Search Documents

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general; the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By Lloyd Williams, R. E. Hershey, B. W. Gandrud

"1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come :from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sevanee has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although some coal has been produced from them.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on l,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed ·were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal are estimated in beds 28 inches and more 'thick. This recovery is based on total thickness of coal in the bed (less partings 3/8-inch thick or more), rather than on the thickness of the coal actually mined. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian Region. The combined weighted average recovery for the Sewanee and Battle Creek beds in Marion County, as determined by this investigation, is 60.9 percent. Based on this, the recoverable reserves of coal in Marion County are estimated at 34 million tons."

Oct 1, 1955

By B. W. Jong

As part of the Bureau of Mines program to develop substitutes for critical and strategic materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives and starting materials on the sintering and strength properties of sialon (silicon-aluminum-oxynitride) compositions fabricated by conventional pressing and sintering techniques. Sintering and MOR (modulus of rupture) data were developed for sialon compositions produced from three components, Si3N4, A1203, and AIN. When doped with Y203 to aid in sintering, the highest MOR values were obtained with compositions containing between 20 and 30 mole-pet (A1203 + AIN). The effect of the crystalline phase of the Si3N4 and Al203 used in the three-component system on MOR also was investigated. Alpha-Si3N4 and ?-A1203 were found to be the best starting materials. A sialon composed of 67.4 mole-pct a-Si3N4 plus 32.6 mole-pct (?-AI203 + AIN), doped with 5 wt pct Y203, had MOR values at 25°, 1,200°, and 1,400° C of 40,300, 40,300, and 31,100 psi, respectively. Samples of this composition doped with Gd203, MgO, Zr02, and ZrSi04 also were evaluated. The ZrSi04-doped sialon had higher MOR values than Gd203-, MgO-, and Zr02-doped materials but lower MOR values than the Y203-doped sialon. The MOR values of ZrSi04-doped sialons were 25,000 and 25,900 psi, respectively, at 25° and 1,400° C.

Jan 1, 1981

By Maurice Deul

A special short-term research project was initiated to develop plant design parameters for treating mine waters to yield an effluent acceptable for discharge into streams and a sludge amenable to effective and economic disposal. Neutralization was investigated to provide simple and direct treatment of ferruginous acid waters using lime; coarse limestone, and limestone followed by lime. Limestone treatment was accomplished using a small cement mixer as a simple reactor to provide abrasive agitation of limestone and mine water. Results from tests with nine mine waters encompassing a wide range of iron and acid concentrations showed that coarse limestone, one of the cheapest neutralizing agents known, is potentially useful for treating mine water discharges. However, process variables must be defined more completely before the practical applications and limitations of the process can be fully established. In all the tests a pH of >7.2 was obtained ultimately with limestone. Reaction time to reduce the iron content below 7 ppm in the water was dependent on the original ferrous iron concentration. For waters with high ferrous iron content, treatment with limestone followed by lime rapidly produced an acceptable treated water, Sludges with good settling and handling characteristics resulted when limestone was used for neutralization either alone or with subsequent treatment. Reaction rates are expressed graphically as pH change and iron depletion curves; characteristic solids settling curves are shown. The temperature dependency of ferrous iron oxidation was verified.

Jan 1, 1967

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By E. D. Eastman

The basic character of the free energy r data relating to water and the oxides of carbon makes it desirable that the most representative values that can be obtained should be constantly available. The calculations of Lewis and Randall3 retain much of their of original value, but appear to require some modification in the light of more recent work. This paper has been written to incorporate the newer information and to present some estimate of the reliability of the resulting figures. The data upon which the calculations are mainly based are, for these substances, the equilibrium constants of the various reactions involved. The original work relating to these equilibria has, been reviewed and, where possible, weighted to correspond with its probable reliability. The differences in the results of the present from the earlier calculations are partly the consequence of this appraisal and partly of the inclusion of more extensive data, as will be indicated in detail in the succeeding sections.

Jan 1, 1929

By E. C. Pattee

A mobile spectroscopic laboratory was completed by the Bureau of Mines in 195 to provide a rapid, inexpensive means of field testing samples for beryl¬lium and other associated metals of possible commercial importance. Spectro-copes have been used in laboratories for many years in various types of research and routine analyses, but this spectroscope is probably the first mobile unit. The laboratory provides for spectroscopic, radioactivity, fluorescent, and limited chemical tests of samples. The unit has been a valuable reconnaissance tool. It has been used to search for beryllium, cesium, columbium, tantalum, rubidium, and lithium in Idaho, Washington, and Montana. Several very low grade deposits of these elements were found, and occurrences of other important elements were identified; however, none are of economic importance. The spectroscope permits the detection of elements by analysis of visible light produced when elements in a small powdered sample are volatilized in an electric arc., A total of 70 elements can be detected; 29 can be detected at or below 0.01 percent, Electric power for the arc is supplied by a gasoline motor-driven generator, Equipment is housed in an aluminum van, mounted on a 4-wheel-drive vehicle for easy maneuverability on mountain roads, A trailer with crushing, pulverizing, and splitting equipment permits the reduction of samples to a small representative pulp.

