. How-ever, the local geology can often provide some information.2 Carbonaceous rocks and tar sands are a likely methane source. Gas is also a distinct possibility if it is known to be present else-where in the same sequence of geologic formations. Swampy areas, sewerage systems, and landfills are also candidates because the decomposition of organic materials produces methane. The gas in a tunnel can originate in the strata being excavated, or it can migrate a considerable distance from adjacent strata. Test borings at the project site can also serve as initial indicators of gas. Methane has no odor, but may be emitted along with gases that do. If gas is emitted from the borehole, a sample may be collected by inserting a tube into the hole as far as possible and pumping the gas out. The gas sample should be collected in a sampling bag or canister for later analysis by a chemical laboratory.3

Jan 6, 2006

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

1. Introduction This document represents Part II of our final report on the development of a "Remote Sealing System for Extinguishing Coal Mine Fires. " It is a technical report which summarizes the results of system development and field demonstration. Part I of this two - part final report is an Operator&apos;s Manual for the application of the Remote Sealing System to a coal mine fire. 1.1 Background When coal mine fires go out of control and can no longer be fought directly, the standard fire fighting technique is to construct air-tight seals in the mine passages leading to the fire area so&apos;--,that the oxygen supply to the fire is". cut off. Ultimately, it is desirable to isolate the fire zone in such a way that normal operations can resume in the remainder of the mine. The construction of seals in the- mine causes the atmosphere to pass through a toxic and explosive phase. Explosions, if they occur, are not only hazardous to the men working at the sealing operation, but can also undo much of the sealing work which has already been accomplished. Sealing of passageways surrounding the fire zone from within the mine is extremely difficult and dangerous. Methods for direct sealing are detailed in "Control of Mine Fires&apos;. 1 An alternative to this approach is the technique of remote sealing. This involves drilling boreholes which intersect the mine passages at the locations where the desired seals are to be constructed. The seals are then constructed by pouring material down the borehole and filling a segment of the passage from bottom to top. During this operation, there are no personnel in the mine, all operations taking place on the ground surface.

Jan 1, 1973

By Maria I. De Rosa

The U.S. Department of Energy Pittsburgh Research Center2 conducted experiments with mine conveyor belt samples in a 20-L furnace and in a laboratory fire tunnel to measure and compare the major toxic gas concentrations evolved during the combustion of the materials. The toxic gas concentrations, measured simultaneously through a multiport sampling device and treated as yield values, included hydrogen chloride (HO), hydrogen cyanide (HeN), oxides of nitrogen (NO, treated as NO), and carbon monoxide (CO). The data obtained from the two experimental systems were in good agreement. Correlations were developed for the toxic gas yields as a function of the percentage of chlorine (for HO gas), nitrogen (for HCN and NO, gases), and carbon (for CO gas) contained in the original materials. The toxic gas yields were also used to calculate a toxicity index (TI) parameter to assess the potential gas toxicity of belt materials during a fire. Furthermore, the TI and the mass loss burning rate values were used to calculate a toxicity hazard (TH) parameter to estimate the toxic gas hazard produced by a burning belt in a ventilated system. Results show that polyvinyl chloride (PVC) belts released higher HC1 concentrations because of the higher chlorine content; styrene-butadiene rubber (SBR) belts released higher CO, HCN, and NOz concentrations because of the higher carbon and nitrogen contents. The TI&apos;s, however, were greater for the PVC belts due primarily to the higher levels of HC1 produced. The fire tunnel data indicate that the SBR belts can bum with higher mass loss rates than the PVC belts, resulting in a potentially higher toxic hazard (higher TH values) even though their TI values were lower than those of the PVC belts.

To develop a quick, safe, and effective method that allows workers at mineral processing operations to clean their dust-soiled clothing periodically throughout the workday. Background Reducing workers&apos; respirable dust exposure to silica and other harmful dusts and contaminants is an ongoing goal in the U.S. mining industry. One area of known worker exposure is from contaminated work clothes. A U.S. Bureau of Mines report documented a number of cases where a tenfold increase in a worker&apos;s dust exposure was measured from contaminated work clothes. In these cases, the dust emitted from clothing caused the worker&apos;s dust exposure to exceed the permissible exposure limit in less than 2 hours. The most effective way to eliminate this dust source is to have workers clean or change their work clothes. There are two federal regulations that impact the clothes-cleaning process. The first states that at no time shall compressed air be directed toward a person, but that when compressed air is used, then all necessary precautions shall be taken to protect persons from injury. The second regulation states that compressed air should only be used for cleaning purposes when it is less than 30 psi and used along with personal protective equipment. For the mining industry, by default, the only approved method to perform clothes cleaning is to have workers vacuum their clothes using a HEPA filter system. This is very difficult and time-consuming and, in most instances, not very effective. Most workers would prefer to use a single compressed air hose to blow dust from their work clothes. However, not only is this method prohibited by law, it usually creates a significant dust cloud in the work environment and contaminates coworkers.

