Search Documents

By C. M. McCulloch, Maurice Deul

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By Howard C. Pettibone

Mine safety personnel reported occurrences of excessive "glove-fingering" and other problems with resin-grouted roof bolt installa tions. To study these problems, the Bureau of Mines designed a test plan to (1) obtain baseline information on several resin cartridges and (2) investigate the variables involved in the installation of a resin bolt. Three brands of resin representative of the industry in January 1983 were selected for cartridge evaluation. The installation variables selected for study were the method of installation, the hole depth, and the hole annulus. These variables were studied by installing a series of bolts in concrete blocks using different values for each variable. Results of the research show overspinning the resin may cause problems, but they can be avoided by using the spin times recommended by manufac-turers. Excessive glove-fingering is not a problem if the manufacturer-recommended installation procedures are followed.

Jan 1, 1987

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

By Wilder D. Foster

In estimating the hazardous qualities of a dusty atmosphere it is frequently desirable to determine the composition of the air-borne dust. Samples collected from ledges or from the rock itself are Likely to be unsatisfactory for this purpose owing to the possibilities of differential disintegration of the rock and of variations in settling rates of the different components of the minerals. It may be necessary, therefore, to collect samples of dust from the air. Samples collected from the air may be analyzed chemically, by X-ray diffraction, and by the petrographic microscope. Chemical methods are unsatisfactory owing to the small samples usually available and to the limitations and complexities of: present methods. X-ray technique requires expensive apparatus not ordinarily available except in research laboratories. Owing to the simplicity and rapidity of petrographic is examination of atmospheric mineral dusts, it was considered worthy of further study.

Jan 1, 1938

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965

By Wilder D. Foster

In estimating the hazardous qualities of a dusty atmosphere it is frequently desirable to determine the composition of the air-borne dust. Samples collected from ledges or from the rock itself are likely to be unsatisfactory for this purpose owing to the possibilities of differential disintegration of the rock and of variations in settling rates of the different components of the minerals. It may be necessary, therefore, to collect samples of dust from the air. Samples collected from the air may be analyzed chemically, by X-ray diffraction, and by the petrogrephic microscope. Chemical methods are unsatisfactory owing to the small samples usually available and to the limitations and complexities of present methods. X-ray technique requires expensive apparatus not ordinarily available except in research laboratories. Owing to the simplicity and rapidity of petrographic examination of atmospheric mineral dusts, it was considered worthy of further study.

Jan 1, 1938

By Marvin L. Whisman

This report describes the preparation of tritium-labeled organic compounds to be used by the Federal Bureau of Mines in studying the role of certain gasoline constituents in gum-forming mechanisms. The gasoline constituents that have been investigated boil within a range of approximately 90 to 230° C. and can be classified as paraffins. naphthenes, olefins, diolefins, monocyclic aromatics, polycyclic aromatics, and organic sulfur, nitrogen,: and oxygen compounds. The technique of Wilzbach has been applied to more than 50 samples. Purification techniques have been developed that accomplish rapid and effective purification as well as removal of labile tritium in a one-step operation. Data are presented to show the rate of exchange between tritium and hydrogen that can be expected for a variety of compounds common to a full-boiling-range gasoline. These values should be useful to other investigators using tracer programs involving tritium labeled compounds.

Jan 1, 1961

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By Jack I. Paige

The devitrification of lithium silicate glasses was studied to determine the effect of annealing temperature, composition, and additives on nucleation and crystallization. High-purity glasses, prepared from reagent-grade chemicals, had close to optical quality when prepared by a vacuum induction melting method developed during this research, The progress of devitrification was traced by differential thermal analysis and thermal expansion for those lithium metasilicate-silica compositions containing 80 to 90 percent silica. Microscopic studies of glasses partially devitrified at various temperatures and annealing times indicated that the primary initial mode of formation of individual crystals ,vas from densely crystalline zones that filled in as crystallization advanced Of the additives tested, calcium, potassium, and sodium helped promote devitrification with the least cracking or surface deformation. Tin oxide was most effective in reducing volume contrast ion during devitrification, but was not ClS effective in preventing cracking as calcium or potassium additions.

Jan 1, 1965

By Charles D. Litton

A new prototype ionization-attachment fire detector was developed by the Bureau of Mines for detecting combustion-generated submicrometer particulates. It is much more sensitive than the conventional ionization smoke detector, and it has the following added features: 1. A primary charging current of unipolar air ions is generated by a gold-coated, radioactive center electrode of a cylindrical diode. 2. Submicrometer particulates are flowed axially through the unipolar cloud where they acquire charge. The charged particles impinge upon a third electrode, located downstream, resulting in a current which is directly proportional to the particulate concentration. 3. Additional electrodes analyze the particulates in terms of their mobility and thus determine their size distribution. 4. A filter and cyclone assembly protect the ionization chamber against ambient dust. An analysis of conventional ionization smoke detector performance is also presented in terms of source strength, chamber geometry, and applied potential.

