Search Documents

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By Larry L. Anderson

Enormous quantities of organic wastes are produced each year in the United States. The total amount is in excess of 2 billion tons and at least 880 million tons of this is moisture- and ash-free organic material (dry organic solids), representing a potential energy source of significant magnitude that is not being utilized. Bureau of Mines scientists have developed methods for converting these wastes to convenient energy forms. This report itemizes and evaluates for the first time in detail the quantities and sources of moisture- and ash-free organic material contained in manure, urban refuse, industrial wastes, sewage solids, and agricultural wastes in the United States. Furthermore, estimates are presented for amounts of organic wastes collected or concentrated. The potential for fuel, either oil or gas, from both the total organic wastes generated and those collected or concentrated is also estimated.

Jan 1, 1972

By C. H. Riggs

"INTRODUCTION The injection of gas into the McClosky limestone in the adjoining, Griffin and New Harmony field in Indiana and Illinois and resulting increases in oil and gas production from this zone ore described in this report.Since 1911, the use of compressed air or as to increase oil production by supplementing natural reservoir energy has been widely adopted, and has resulted in the recovery of much additional oil, which otherwise would have been left underground. In many of the newer oil fields, including Griffin and New Harmony, a part of the compressed residue gas from natural gasoline plants is returned to the reservoir as a secondary method to increase oil and gasoline production. Part of the injected gas is stored underground for future use.By presenting data on many secondary recovery operations in a series of reports 5-9/ the Bureau of Mines has sought to stimulate interest in secondary recovery as a means of increasing oil recovery and current oil production for wartime needs. Most of the elder fields in the United States produce oil from sandstone reservoirs, and probably more than 90 percent of secondary recovery operations have been developed in oil bearing sandstones. During recent years, the volume of oil obtained by primary methods from limestone reservoirs has increased steadily, but as yet little has been done to recover, by secondary means,,the large volumes of oil left in limestone reservoirs when primary methods production are no longer profitable. Because of inherent differences in the origin and nature of the pore spaces between sandstones and limestones and because of differences in permeability and fluid content, secondary recovery methods, which are successful in sandstone-reservoirs, are not always applicable to limestones. Not much he been written concerning secondary recovery operations in limestone reservoirs, and few data are available to assist operators in developing such secondary recovery projects."

Jul 1, 1945

By Wilder D. Foster

In the method used in the Health Branch of the Bureau of Mines for petro-graphic identification of the minerals in a rock, the sample is crushed, ground to a fine powder in a mortar, the powder is put on a slide, a drop of index oil and a cover slip are added, and the slide is ready for examination. The rock should be ground fine enough so that most of the particles consist of only one mineral, otherwise identification is difficult. Finally, the amounts of the minerals present in the sample are estimated to the nearest 5 or 10 percent. When quartz grains are mixed with some claylike minerals) of which by far the most common example is quartz and kaolinite in a shale, grinding in a mortar does not always separate the quartz from the kaolinite; instead, the quartz grains become coated with the kaolinite and are not visible, even after careful search. Talc acts Similarly, but muscovite and pyrophyllite do not. In evaluating the possible silicosis hazard of breathing dust from a shale, it is essential to be able to see and identify all of the quartz grains, as the other minerals present are relatively innocuous.

Jan 1, 1949

By Nan C. Jensen

Silica, the world's most abundant mineral compound, is composed of the two commonest elements - oxygen and silicon. In addition to being the life-giving constituent of the atmosphere and the major element in the waters of the earth, oxygen comprises almost half of all known terrestrial matter and occurs combined with most of the other ninety-odd elements in the solid crust of the earth; however, a large proportion of the oxygen is combined with silicon. Silicon is second only to oxygen in abundance in nature and constitutes more than one-fourth of all known terrestrial matter. The compound of oxygen and silicon, called silicon dioxide or silica, forms 59.08 percent of the earth's outer 10-mile crust. Some of the silicon dioxide exists as

Jan 1, 1942

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By J. Roger Loebenstein

Demand for arsenic exceeded supply, and major domestic and foreign producers allocated available supplies to customers for the fourth consecutive year. Major demand for arsenic was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-Effective April 1, 1981, taxes were collected from companies producing and importing 42 chemicals and petroleum products designated as hazardous, The revenue was used to begin funding of the 5-year, $1.6 billion "superfund" being established under Public Law 96-510, the Comprehensive Environmental Response, Compensation, and Liability Act, designed to help clean up spills of hazardous substances throughout the United States. As hazardous chemicals, arsenic metal and arsenic trioxide were taxed at the rate of $4.45 and $3.41 per short ton, respectively.

