Search Documents

By Howard C. Turnage, Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally of times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 2, 1983

By Hal H. Engel

This publication was written in response to numerous requests for information about the Federal Bureau of Mines' "Demonstrated Lecture on Flame Propagation and Permissible and Explosion-Proof Electrical Equipment." The requests came principally from: (1) Persons wanting to know more about the demonstration before requesting it for groups they represented; (2) persons wishing advance information to help publicize a meeting where the demonstration was to be given; and (3) members of audiences desiring something to help them remember the salient points, facts, and figures presented during the lecture and demonstration. The purpose of the demonstration that accompanies the lecture is to show: (1) Variations in flame speed and pressure at various percentages of flammable gas within the flammable range; (2) effect of flame speed on the "pressure piling" within the area confining the mixture; and (3) the application of flame speed and pressure piling to the combustion of surrounding gas and to the design and maintenance of electrical equipment used in hazardous locations.

Jan 1, 1960

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By E. S. Shedd

Misch metal was electrowon from a treated bastnasite concentrate in a REF3-LiF-BaF2 electrolyte at 950° C. The metal was prepared and tapped from a 1,000-ampere cell, and nearly 100-percent utilization of the rare-earth oxide was achieved. Prolonged operation in a smaller cell (40 amperes) indicated that the composition of the misch metal product was reasonably constant, and no significant increase of impurities, with the exception of carbon, was noted.

Jan 1, 1970

By F. E. Griffith

[Unquestionably mine fires new constitute one of the chief causes of sabotaging the effort to produce maximum quantities of mineral products essential to the prosecution of the war. This applies more particularly to coal than to noncoal mines, and presumably the main reason for this is the fact that coal production in maximum quantity is still very much a "must", while the demand for much of the product of noncoal mines has eased materially in recent months.]

Jan 1, 1944

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

The standard method of employing preliminary air-drying to determine the moisture in coal has been criticized with respect to the loss of heating value from excessive air-drying. By this method, the coal is air-dried at approximately 10-15° above room temperature with the loss in weight being less than 0.1 percent per hour, and then the residual moisture at 105°C is determined. The total moisture is calculated from these two values.

Feb 1, 1948

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 241,502 employees worked in surface mining locations in 2003, corresponding to 212,113 full-time equivalent (FTE) workers. • Surface employees accounted for 84.6% of all mining employees. • The majority of surface employees (73.7%; n = 177,927) were mine operator employees as opposed to contractor employees. • Stone operator employees comprised the greatest percentage (27.2%; n = 65,743) of surface employees.

Feb 1, 2005

By A. A. Giardini

This report represents the results of a literature study on boron nitride and related substances. The purpose of the study was to find Information that might be of value for production of a new, hard modification of boron nitride preferably in single crystal form. The report consists of a review of the major developments in boron nitride research, a discussion of the results, tabulations of physical and chemical properties;, conclusions drawn from the study, and a bibliography.

Jan 1, 1953

By Richard L. Lewis

This is a discussion of the application of the zonal harmonic series to problems involving dipole sources in the vicinity of spherical boundaries. The application of a formal zonal-harmonic series solution to directly obtain numerical results involves two distinct problems: namely, the convergence of the series solution and the accurate calculation of the special functions involved in the series solution. Some interesting techniques will be introduced which help to improve the convergence properties of the series solution.

Jan 1, 1973

By R. L. Montgomery

The literature has been surveyed and values recalculated for the heats and free energies of formation of solid rare-earth compounds at 298° K. In most instances it was necessary to estimate the entropies. Thermodynamic properties of aqueous rare-earth ions have also been calculated. INTRODUCTION The accumulation of thermochemical data on rare-earth compounds in recent years makes it possible to review the subject and to obtain more consistent and more reliable information than was available previously.

Jan 1, 1959

By Mark R. Pettitt

Noise surveys conducted in underground coal mines have consistently indicated that auger mining machines subject the operator and helpers to excessive noise exposure. The machine cutting heads have been identified as the primary noise source. This report documents the research program conducted to (1) investigate the nature of the cutting head noise problem, (2) develop noise control concepts, (3) devise in-mine survivable techniques to implement the noise control concepts, and (4) build and demonstrate prototype reduced-noise auger miner cutting heads. The dynamic forces generated during coal cutting by the brittle fracture of coal are predominently low frequency. The low-frequency (less than 1500 Hz) structural response of the cutting head, therefore, determines the noise radiated by the cutting head. The most feasible methods of reducing the cutting head low-frequency response are to increase both the structural stiffness and the low-frequency damping. A technique was devised to achieve these goals. The standard plate helix was replaced by a sand-filled hollow helix of triangular cross section, and the core diameter was increased with an attendant reduction in helix depth. Extended in-mine tests demonstrated the operational capability of the reduced-noise auger cutting heads. The simple noise control concepts are valid for all continuous miner cutting heads. The sand-filled hollow helix technique, which achieved a 10 dB(A) noise reduction for the auger, can be used on any helix-bearing Cutting head.