Jan 1, 1977

By E. R. Bauer

Noise-induced hearing loss (NIHL) continues to be a concern of the mining industry. A new noise standard (30 CFR, Part 62) is aimed at reducing NIHL in mining through engineering and administrative noise controls. However, the difficulty and expense of implementing engineering controls can make administrative controls an attractive alternative for reducing worker noise exposure. Over the last three years, the National Institute for Occupational Safety and Health (NIOSH) has conducted worker noise exposure surveys in underground and surface coal mines and in coal preparation plants. The surveys revealed numerous possible administrative controls and an approach to implementation and analysis. The surveys have shown that worker dosimetry, time-motion studies and equipment noise profiling are important aspects of effectively utilizing administrative controls. A description of the approach for selecting, implementing and evaluating administrative controls and a list of possible administrative controls are reported.

Jan 1, 2007

By Michael G. Zabetakis, Glenn H. Damon, Joseph A. Herickes

The flammability and explosibility of unsymmetrical dimethylhydrazine ( UDMH ) were investigated by the Federal Bureau of Mines to evaluate hazards associated with commercial application of this material as a missile fuel . This program included the following determinations : 1. Temperature limits of flammability in air at one atmosphere pressure ; 2. limits of flammability at selected elevated temperatures and pressures ; 3. 4 . 5. spontaneous ignition temperature in air at one atmosphere and at 200 pressure per square inch gage ( p.s.i.g. ) initial pressure ; spontaneous decomposition temperatures in nitrogen at one atmosphere and at 200 p.s.i.g .; shock sensitivity over a temperature range from about ( ca. ) 25 ° to 50 ° C .; 6. shock sensitivity of reference propellants ( hydrazine , nitromethane , methyl acetylene , etc. ) ; 7 . shock sensitivity of UDMH plus small amounts of selected metal catalysts . Part of the corresponding data was obtained for a mixture of unsymmetrical - dimethylhydrazine and diethylenetriamine ( U - DETA) .

Jul 1, 1960

By Marvin L. Whisman

Several parameters controlling the reproducibility of tritium determina¬tion in organic compounds by liquid scintillation counting were evaluated by the Federal Bureau of Mines. These included optimum volume of scintillator solution for maximum counting efficiency, reproducibility of counting a sealed commercial standard and comparison with duplicate counts on laboratory-prepared samples. The error introduced by using microliter pipets, optical differences in counting vials, reproducibility of counting organic samples where quenching is a factor, reproducibility of counting laboratory-prepared samples with an added internal standard, optimum ratio of internal standard activity to sample activity, effect of sample volume upon counting efficiency, count rate at which coincidence losses become apparent, and reproducibility of organic compound radioassay by the standard addition technique are outlined. From the evaluation of these parameters, a technique that can be applied routinely to organic compounds containing tritium has been established, and details are included in this report.

Jan 1, 1961

By Mark S. Sanders

The purpose of the present study was to develop and test improved Type V workvests for use on dredge operations. The goal was to design workvests that would be more comfortable to wear, would interfere less with task performance, and would better meet the needs of dredge workers. It was hypothesized that by attaining these goals, the resulting vests would be worn more often and would be kept buckled more of the time than traditional vests. The study involved three major phases. In Phase I, visits were made to dredge operations and a definition of the problem was developed. Problems with current vests were identified and working conditions and tasks surveyed In Phase II, prototype vests were developed and laboratory tests were per-formed to assess comfort and interference. In Phase III, the prototypes were modified and field tested with actual dredge operators and workers.

Jan 1, 1985

By F. A. Rutledge

The Millet copper deposit is on the north shore of Iliamna Lake in southwestern Alaska. Copper mineralization occurs in a zone of altered limestone .adjacent to and intruded by a diorite porphyry with some diabase facies. During 1949 and 1950, the Bureau of Mines investigated this prospect as a part of the U. S. Department of the Interior program in Alaska for the development of critical and strategic minerals. Field work was begun August 8, 1949; it was recessed November 28, 1949, because of inclement weather. The work was resumed Nay 28, 1950, and completed July 3, 1950. The program of investigation by the Bureau of Nines included topographic surveying, machine and hand trenching, diamond drilling, and sampling the zones of mineralization. This report outlines the general geology of the area, gives a description of the deposit, and contains the factual data resulting from work by the Bureau of Mines.

Jan 1, 1952

By John S. Dunning

This is one of a. series of papers being prepared for and published by the United States Bureau of Mines, describing raining and milling methods at crushed-stone plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in man; instances cause embarrassment to individual producers as well as to the industry as a whole. However, operating costs are essential to technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that the scope of the cost tabulations shall not be misunderstood. This paper deals with the quarrying and crushing methods used at the Avon Mountain trap-rock quarry of the Atlas Sand, Gravel & Stone Co., in West Hartford, Conn.

Jan 1, 1936

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968

By Robert T. Mann

This paper is one of a series being prepared for and published by the United States Bureau of Mines on the quarrying, crushing, and grinding of limestone for cement manufacture. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total coats. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. B. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1933