Search Documents

By J. F. Barkley

Under the procedure of the American Standards Association, with the American Society for Testing Materials as sponsor, the Sectional Committee on Classification of Coals has arrived at the classification of coals by rank as shown in Table 14/. The standard explains the term "agglomerating" used for classification under physical properties, as follows: Agglomerating Index. - Coals which in the volatile-matter determination produce either an agglomerate button that will support a 500-g weight without pulverizing, or a button showing swelling or cell structure, shall be considered agglomerating from the standpoint of classification.***. Pending the adoption of a method by the American Society for Testing Materials, the coke-button grading test5,/ afforded by the examination of the residue in the platinum crucible incident to the volatile matter determination, shall be used.

Jan 1, 1937

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By Wilton Johnson

Native asphalt was produced by three companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm, R. L. White Co., Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Colorado and Utah, was mined by two firms, American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), and Ziegler Chemical and Mineral Corp. Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) closed its mining operation during the year.

Jan 1, 1988

By Steven R. Munts

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the South Providence Wilderness Study Area (WSA) in 1982. No mines are currently operating in the WSA, however, the Golden Gift Mine in the southeastern part of the WSA produced $6,800 1/ worth of gold and silver and five mines adjacent to the east boundary of the WSA had a total production of about $3,500,000 1/ in gold, silver, lead, and copper. There is no recorded placer gold production. Over 350 lode and placer mining claims are in and immediately adjacent to the WSA. Of these, 74 were actively held (1982) and at least one area, which is partly within the northeast portion of the WSA, was being actively explored by private industry in 1982. Adjacent to the southeastern border of the WSA the Big Horn Mine contains an estimated 200,000 tons of indicated and inferred marginal reserves averaging 0.25 oz/ton gold; and the Hidden Hill Mine has 550 tons of subeconomic resources averaging 0.60 oz/ton gold. An additional 11,000 tons of marginally economic gold-bearing dump reserves average 0.17 oz/ton gold at the Bighorn, Hidden Hill, and the Buena Vista Mines and the Midas Touch Prospect. Sample analyses indicate eight mines and prospects in, and five adjacent to the WSA may have additional gold-silver-lead-copper vein-type resources. Five of these prospect areas may have a disseminated gold resource and one may have gold resources in a skarn. One prospect may have a porphyry-type copper-molybdenum resource. Although gold placer claims were filed sporadically throughout the WSA, none appears to have placer gold resources. Likelihood for mining is greatest at the Big Horn Mine; if a mill is built there, it could process Big Horn Mine ore, ore from the Hidden Hill Mine, and gold-bearing dumps at the Big Horn, Hidden Hill, and Buena Vista Mines and the Midas Touch Prospect. All of these resources are adjacent to the WSA; however, their development would increase likelihood for development of resources in the WSA. Two major fault zones (the Hidden Hill, and the Big Horn) appear to have controlled the mineralization at many of the prospects and mines. All of the prospects or mines with vein-type occurrences and resources are on or adjacent to one of these fault zones. Veins throughout the eastern half of the WSA contain various amounts of gold, silver, and copper; only veins near the Big Horn Mine and in the northeastern corner of the WSA contain lead. Some veins are as thick as 6 ft, are traceable intermittently for over 2 mi along strike, are sporadically mineralized, are encased in prophylitic, argillic, and phyllic altered host rock, contain pyrite, chalcopyrite, galena, specularite, barite, or fluorite, and display multiple stages of quartz veining and (or) brecciation. Sample analyses at five prospects (map nos. 3, 18, 23, 24, and 31) indicate they may have disseminated gold resources. To date no oil or gas has been discovered within the WSA. However, some oil and gas leases are currently (August 1982) held within this study area.

Jan 1, 1984

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By Elizabeth A. Johnson

Minor-element behavior and interaction in the copper matte-iron silicate slag system have been studied by the Bureau of Mines. In the present work, the possibility of interactions among the minor elements As, Sb, Bi, Se, and Te was investigated. Equilibrations of matte, slag, and one of each of the five minor elements were performed at 1,250° C under typical matte smelting atmospheres of CO, CO2, and S02 for mattes containing 40, 50, and 60 pct Cu. Results are compared with those of a previous Bureau of Mines study in which all five minor elements were present simultaneously.

Jan 1, 1984

By J. B. Janus

This report continues a series of analyses of coal samples made by the Bureau of Mines in connection with the yearly purchase of several million tons of coal for various Government agencies. Listed are the analytical data on the composition and quality of tipple and de livered samples of coal collected during fiscal year 1974.

Jan 1, 1975

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By Reinhardt Thiessen

This paper presents only the highlights of previous research on the paleobotany of coal. The accumulated material has become so vast that a comprehensive review of all findings relating to paleobotany would be far too long. The fact that coal is derived from plants is now so well-known that no further comment is required, but knowledge of the mode of transformation of plant substances into coal is not so general. The plant matter goes first through processes of semirottins-, maceration, and elimination of certain material to form peat, which is then further transformed into coal. The first stage has been termed the "biochemical process," because the more important changes take place under the influence of micro-organisms. Near the end of the biochemical action an unconsolidated peat is formed. The second or "dynamochemical process," caused by the addition of superincumbent rock strata such as sandstones and shales and application of additional pressure and possibly heat through mountain-building forces, results in the formation of higher-rank coals ranging from brown coal to anthracite. These stages in trans-formation of plant material to coal have been described in previous reports.4 The main object of this paper is to bring to the notice of paleobotanists the fact that coal contains an enormous amount of material in a remarkably good state of preservation. Although some of the coal-forming matter has lost its identity, much of the original structure is retained. A large proportion of the coal, therefore, particularly of common bright coals, comprises constituents or components that invariably have retained some of the original plant structure, and many of these structures may be assigned to certain plants. The identity of these plants and of the remains forms the subject of this paper.

