Search Documents

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By Scott Turner

The present rapid growth of coal stripping in the United States is a curious reversal of the tendency of mining to proceed from outcrop to depth. A combination of technical and economic factors bas stimulated the use of stripping methods until today many million tons of coal We being recovered by open cuts from sites that an earlier generation of engineers would have passed by as not commercially mineable or, if workable at all, only by underground methods. The total quantity of bituminous coal and lignite mined in the United States by stripping in 1928, the latest year for which detailed figures are available, was 19,789,000 short tons. Of this, 71,000 tons came from small workings not equipped with power shovels and 587,000 tons from properties in which stripping and underground work were carried on at the same mine; but as neither of these types is representative of modern stripping practice, they will be omitted in the discussion that follows. The total from strip pits proper in 1928 was 19,131,000 tons, produced by 176 pits employing 385 steam or electric shovels.3 Figures by States are given in Table 1. Detailed statistics will be found in Economics of Strip Coal Mining; a study by O. E. Kiessling, to be published by the United States Bureau of Mines.

Jan 1, 1930

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

By Lance R. Barron

The U.S. Bureau of Mines (USBM) conducted ground pressure analysis of a wide abutment-type chain pillar in a two-entry gate road of a Western U.S. coal mine with an extremely weak immediate roof. About 15 m of fragile, low-strength mudstone lies between the seam and the lowest competent roof member. Three-and two-entry gate road designs with several pillar sizes and various secondary support systems have been employed to improve tailgate-entry stability, with varying results. This report discusses gate road layout and performance and secondary support effectiveness. The results of the pillar pressure study are compared to pillar loading predicted by a widely used pillar design method and to similar studies in other mines. A stability evaluation of the most recent longwall headgate, using the USBM Analysis of Longwall Pillar Stability (ALPS) method, indicates marginal stability in first-panel mining and instability in second-panel mining. The ALPS method and the USBM Coal Mine Roof Rating system are used to evaluate tailgate-mining stability of the previous gate roads and to determine pillar and entry width and top coal thickness criteria for tailgate stability in future panels.

Jan 1, 2010

By B. J. Scheiner

The Federal Bureau of Mines investigated an electrolytic oxidation procedure for extracting lead, zinc, copper, and silver from lead-zinc concentrates. Concentrates slurried in brine were pumped through the anode compartment of electrolytic cells equipped with selective ion diaphragms. Hydrochloric and hypochlorous acids generated in the anode compartment converted the metal sulfides in the concentrates to soluble metal chlorides, sulfate ion, and elemental sulfur. Metal extractions of 92 to 100 pct were obtained from lead-zinc concentrates at an energy consumption ranging from 1.5 to 5.0 kW-hr/lb metal extracted. Sodium hydroxide was formed in the cathode compartment at a current efficiency of >99 pet. Silver and copper were extracted from refractory tetrahedrite minerals, but the process entailed a relatively high energy consumption. Sealing the top of the diaphragm cell utilized the chlorine more effectively, thereby reducing energy consumption 10 to 50 pct.

Jan 1, 1975

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research-(CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. 2/ No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43. the semiannual reports were resumed.

Jan 1, 1950

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1951 are presented in this bulletin under the following general heads: (A) General injury experience: Tables 1 to 18: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major and detailed injury agencies, and distribution of injuries by part of body and days of disability. (B) Selected injury data: Tables 19 to 43: Contain current data on various selected factors of operating and physical conditions that contributed to the occurrence of injuries at bituminous-coal, lignite, and anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy or nongassy, types of cap lamps, explosives, and combination of factors that influence mine safety. (C) Injury experience by States: Tables 44 to 50: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major causes and principal agencies, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Major disasters: Table 51: Lists the coal-mine disasters that occurred during 1951, giving location, source, and cause. A major disaster in coal mining is defined as a single accident in which or as a result of which five or more men lost their lives. (E) Historical coal-mine injury experience: Tables 52 to 86: Contain data on injuries, injury-frequency rates, employment, and production at bituminous-coal, lignite, and anthracite mines from the earliest records through 1951.

Jan 1, 1955

The Determination of Sound Exposures (DOSES) software was developed by the National Institute for Occupational Safety and Health (NIOSH) specifically for use by mine management and safety personnel. DOSES simplifies the record-keeping and analysis associated with time-motion studies and worker noise exposures, making it easier to identify and solve noise problems. The software relies on a time-motion study that profiles the worker?s daily activities. At the same time, noise measurements are collected with a dosimeter or sound level meter (SLM). Observations about the worker?s location and tasks or other activities are recorded along with times and durations so they can later be matched up with the noise data. After the completion of a time-motion study of the worker?s daily tasks and locations (possible noise sources), which measures the worker?s noise exposures during the recorded events, the information is entered into DOSES. The program then displays information about the worker?s accumulated noise dose over time.

Jan 1, 2009

By Robert E. Barieau

This report gives the principles of the method used by the Helium Research Center of the Bureau of Mines when solving nonlinear-regression problems and contains the mathematical equations necessary to accomplish the following objectives: the evaluation of the parameters in such a way that the sum of the weighted squares of the residuals of an experimental observable is a true minimum, regardless of the functional relationship between the variables and these parameters; and the evaluation of all variances and covariances of the parameters by means of the usual approximation of the law for the propagation of errors.

Jan 1, 1967

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled in tie following pages and constitute the annual report of the division. In planning activities, the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those current activities that contribute most to problem of present concern are emphasized, investigations of less immediate importance being recessed, if necessary.