Jan 1, 1982

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By Jasinder S. Jaspal

In underground room-and-pillar mining methods, the sectional conveyor belts are extended or retracted periodically to maintain shuttle car tramming distance to a minimum. A conventional conveyor belt extension or retraction is a heavy, arduous job that if mecahnized, has the potential to improve productivity and safety. To reduce the burden of heavy work of this activity and mechanize it, the Bureau of Mines developed a conveyor belt service machine (CBSM) through a research contract with Tractor MBA. The CBSM is a self-contained, battery-powered, rubber-tired vehicle capable of handling, storing and transporting conveyor belting, wire rope, and associated belt structures in seams as low as 48 in. Belt extensions and retractions are accomplished by moving the tailpiece of a belt conveyor with the CBSM to the next position while dispensing or retrieving the belt, wire rope, and associated belt structures. The CBSM improves the belt extensions and retractions by making them easier and faster, and it utilizes fewer workers. The CBSM was surface tested at the Bureau's Mining Equipment Test Facility (METF) to evaluate its performance and reliability. Modifications were made to the CBSM to correct deficiencies found during surface testing.

Jan 1, 1988

By A. M. Evans

Because of an urgent national need for manganese, the deposits in the Little Florida Mountains of Lune County N. Mex., were visited by O.H. Metzger, an engineer of the Bureau of Mines, on June 12 and 13, 1940, accompanied on the second day by S. G. Lasky, a geologist of the Federal Geological Survey. After this preliminary examination, it was recommended that exploratory work be done by the Bureau of Mines on several properties in the district. An exploratory project of trenching, sampling, and core drilling was started by the Bureau of Mines in September 1940 and completed in May 1941.2/ Work was done on three properties - the Luna mine, the American group of claims, and the Manganese Valley mine. The Little Florida manganese district is situated on the eastern slope of the Little Florida Mountains about 2 miles south of U. S. Highway 80-90, 12 to 14 miles southeast of Deming, Luna County, N. Mex. The principal claims comprise the Luna Manganese, American, and Manganese Valley groups.

Jan 1, 1949

By G. Asai

The purpose of this Bureau of Mines investigation was to determine the properties of arc-melted iron-chromium alloys ranging in chromium content from 12 to 50 wt.-pct. Alloys were prepared by consumable-electrode arc melting of electrodes composed of high-purity chromium and high-purity iron. Alloys were fabricated to rod and sheet, and the following data were obtained: Electrical resistivity, hardness, tensile strength, and impact strength at room temperature; and creep-rupture life at 650° C. (1,200° F.). As the chromium content of the annealed alloys varied from 12 to 50 pct., the properties varied as follows: The electrical resistivity increased proportionally from 41 to 53 microhm-cm,; the Rockwell hardness varied from A 38 to A 58; the tensile strength ranged from 52,000 to 96,000 p.s.i.; the impact strength of V-notched charpy specimens varied from 140 to 405 ft.-lb., and the 100-hour creep rupture life at 1,200° F. varied from 5,000 to 16,000 p.s.i.

Jan 1, 1962

By J. S. Tosh

An equilibrium study of the system potassium carbonate, potassium bicarbonate, carbon dioxide, and water has been conducted with solutions of 20-, 30-, and 40-percent equivalent potassium carboaate concentrations. These equilibrium data cover the operating range of the hot carbonate scrubbing system for removing carbon dioxide from gas mixtures. Such data are necessary to establish the limits of purification and are used to design absorption and regeneration towers. Values of K in the relationship K = (KHCO3)2/(K2CO3)PCO2 were determined for higher temperatures of 70" to 140° C. and greater concentrations, I 20 to 40 percent, than employed by previous investigators. For the 20- and 30-percent concentrations, K is constant at a given temperature; thus, once K has been determined the equilibrium pressure of carbon dioxide can be calculated for any conversion. Variation of & values with changing conversion was observed with the 40-percent solutions, so that equilibrium calculated pressures are less reliable from average K values.

Jan 1, 1959

By M. Clair Smith

The Sweetwater, Castro, Trinidad, New London, and Hilltop chromite properties are situated within an area 8 miles long and 1 mile wide between San Luis Obispo city and Morro Creek, San Luis Obiso County, Calif. Development work at this group of mines was a part of a long-range project by the Bureau of Mines to develop strategic mineral reserves in the United States in accordance with the Strategic Minerals Act of 1939. The junior author of this report participated in the preliminary examinations made in 1941 of the chromite deposits that later in the same year were the subject of more intensive investigation under the immediate supervision of the senior author. The ore occurs in lenses and kidneys in masses of dunite contained in large poridetite areas. Production has boon in the form of lump ore and concentrates from disseminated ore. Work by the Bureau of Miner included surveying, mapping, trenching, sampling, and assaying. It is summarized separately in the text under the name of each mine investigated. The report gives a brief history of the district, describer the concentrating plant of the Castro Associates, and gives detailed results on sampling and assays at the various proportion.