May 1, 2005

By W. M. Weigel

"Sand is one of the commonest materials for industrial use, not only as a building material, but in many industrial processes. The general name applies to all grades, from the comparatively impure, unsorted product used in concrete, to especially sized products of extreme chemical purity. Various definitions have been proposed, all more or less open to objection, as they fail to cover special applications. One is: ""Sand - The fine granular material naturally or artificially produced by the disintegration or crushing of rock or slag"". This does not fit the definition of sand as understood by geologists, who consider sand only as a naturally formed product. Another is: ""Sand - The fine granular material naturally produced by the disintegration of rock"". This does not take the chemical com-position into account, and for practically all uses, except in concrete and plaster products, a material composed predominantly of silica or rather quarts is implied.Sand for special purposes usually requires different methods of preparation from those where the ordinary mixture of sizes as naturally occurring are suitable. One of the classes requiring the most uniformly sized grains is sand blast sand.Sand Blast SandThe use of the sand blast has increased rapidly during the past few years. It was formerly used almost entirely in the foundry to clean and remove inequalities from rough castings. This is still the most important application, but in addition, it is now employed for the removal of paint from old surfaces, carving and engraving on stone and marble, glass cutting, cleaning or renovating the rails of stone and brick buildings that have become discolored, preparing the surface of metals for the electrolytic bath, putting the final finish to metal surfaces, and has even been proposed as a means of channeling or cutting out blocks of stone in the quarry."

Jun 1, 1924

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By John T. Kuo

The miner&apos;s seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner&apos;s seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By D. N. Nilsen

The Bureau of Mines is developing a method to recover Ni, Co, and Cu from laterites containing less than 1.2 pct Ni and 0.25 pct Co. The method consists of the following basic unit operations: (1) reduction roasting, (2) leaching, (3) solvent extraction, and (4) electrowinning. The method reflects three Bureau of Mines objectives: (1) recovery of critical minerals that are domestically in short supply from low-grade domestic laterites, (2) lower processing energy requirements, and (3) solution recycling. This report deals with the extraction of cobalt and the preparation of a suitable cobalt electrolyte by solvent extraction from liquor produced by this method. Nickel and copper are coextracted with LIX64N from an ammoniacal ammonium sulfate leach liquor containing about 1.00 g/l Ni, 0.30 g/l Co, 0.03 g/l Cu, and 0.02 g/l Zn. Cobalt (III) in the nickel-copper barren raffinate is reduced to cobalt (II) with cobalt metal. Reduction of cobalt (III) to cobalt (II) greatly aids subsequent extraction. Commercially available XI-51 extracts about 94 pct of the cobalt from the treated raffinate in one stage in a laboratory mixer-settler continuous circuit. Ammonia loaded on the solvent is removed in two washing steps. About 94 pct of the cobalt then is stripped from the XI-51 in one stage with spent cobalt electrolyte containing about 77 g/l Co and 18 g/l sulfuric acid (H2S04), Electrolytes containing less H2S04 also may be used. Preliminary data indicate that coextracted zinc may be removed from pregnant cobalt eletrolyte containing 3 g/l or less H2S04 with di-(2 ethylhexyl) phosphoric acid (D2EHPA).

Jan 1, 1980

By Christopher Van Dyke, Edward L. Petsonk, Knox Van Dyke, Vincent Castranova, Ji-Hee Kang, William Pailes