Jan 1, 1940

By R. V. Lundquist

The compound 2Na2O?3CaO?5Al2O3 occurs as a minor phase in lime-soda sinters prepared for extracting aluminum from siliceous aluminum-bearing materials. About 99 percent extraction of sodium and aluminum from synthesized 2Na2O.3CaO.5Al2O3 was obtained in solutions of NaOH-Na2CO3 at leaching temperatures of 50° C and above. Extractions in water were low because insufficient NaOH was generated by hydrolysis. Extractions in NaOH solutions were limited to about 80 percent owing to the precipitation of hydrated calcium aluminates. Rapid extractions of 100 percent were obtainable in NaaC03 solutions, but the subsequent rapid precipitation of alumina trihydrate caused losses in alumina recovery.

Jan 1, 1965

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

By B. J. Moore

This publication contains analyses and related source data for 191 natural gas samples from 22 states and 1 foreign country. Of the total samples, 182 were collected during calendar year 1987. The remainder were collected earlier, but releases granting permission to publish were not received before 1987. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1988

By Chas. F. Jackson

The annual reports of the supervising engineering of the nine sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those current activities that contribute most to problems of present concern are emphasized, investigations of less immediate importance being recessed, if necessary.

Jan 1, 1940

By Jr. Reed

The only known large deposits of talc in Alabama occur near Winterboro, Talladega County. Preliminary examinations were made, and work by the Bureau of Mines was recommended. The deposits were investigated to determine the amount and grade of talc present and to search for new talc deposits in the general area. Seventy-five holes, totaling 3370.4 feet, were drilled with Government-owned core drills from August 1, 1948, to February 11, 1949, and 27 samples were taken for assay. This report presents the factual data disclosed by drilling and the results of beneficiation of the talc.

Jan 1, 1950

By C. W. JEFFERS

At its annual meeting on March 5, 1928, in Washington, D. C., the Joseph A. Holmes Safety Association gave to the Ford Collieries Co., Curtisville, Pa., a certificate of honor for "having worked 922,628 underground man-shifts from August 14, 1920, to December 31, 1926, producing 5,755,669 short tons of coal without a fatality." This remarkable record certainly deserved recognition. It developed that this company's freedom from fatalities continued until October 2, 1929, hence the full period during which no underground fatalities occurred was from August 14, 1920, to October 2, 1929, or 9 years, 1 month, and 18 days, the total tonnage being over 7,700,000. Table 1, shows the complete safety record of the Ford Collieries Co. since 1920 as given by the officials of the company. The first item in Table 1 shows a remarkable performance. This company since 1920 has mined 15 times more coal per fatal accident than the average pro- duction per fatal accident for the State of Pennsylvania in 1928 (255,257 tons). Excluding the two fatalities (one in 1922 and one in 1929) the severity rate for the same period has been 1.259 per thousand hours worked, a record of which the company may justly be proud. However, including the fatal accidents the rate is 2.407. This compares favorably with an average of 12.4 in 1928 for 66 mines in the National Safety Competition. The Ford Collieries Co. operates three mines located in the vicinity of Curtisville, Allegheny County, Pa. One of these mines, Benjamin No. 1, is idle at the present time. The officials are: A. R. Pollock, general manager, Curtisville, Pa., and C. W. Pollock, assistant general manager in charge of safety and operation.

Sep 1, 1930

By J. T. McCartney

The Bureau of Mines has developed an automated reflectance scanning microscope system, primarily for determination of volume proportions, size distribution, and mode of association of the physical (petrographic) components of coals. The process, which is potentially more rapid and objective and less tedious than a visual microscopic procedure, involves magnetic tape recording of several millions of reflectance readings on micro-meter sized areas of polished coal surface and computer analysis and interpretation of some characteristics of the coal components. The system was tested in a study of pyrite distribution in steam coals. The application was essentially successful, but defects in polished pyrite surface characteristics and problems in adequate sampling prevented completely satisfactory results. Pyrite con-tent and coal-pyrite particle association could be determined nearly as well as by visual microscopy, but size distribution data were less acceptable.

Jan 1, 1969

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By F. S. Boericke

"INTRODUCTION The mineral found in natural-chromite deposits is never pure Fe0.Cr203, but rather one in which the Fe0 and Cr203 are in part replaced by Mg0 and A1203, respectively. The purest gravity concentrates from many domestic de¬posits consist of a mineral referred to as ""picotite,"" in which this isomorphous replacement is such that the ratio of chromium to iron is low. The Bureau of Nines has investigated methods of chemically beneficiating ores that contain too much iron to be classed as ""high-grade"" chromite 3/ Early investigations 4/ demonstrated that high-iron chromite or picotite ores can be roasted with carbon to obtain selective reduction of the contained iron, and that most of this reduced iron can be removed by acid-leaching the roast products to produce residues of higher chromium-to-iron ratios. tests 5/ indicated that commercially acceptable reaction rates cannot be obtained at roasting temperatures below 1,3000 C., using solid carbon as reducing agent. By this high-temperature reduction and subse¬quent acid-leaching, however, all ores investigated, regardless of the original composition, readily yielded residues considerably better than the minimum specifications for high-grade chromite.In an effort to obtain satisfactory reduction of chromite at lower temperatures, liquid and gaseous seducing agents were tested with varying success. Of the several reducing agents used, methane appeared to be the most promising and was shown to be highly effective at temperatures between 1,000º and 1,100º C., roughly 300º below the roasting temperatures necessary in solid carbon reduction. Further experiments indicated that mixtures of methate with some diluent (hydrogen or other nonoxidizing gas) gave better reduction than did methane alone."

Feb 1, 1946