Jan 1, 1963

By Vernon C. Davis

In initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining. The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost. This report, is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges. Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage. In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested. Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes. Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows paral-lel to one of the series of joint planes. Methods of detonation made little difference in breakage; but the milli-delay caps produced the best conditions for moving the broken rocks.

Jan 1, 1953

By V. M. Benson

A simplified, routine method for determining lithium in lithium-bearing rock is presented. The sample is decomposed by repeated treatments with nitric, hydrofluoric, and perchloric acids. Since this procedure does not appreciably dissolve beryl, interference by beryllium (the principal interfering cation) is minimized for most samples. The salts are brought into solution with water and enough citric acid-ammonium citrate buffer is added to make the final volumetric dilution 0.20 M with respect to citrate. The addition of citrate greatly reduces anion interference in the hydrogen-oxygen flame, slightly increases the intensity of the lithium 671 millimicron emission line, and reduces the effect of most of the interfering cations to the extent that analytical separations are not necessary. The accuracy of results of single determinations of lithium in a pegmatite containing spodumene, lithium-bearing mica, and beryl are approximately equal to that obtained by other flame methods, INTRODUCTION This investigation was undertaken in Bureau of Mines laboratories to develop a reliable, rapid, routine analytical method for determining lithium in lithium-bearing minerals. The requirements of the procedure were that the method should be applicable to the analysis of a variety of lithium-bearing ores and test products, and the results would be reasonably accurate for materials containing 0.05 to 8 percent Li20.

Jan 1, 1961

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By G. V. Sullivan, G. F. Workentine

Beneficiation studies were conducted by the Bureau of Mines on three samples of low- grade chromite - bearing material from the Stillwater complex of Montana . The objective of the study was to develop methods for recovering chromite from low- grade materials to improve the domestic reserve situation . Samples were obtained from the three largest deposits in the district , Mouat , Benbow , and Gish . The chromic oxide ( Cr₂ 0 ) content of the ore and of the chromite was about the same in each of the samples . The major gangue constituents ranged from clean olivine in the Mouat sample to such altered minerals as serpentine and talc in the Benbow and Gish samples . Tabling , flotation , high- tension electrostatic separation , and combinations of processes were applied to each ore . Treatment of the Mouat sample ( 9.95 percent Cr₂ 0 ) by high- tension electrostatic separation , a combination of tabling and high- tension electrostatic separation , and tabling with middling retreatment resulted in concentrates that graded 42.8 , 42.0 , and 40.7 percent Cr₂03 at chromium recoveries of 85 , 86 , and 84 percent , respectively . Other techniques were less selective . 2 The Benbow sample ( 7.75 percent Cr₂0 ) responded most selectively to tabling with middling retreatment and a combination of tabling and hightension electrostatic separation to produce concentrates of 40.1 and 39.5 percent Cr₂g with each process having a chromium 2 recovery of 69 percent . Response of the Gish sample ( 8.04 percent Cr₂03 ) to the various concentration techniques was about the same as that of the Benbow sample , but in general , somewhat less selective . A combination of tabling and high- tension electrostatic separation resulted in a concentrate that contained 71 percent The Mouat mine was reopened in 1953 when the American Chrome Co. contracted with the Federal Government to produce 900,000 tons of chromite concentrate . The ore , averaging 20.2 percent Cr₂03 , was treated by tabling to produce a 38.5 - percent Cr₂ O concentrate.

Jan 1, 1964

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

By J. R. Thoenen, J. L. Vallely, M. C. Malamphy

"SUMMARYMagnetic and gravimetric surveys wore conducted over an area of ap¬proximately 1,400 square miles in the bauxite district of central Arkansas. The primary purpose of these surveys was to discover any possible buried and hitherto unknown syenite masses favorable for the occurrence of bauxite and to determine the approximate position of the buried flanks of the known syenite masses which might offer conditions favorable for the discovery of new ore bodies.Those surveys indicated that the various syenite outcrops were domes or bosses on a large batholith and that ether similar domes occurred on the batholith but did net outcrop.Drilling on the local geophysical anomalies proved the presence of 10 buried domes, but only 2 of them were found to project above the upper surface of the Midway clays, a requisite of conditions favorable for the occurrence of bauxite ore bodies. The geophysical data indicated the approximate configuration of the buried flanks of the known syenite coutcrops, and the portions of these flanks that project above the Midway have now been outlined more accurately by drilling.The geophysical surveys have produced evidence permitting the elimi¬nation of a large area as unfavorable for the occurrence of bauxite.Magnetic surveys extending along the Midway-Wilcox contact from Gurdon, in Clark County, on the southwest to Searcy, in White County, on the northwest have proved the improbability of the existence of other syenite masses similar to those found in Pulaski and Saline Counties. A detailed magnetic survey of the Magnet Cove area in Hot Spring County has proved that the syenite mass exposed in that locality is an isolated intrusion and entirely unrelated to those of Pulaski and Saline Counties. This syenite mass does not occur under conditions believed to be favorable for the occurrence of bauxite."