"INTRODUCTIONPlatelet-activating factor (P AF) has been shown to mediate a broad range of biologic activities (1). Chemical analysis has shown that PAF is a glycerophospholipid with a choline polar head group, an ester-linked acyl chain at the second carbon of the glycerol backbone, and an ether linkage at the first carbon. The alkyl group attached to the first carbon can exist in a variety of chain lengths, with the C16 and C18 forms predominant in humans. The structure of P AF has been identified as 1-0-alkyl-2-acetyl-sn-glycerol-3-phosphorylcholine (2,3).PAF can be released from a variety of cell types, such as basophils, neutrophils, and alveolar macrophages ( 4-6). Stimuli for the release of P AF include calcium ionophore, phorbol esters, chemotactic agents, and zymosan. In addition, endotoxin has been shown to be a potent stimulant of P AF release from alveolar macrophages (7).P AF has been shown to have a number of pulmonary effects. It has been associated with asthma since it can cause contraction of pulmonary tissue (8) and leukotriene secretion from leukocytes (9) and induce airway constriction when inhaled by humans (10). In addition, PAF is a potent chemoattractant and can cause migration ofneutrophils into the airspaces of the lungs (11,12). Endotoxin is a lipopolysaccharide-protein complex derived from the cell walls of gram-negative bacteria. I.PS is the lipopolysaccharide portion of endotoxin. LPS contains four covalently joined subunits: lipid A, 3-deoxyoctonate, a core polysaccharide moiety, and an 0-specific antigenic polysaccharide side chain. Rough LPS contains no 0-antigen side chain. The liP.id A portion of LPS has been associated with most of the biolQgic effects of endotoxin (13). This lipid A subunit consists of a D-glucosamine disaccharide backbone substituted with four fatty acid side chains. Endotoxin is found in a wide variety of occupational settings associated with organic dusts derived from plants or animals, such as cotton, cereal grains, silage, rice, and poultry (14-18). In addition, airborne endotoxin has been found in sewage treatment plants, composting plants, offices with contaminated humidifiers, and showers or saunas (19-22)."

Jan 1, 1990

By Boyd Guthrie

Methods of distilling topped crude oils and distillates under vacuum, accompanied by good fractionation, have taken a place of major importance in the refining industry. In the refining of petroleum products it is generally desirable to produce a distillate of good quality, and this objective is attained by fractionation of a high degree. The laboratory and commercial practice have proved that by varying the amount of fractionation the quality of the distillate can be changed, and refiners are cognizant of the advantages of good fractionation. Distillation under high vacuum, however, is a relatively new practice in petroleum refining, and only during the last few years has there been an indication that this method may become a general practice in the industry. Vacuum distillation offers many advantages over older methods of distilling petroleum products. Vacuum combined with steam distillation, for example, is replacing straight-steam distillation because the quality of the products of vacuum and steam distillation surpasses that of those produced by straight-steam distillation. Although the injection of varying amounts of steam in a vacuum unit is common practice, the amount of steam used is becoming loss as the vacuum within the unit is increased. This report describes the construction of a visible-action laboratory batch still and fractionating column and gives certain data pertaining to the operation of the apparatus under vacuum for the production of lubricating distillates. The apparatus was designed and built to produce lubricating distillates under as nearly ideal conditions as possible, in order that a subsequent study of the characteristics of the distillates could be made. For example, a study could be made of the distillates obtained up to the point of cracking of the charge if a topped crude were charged to the still; if the still was used as a rerun unit for lubricating distillates a study of nearly the entire charge could be made. Only topped crude has been charged to the still so far, and therefore this paper is limited to the results obtained from the distillation of such a charge. The results so far obtained indicate that such an apparatus is valuable in a study of different crude petroleums as sources of lubricating distillates.

Jan 1, 1932

By L. M. Chan, D. H. Carlson, J. H. Johnson

"This paper discusses the evaluation and application of a portable parked-vehicle tailpipe emissions measurement apparatus (EMA). The EMA consists of an exhaust dilution system and a portable instrument package. The EMA instantaneously dilutes and cools a sample of exhaust with compressed nitrogen or air at a known dilution ratio, thereby presenting it to instruments as it is presented to personnel in the surrounding environment. The operating principles and governing equations of the EMA are presented.A computational method is presented to determine the engine operating and performance parameters from the exhaust CO2 concentrations along with an assumed engine overall volumetric efficiency and brake specific fuel consumption. The parameters determined are fuel / air ratio, mass flow rates of fuel, air and exhaust emissions, and engine brake torque and horsepower. These calculated engine parameters are used to characterize engine load when performing EMA in-field tailpipe sampling without a dynamometer, and to detect deteriorated engines.Evaluations of the EMA by comparison of diesel tailpipe measurements with those made using laboratory-grade instruments showed that the EMA measurements are accurate and reproducible. The results also show that the EMA is capable of detecting emission concentration changes resulting from engine faults. Calculated engine operating and performance parameters correlate and compare well with laboratory-measured values.The EMA in-field engine loading and tailpipe sampling procedures for parked vehicles are presented, and results of the EMA field measurements are also presented. Low coefficients of variation for repeat EMA tailpipe measurements on diesel-powered haulage vehicles in four underground mines indicate that the EMA in-field engine loading and tailpipe sampling procedures are reproducible.An analysis of EMA tailpipe measurements for three haulage vehicles in one mine shows that the EMA can: 1) identify haulage vehicles that emit excessively high pollutant concentrations, and 2) provide data needed to evaluate and determine the efficiency and effectiveness of tailpipe emission control devices.Finally, recommendations for a proposed commercial EMA system are presented. This commercial system would overcome many of the adverse features of the prototype EMA used in these tests."