Jan 1, 1941

By Jack E. Fraley

Because of their noncombustibility, silicate and magnesium oxycements are desirable for sealing shale in underground coal mines. In this Bureau of Mines investigation, cement samples were cured and tested (nonstandard tests) for submersion to note resistance to dissolution (breaking into parts), which is an important property for a coating. Nonappreciable dissolution during 1 week of submersion was set for passing the test. Over half of the coatings passed the test.

Jan 1, 1977

By F. E. Block, Robert R. Brown, A. W. Henderson

The chlorination of Cr₂ 03 (chromic oxide ) in the presence of carbon with CC14 (carbon tetrachloride ) and COCl2 (phosgene ) chlorinating agents was investigated by employing the radioactive tracer carbon By tagging carbon mixed with Cr₂ 0з , the chlorination reaction was evaluated in terms of the competitive reaction of the elemental carbon and the carbon contained by the chlorinating agent . A unique gas - analysis train was used to separate the chlorination product gases ; CO , CO₂ , and COC12 . The C¹ activity of the gases was determined and used to calculate the reactivity of each source of carbon . Reactivities were determined for the temperature range from 600 ° to 900 ° C. The results of the investigation show that each source of carbon reacts significantly with the Cr2 03 and that the reactivity of each form of carbon depends on the reaction temperature , and each form is independent of the other . Radioisotope and gas - analysis techniques are discussed and a description of the experimental apparatus is given .

Jan 1, 1964

By Khamis Y. Haramy

This U.S. Bureau of Mines report describes the use of Bureau-developed flat and cylindrical hydraulic borehole pressure cells. A brief description of the fabrication, installation, and pressurizing equipment is given and pressurizing procedures are discussed. Theories available on evaluation of data from the flat and cylindrical pressure cells and examples of data analysis and stress evaluation are also presented.

Jan 1, 1991

By S. A. Matthes

This Bureau of Mines report describes a system for the dissolution of metal and mineral samples using a microwave heat source. Samples and an acid mixture are placed in sealed polycarbonate vessels. The vessel contents are heated using microwaves, digested for 2 min, and quickly cooled. After the solution is brought to a final volume, the vessel contents are heated an additional 2 min in the microwave oven. Using this method, a slag, a feldspar, and a Ni-Cu alloy were dissolved and analyzed by atomic absorption spectroscopy. Values obtained for Na, K, Cu, Ni, Si, Mg, Mn, Ca, Al, and Fe agreed with certified values and had an average relative standard deviation of 1 pct. This system results in a significant savings in time and expense over traditional methods of sample dissolution, and is ideal for preparing solutions for analysis by atomic absorption, plasma optical emission, or X-ray spectroscopy.

Jan 1, 1983

By W. W. Adams

"The third annual safety contest for plants producing sand and gravel, which was conducted in 1911 by the United States Bureau of Mines in cooperation with the National Sand and Gravel Association, registered further progress in safety as compared with the two previous annual contests. Both the accident-frequency rate and the accident-severity rate were reduced.The period covered was the calendar year 1931; sixty plants participated, and 17 States were represented by the participating companies.The contest covered accidents and man-hours worked by all men at the participating plant who were employed by the same company; and it included work up to the point of delivery of the material directly to the consumer or to an independent agency of transportation--in other words, to the point of relinquishment of control of the material by the producer.The purpose of the yearly contests for producers of sand and gravel is to aid in the promotion of safety among the employees and in the reduction of accident costs to the companies. The contests develop friendly rivalry among the various plants and among the employees of individual plant in a concerted effort to prevent accidents.Two safety trophies are awarded annually, both of which are provided by Rock Products magazine. One of the trophies is for the host safety record among plants that were in operation the contest year 100,000 or more man-hours; the other trophy is for the best among plants that were in operation lees than 100,000 man-hours. Awards and the relative standing of the various plants are based upon statistical compilation by the Bureau of Mines of accident reports and employment reports furnished by the enrolled companies. are summarized at the close of each year, and the summaries are submitted to each company concerned for certification as to the accuracy of the summary and the completeness of the company's reports from which the summary was prepared. When the summery is returned signed by an official of the company, the records are considered to be a trustworthy basis for determining the relative standing of the various plants. The position of each plant is determined by its accident-severity rate; that is, the number of days of disability resulting from accidents for each 1,000 men-hours of work done by all employees at the plant."

Aug 1, 1932

By Ellis S. Hertzog

The data published in this report cover only one phase of a special study of the physical and chemical properties of Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, end ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This paper makes available for the first tine fairly comprehensive information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors have included a complete description of it in this report.

Jan 1, 1938

By Kenneth E. Hjelmstad

The U.S. Bureau of Mines (USBM) has developed an electromagnetic (EM) fire warning alarm sys-tem for underground mines. The system generates a magnetic field for through-the-earth signal trans-mission to microreceivers carried by individual miners. EM fields can induce electric currents in metallic conductors; if an EM transmitting antenna and an electric blasting cap array are too close, the field could induce a current in the blasting array and cause an unintentional initiation of the electric detonators. The USBM conducted tests that define the safe and unsafe regions for using electric detonators near the transmitting antenna of the warning alarm system. The minimum safe distance between a transmitting antenna and a blasting array is the distance where the induced electrical current in the blasting array is 50 mA, which is the safe current level specified in Federal mine safety regulations. Tests indicate that at transmitting power levels of 100-and 1,000-W, separation distances of 9 and 21 m, respectively, were required. These distances are small compared with the dimensions of a mine. Thus, the tests indicate that, with proper placement of the transmitting antenna, the warning system can be used safely in the proximity of blasting arrays.

Jan 1, 2010

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended' as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945