Feb 1, 1945

By D. Harrington

The number of fatalities from mine explosions for the fiscal year 1945 dropped below that of the year before; continued improvement over the record of the years from 1940 to 1945 is hopeful, but the number of reported explosions has increased rather than diminished, and the number of victims claimed by explosions is often more definitely a factor of chance than forethought. Mine fires and explosions can be eliminated through the methods now well-known to those well-informed in matters pertaining to safety in mining but ignored by many coal-mine operators and employees who follow procedures of the past or their own short cuts, regardless of disasters that may result: Tried and proved safety measures for preventing mine fires and explosions have been recommended to the mining public repeatedly, yet only a relatively small but far-sighted minority have adopted these measures and made them a part of operating practice. That far more explosion disasters did not occur in 1945 is fortunate. In 1945 a coal-mine fire of electrical origin caused heavy loss of life, while several others from the same cause were controlled with but few fatalities; this hazard is now being curbed temporarily to some degree after the bad record of the two preceding years, but a real solution of the problem has not been reached, although cooperating committees trying to produce at least some answer have made progress.

Jan 1, 1946

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977

General economic conditions continued to improve in the second quarter of 1984 as real gross national product advanced at an annual rate of 7.5 percent (table 1). This followed an even larger first quarter annual rate increase of 10.1 percent. The slower second quarter growth was greeted as a sign that the economy is not over-heating. The signs of slowed growth in some sectors suggest that the recovery may continue well into 1985 without the inflation symptomatic of a rapid recovery. Most of the slowdown in growth was absorbed by business inventories, personal consumption of durable goods, and residential fixed investment. Business inventories grew by only 68 percent as much as in the first quarter, personal consumption for durable goods grew by 58 percent of the first quarter rate, and residential fixed investment slowed to only 44 percent of the first quarter growth. Sectors with accelerated growth in the second quarter included personal consumption of nondurable goods and of services, which increased at annual rates of 9.6 percent and 3.8 percent, respectively, and Federal purchases of goods and services, which increased at an annual rate of 47.9 percent.

Jan 1, 1984

By F. D. Everett

The Burgin shaft of Bear Creek Mining Co. near Eureka, Utah, was sunk during 1956 and 1957 as part of an exploratory program, searching for lead, zinc, copper, silver, and gold ore bodies hidden from the surface by several hundred feet of volcanic rocks. This paper describes the sinking methods and operating practices of Centennial Development Co., contracting firm for Bear Creek Mining Co., in sinking a 3-compartment vertical shaft 1,100 feet. The operation featured the Cryderman positive-action, clam-type shaft mucker. The shaft was completed in 142 days by a shaft crew of 10 men and a top force of 10 men, including supervision.

Jan 1, 1959

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill und blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By GLADYS G. HEFFNER, William H. Waggaman, Edwin A. Gee

Thallium is one of the rare and relatively neglected elements that has recently assumed conspicuous importance. This element is widely distributed in nature but occurs in such minute quantities in most rocks and minerals that its recovery at present is only commercially feasible as a byproduct of other industries. World War II, with its unprecedented demand for products having special or unusual properties, led to a study of a number of the rarer elements that previously had been given comparatively little attention for one or more of the following reasons: 1. 2. Limited knowledge of properties. Small quantitios present in available raw materials. 3. High cost of concentration and recovery. Some of those rare elements, either alone or in the form of compounds, have already proved of such value for certain military and industrial purposes that their extraction from ores and waste products, oven at high cost, is fully justified. On the othor hand, further investigation of their character- istics, discovery of more adequato sources, and improvement in methods of con- centration and recovery would greatly broaden their field of usefulness and establish new and expanded industries. The current market for some of these elements exceeds the available supply. One of the functions of the Bureau of Mines is to study the properties of such elements in greater detail, locate the most promising raw materials from which they can be derived, and work out methods of extraction that will render the recovery of such elements more economical. The purpose of a serios of information circulars on the raror elements is to present in condensed form the facts and data so far available. This information may serve as a basis in planning more complete investigations loading to a full utilization of such elements.

Mar 1, 1950