Mar 1, 1992

By Harry Freund, Kenneth H. Hammill, Francis C. Bissonnette

"Gallic acid is a sensitive, stable, colorimetric reagent for the determination of tantalum in the range of 2 to 40 µ g.Ta/ml. The method consists of the fusion of tantalum oxide with potassium pyrosulfate and solution of the cooled melt in saturated ammonium oxalate, followed by development of a yellow complex with an ethanolic solution of gallic acid. The tantalum-gallic acid complex absorbs over a broad region in the blue and near ultraviolet. Adverse effects due to interfering ions and solution conditions, such as oxalate concentration and pH, can be minimized by a suitable choice of wave length.by a suitable choice of wave length.A new and sensitive colorimetric method is provided that has been used successfully at the Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines for determining minor amounts of tantalum.INTRODUCTIONThe development of corrosion-resistant alloys at the Northwest Electrodevelopment Laboratory prompted a review of the analytical chemistry of columbium (niobium) and tantahnn. Not only are these elements difficult to determine in small amounts, but tantalum especially lacks both sensitive and characteristic color reactions. Various phenolic compounds have been suggested as colorimetric reagents for tantalum, Quentin and Wagner (10, p. 24B) 1/ recommend the use of tannin. The use of pyrogallol was suggested originally by Krivoshlykov (6, pp. 59-60), whose method recently has been subject to a number of modifications (3, pp. 249-254; 5, pp. 1340-1344; 1, pp. 1803-18oi; 4, pp. 345-350). The yellow coloration produced by pyrocatechol in an oxalate solution containing tantalum may also be used to estimate tantalum ( 11, pp, ll-1-4-148) . The use of hydrogen peroxide has been recommended also (7, pp. 164-165; 9, pp. 926-931).Aside from a lack of specificity and sensitivity, the major failing of phenolic reagents is their susceptibility to air oxidation. The oxidation products are highly colored and absorb in the same spectral region as the tantalum complex. Holding reductants are not completely satisfactory in minimizing this effect. Increasing the acidity, while retarding the oxidation, has an adverse effect on the tantalum sensitivity."

Sep 1, 1956

"Minimizing Particle Contamination During Generation of Fresh Dust for Inhalation Studies J. Abraham, MS, Mechanical and Aerospace Engineering, West Virginia University, 1995Correlating Lung Crackle Using Holographic Interferometry Ali Afshari, MS, West Virginia University, 1989Effect of Bit Wear on Dust Generation Mudassar Ahmad, MS, West Virginia University, 1992 The Effect of Surfactants on Suppression of Non-Wettable Particles Ali Alaboyun, MS, Mineral Engineering, The Pennsylvania State University, 1989 Geochemical Characterization of Kerogens, Shales, and Coal Refuse Associated with Allegheny Formation of Cases of Northern West Virginia Dick Andre, MS, West Virginia University, 1987Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment Indranil R. Bardhan, MEM Report, The Pennsylvania State University, 1992Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment I. Bardhan, R. V. Ramani, and J.M. Mutmansky, Mining Engineering, The Pennsylvania State University, University Park, PA, Final Report to the U.S. Bureau of Mines, April, 1994Particle Concentrations in a Hazelton Inhalation Chamber Shahram Bavani, MS, West Virginia University, 1985Use and Potential of Lazer Holographic Interferometry and Subsidence Model- Study of an Underground Room and Pillar Mine Richard Begley, MS, West Virginia University, 1984Development of a Mechanistic Model for Prediction of Subsidence in a Longwall Mine Richard Begley, PhD, West Virginia University, 1990Redesign of Micro-Orifice Uniform Deposit Impactor Steve Behm, MS, University of Minnesota, 1991Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle, MS, The Pennsylvania State University, 1996Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle and R.-V. Ramani, The Pennsylvania State University, University Park, PA, Final Report, September 9, 1996A Fracture Mechanics Study of Crack Propagation Mechanism in Coal: The Mechanics of Fine Fragment Formation Z.T. Bieniawski and R. Karl Zipf, Jr., Mining Engineering Department, The Pennsylvania State University, University Park, PA. Final Report, October l, 1988A Mathematical Model for the Prediction of Ambient Dust Concentrations in Mine Atmospheres R. Bhaskar, MS, Mining Engineering and Operations Research, The Pennsylvania State University, 1984Spatial and Temporal Behavior of Dust in Mines-Theoretical and Experimental Studies –R. Bhaskar, PhD, Mining Engineering, The Pennsylvania State University, 1987"

Jan 1, 1998