Jan 1, 1983

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By R. F. Tenney

This report has been prepared because little detailed information has been published on the production and use of anthracite producer gas for industrial-process and brick-kiln heating. To obtain this information, an investigation was conducted by the Federal Bureau of Mines in cooperation with a building-brick manufacturer (firing both periodic and tunnel kilns with anthracite producer gas) and with a manufacturer of anthracite-gas producers. In addition to a study of available plant records, 2 weeks was spent in systematic observation and measurement during regular operation of the Hazleton Brick Co. plant, Hazleton, Pa., in July 1953. This report presents the results of this investigation and a description of producer and periodic-kiln equipment, operating procedures, and labor requirements. A summary of the conditions of producer and kiln operation is given for the 2-week observation and for the 11 preceding months. The two 10-foot standard anthracite-gas producers consumed 301 tons of Rice and Buckwheat No. 1 anthracite, as delivered, averaging over 13,000 B.t.u. per dry pound during the 2-week period, with a producer hot-gas efficiency of 95 percent, at an average gas offtake temperature of 5400 F. The yield of gas5/ of 153 gross B.t.u. per cubic foot amounted to 140,000 cubic feet per ton of fuel as fired, or 73,500 cubic feet per kiln heating hour, which was sufficient for kiln requirements.

Jan 1, 1960

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine's investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By J. E. Tiffany, Z. C. Gaugler

An active list of permissible explosives was published in December 1943 as part of the Bureau of Mines Report of Investigations 3736 under the title "Active List of Permissible Explosives and Blasting Devices Approved Previous to June 30, 1943." This list included 180 brand names. Changes in the list that have been authorized to December 31, 1945, placed 10 additional brands of permissible explosives on the active permis- sible list as a result of tests and changes in brand names.. Twelve permis- sible explosives were transferred from the active. to the inactive list. The present list contains 178 brand names. The brand names of the permissible explosives placed on the active list are as follows: American 3-A By test. Apcol No. 1-B Do. Black Diamond No. 11-B DO. Black Diamond No. 55 DO. Coalite G-1 DO. Coelite K-1 Do. Do. Coalite L-1 Coalite IS-1 Columbia B-2 DO. By change in name. By test. Monobel AA The permissible explosives transferred from the active to the inactive list are as follows: Anthracite B, L. F. Big Red No. 8 Independent No. 1, L. F. Independent No. 2, L. F. Independent No. 3, L. F. Independent No. 4, L. F. Independent No. 5, L. F. Independent No. 9, L. F. Independent No. 9-C, L. F. Independent No. 10, L. F. Independent No. 11, L. F. King No. 9

Jul 1, 1946

By E. J. Gleim

Many people consider the mining of coal to be an extremely hazardous occupation; but it should be remembered that most large industries have to meet special conditions which, if not dealt with properly, might become hazards to life and property. Mining men may not always be fully aware that some practices and certain equipment that is incorrectly designed or maintained can lead to dangerous conditions. In endeavoring to help the coal-mining industry to prevent accidents and disasters, the Bureau of Mines has engaged in a program of education on conditions and practices that must be avoided. An effective way to teach safety is by visual demonstration. For example, it is generally known that certain kinds of electrical flashes have ignited explosive atmospheres in mines, but actually to see and hear explosions caused by electrical sparks of different size and character under laboratory control is likely to teach a much more emphatic and lasting lesson than would be learned by merely reading about them. The interest manifested by those who witness the demonstrations seems to prove that this is true. The purpose of the demonstrations is not to discourage the use of electricity in mines, but rather to indicate what types of equipment (including some generally regarded as harmless) can ignite gas and what safeguards have been developed to prevent such ignitions. It is hoped that this information will improve the ability of mining men to cope with underground hazards.

Jan 1, 1937

By John P. Capp

The feasibility of simultaneously burning several paths through a coalbed to develop a multiple path underground gasification system was investigated by the Bureau of Mines during two experiments, Boreholes were drilled through the overburden and into the coal and arranged in a circle approximately 50 feet from a central borehole. In the first experiment, in an area which had previously been hydraulically fractured,5 air was injected at the center borehole. The coal was ignited at the other boreholes and the fire fronts traveled toward the center, counter to the flow of air, to backward burn paths through the coalbed. Two paths were linked during the first 5 days of operation. The outlets of these two paths were throttled and air pressure was increased to maintain the flow of air, but no other linkages were made. Fourteen days after the two linkages these two paths were opened and gasification was carried on for 10 days, but with only moderate success. In an effort to overcome operating difficulties air was injected at the peripheral boreholes, and the gases were drawn off at the center borehole. Reversed flow operations continued for 12 days and two more paths linked. The heating value of the gas generally was higher than 100 British thermal units per standard cubic foot (B.t.u. per std. c.f.). Because only four of seven paths linked, however, the entire system could not be evaluated with respect to product-gas output and recovery of energy.

Jan 1, 1961