Jan 1, 1951

By F. W. Lee

Operating engineers and mining executives are interested in the science of applied geophysics, but are looking for a simple and understandable exposition of its problems, instead of dissertations which are becoming more and more involved and increasingly difficult to comprehend. It may be well to discuss the goal, the attempted methods of reaching it and the psychological motive, if any, tack of the science. Where does the subject of applied geophysics stand from the viewpoint of (1) the physicist, (2) the mathematician, and (3) the geologist? Fundamentally, the science aims at a differentiation of subterranean geology with the object of finding useful mineral products by the study of gravitational, magnetic, seismic, electric, and other fields which may be associated with the materials naturally or which may be applied to them. The more skillfully these fields are recognized, applied, and analyzed the greater will be the possibility of interpreting results in a way that will be remunerative both economically and scientifically.

Oct 1, 1931

By David Schlain, C. B. Kenahan, F. X. McCawley

The electrodeposition of protective coatings of tungsten from a sodium and lithium borate - tungstate - tungstic oxide fused salt electrolyte was investigated . Soluble tungsten anodes were employed . Deposits were made on molybdenum , Carpenter 20 stainless steel , Inconel , and nickel . An atmosphere of argon was maintained around the electrolytic cell , and the electrolyte was stirred by rotating the cathode . Thick deposits of tungsten (up to 26 mils ) were made at a temperature of 900 ° C and cathode current densities of 0.3 to 0.4 ampere per square inch with high current efficiencies . The effects of variations in temperature , current density , electrolyte agitation , and tungstic oxide content of the electrolyte and of the presence of impurities such as moisture , air , iron , and nickel were investigated .

Jan 1, 1964

By R. S. Fowkes

The Bureau of Mines constructed a fully automated pilot plant facility to study the hydraulic transportation of solids through a lock hopper feeder system. An equation for the energy requirements to transport coarse solids hydraulically proved applicable to this system. Optimum velocities were obtained for limestone, mine refuse, and bituminous coal. The experimental data, calculations, and graphs show the effect of velocity, specific gravity, and solids concentration on head loss and power requirements. Other data were obtained and evaluated to determine the effect of particle size on head loss. Results also are given for (a) tests using friction reducing polymers; (b) tests using seven test sections of steel alloy pipe to determine their wear characteristics; (c) tests to determine spatial segregation of moving particles; and (d) tests to determine the effect of shape, size, and specific gravity on particle velocity in a horizontal pipeline. The lock hopper feeder system was found practical for continuous hydraulic transportation of the material types and size ranges tested.

Jan 1, 1969

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 318 petroleum refineries in the United States with a total daily crude throughput capacity of 8,632,390 barrels as of January 1, 1956. Compared with the previous year the total number of refineries declined 8 while the crude throughput capacity increased 211,760 barrels daily. Three refinery districts accounted for 90 percent of the crude-oil capacity increase, the California district 34 percent; the Texas Gulf Coast district, 31 percent; and the Indiana-Illinois-Kentucky district, 25 percent. Decreases in capacity during the year were reported for the East Coast, Appalachian #1, and the Arkansas-Louisiana Inland districts. The capacity of the average refinery to process crude oil increased during 1955 from 25.830 barrels daily to 27,145.

Jan 1, 1956

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections (A) General injury experience: Tables 1-3: Current data on number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4-5: Current data on number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment, data. (C) Injury experience by States: Tables 6-20: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 21-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and nondimension-stone quarries and at underground quarries. (E) Historical injury experience: Table 31: Injury and employment data on the quarrying industry for 1911 through 1957. Statistical data on injuries and related employment in the quarrying industries have been collected annually from the operating companies since 1911. Reporting to the Bureau of Mines is voluntary; there is no Federal law compelling operators of quarries and related plants to supply such data. Data presented herein may not be complete for the entire industry. They are however, believed to be representative of the hazards common to all quarry and related workers. Moreover, the figures are comparable as between States-a significant fact in view of the lack of uniformity among the States with regard to the classes of injuries covered by State reports and other factors that tend to make it impracticable or impossible when using State records to

Jan 1, 1960

By Kenneth P. V. Lei

The Bureau of Mines investigated a silver-catalyzed oxidative procedure for leaching an arsenical copper sulfide concentrate containing 10 pct As and 32 pct Cu_ Currently, there are no environmentally safe means to treat arsenical copper concentrates in the United States. Leaching was conducted in a 2-L autoclave reactor. The effects of catalyst concentration, O2 pressure, temperature, and H2S04, Cu, As, and Fe concentrations in the leaching solution on extractions of metals from the concentrate were determined. The best leaching conditions for extracting 95 pet eu and As and less than 21 pct Fe were 260 g/L concentrate, 0.007 mol/L (1.0 g/L) AgCI, 3.0 mol/L (294 gIL) H2S04, 1000 C, 60 psig 02, and 6 h. Copper as CuS04-5H20 was recovered by crystallization from the pregnant solution. Arsenic, as AS203, was recovered from the copper mother liquor by solvent extraction, with tributyl phosphate, S02 reduction of As5+ to As3+ in the strip solution, and crystallization of the As3+. The silver catalyst was recovered by contacting the leached residue with a brine solution. A conceptual scheme is proposed for treating arsenical copper sulfide concentrates.

Jan 1, 1987