Search Documents

By F. G. Schwartz

This circular presents the results of a survey of research on jet fuel thermal stability jointly sponsored by the National Petroleum Refiners Association (NPRA), Tulsa, Okla., and the Bureau of Mines. The development of supersonic planes has led to many problems that did not exist in the operation of subsonic aircraft. One of the most important of these is rapid deterioration of the fuel at the high temperatures to which it is subjected. At higher speeds, aerodynamic heating of the airframe imposes severe thermal problems, and conventional techniques of rejecting the heat to the atmosphere become impractical. The fuel is the only material present in sufficient bulk to be used as a heat sink. Thus, the fuel is subjected to aerodynamic heating and also is used to dissipate heat from lubricating oil, hydraulic fluid, electronic equipment, wheel wells, and cabin air. Consequently, the fuels may have to withstand both moderate temperatures for sustained periods in the fuel tanks and higher temperatures for brief periods during transfer from the tanks to the combustion chamber. Because of high temperatures, insoluble residue or gum may form in the fuel and contribute to heat exchanger fouling and to clogging of the fuel manifolds, nozzles, control systems, and other components of the fuel system.

Jan 1, 1962

By O. Llewellyn Jack

From September 1978 to December 1983, ESD Corporation (formerly a Division of FMC Corporation) undertook the development and testing of a bidirectional auger under contract with the U.S. Department of Energy. Underground testing began in August 1981 at Peabody Coal Company's Marissa Mine near Marissa, Illinois. The auger was developed to increase mine production and coal recovery without increasing land subsidence. It bored 4-foot-diameter by 10-foot-deep holes into pillars on 7-foot centers (each hole recovering 5 tons). All operating during this test was performed by maintenance personnel with the goal of finding ways to increase the machine potential. The maximum excavation rate achieved was 1.4 tons per minute. It was concluded that the concept of drilling short holes to extract coal from underground pillars without surface subsidence was practicable with a wheel mounted auger, but that more power was desirable for this mine, and that the hydraulically driven augering system that provided experimental versatility was not sufficiently reliable for production use.

Jan 1, 1983

Auger operations produced 14 million tons of coal in 1974, or approximately 5% of all surface mined coal. It was the most efficient of all coal mining methods, producing 40.0 tons per man-day. Exhibit 1.1 gives a breakdown of productivity of all coal mining methods. Exhibit 161 PRODUCTIVITY OF COAL MINING METHODS (Short tons per man-day) [Method - 1971 1972 1973 1974 Conventional 11.00 10.00 9.75 9.30 Continuous 13.00 12.50 12.25 11.90 Strip Mines 35.69 35.95 36.00 36.00 Auger Mines 39.00 43.00 45.33 40.00 ] Unlike other surface mining methods, augering produces clean coal, largely uncontaminated by foreign materials, other than those existing in the coal seam itself. However, compared to other methods, the coal recovery rate is relatively low. For example, a triple-headed auger in a 35-inch seam would recover approximately 50% of the coal in the seam as compared to a 90 to 95% recovery rate for strip mining and a 55 to 65% recovery rate for deep-mining. The low auger recovery rate is due to the circular cuts and pillars left in the seam.

Jan 1, 1975

By R. F. Zaffarano

Data presented on the physical characteristics of the reservoir oil, Aneth field, represent the initial phase of a study of Paradox basin reservoir oils being made by petroleum engineers of the Federal Bureau of Mines, Petroleum Research Center, Laramie, Wyo. The purpose of the study is to determine the original reservoir-oil characteristics in several important new discoveries in the Paradox Basin and to investigate correlations between the properties of these reservoir oils and structural or areal position within the basin, If migration is limited and oil accumulates near its source, then it seems probable that few differences should be found in the composition and characteristics of reservoir oils occurring in given age rocks and within the confines of a geological basin. Within these limits, conditions that effected the formation of oil and its transfer from parent to storage rocks probably were rather uniform in an area the size of most of our geological basins. However, if oils should migrate considerable distances, it seems logical to expect that the relative quantities of gas and liquid components may differ in traps occurring along the direction of migration, corresponding with the theory of differential entrapment (5).4/

Jan 1, 1959

By G. B. Sonneman

This final report summarizes the work done by The Bendix Corporation, Environmental Science Division, under contract to the Bureau of Mines to design, develop and test two improved systems for remote sampling the air at the working face of a coal mine in conjunction with approved portable methane detectors and machine-mounted methane monitors respectively. The work was started in May 1973 with preliminary design studies and was completed in May 1975. Five portable and two machine-mounted sampling systems were delivered. Contract "add-on" requirements for (1) modification of the machine-mounted system to accommodate a flame safety lamp and (2) a study of sensor response time improvement for the machine-mounted system were also completed.

Jan 1, 1975

By M. C. Malamphy

The report of work accomplished on the United States Bureau of Mines' bauxite project in Pulaski and Saline Counties, Ark., is presented in this volume and in a series of Reports of Investigations immediately following this volume. This first volume covers the project as a whole, whereas the subsequent volumes contain maps of local areas and deposits developed, together with logs of the drill holes and descriptions of the separate deposits. The Arkansas bauxite project was initiated in December 1941 and continued for 4 years. The first 5 months were spent in studying the problems presented and in geophysical exploration, Core drilling began in May 1942 and ended in May 1945. The project was one of the larger and more important of those undertaken by the Bureau of Mines for the purpose of developing domestic sources of supply of critical and strategic minerals necessary for National defense and for the successful waging of modern mechanized warfare. Some of the results of the Bureau's bauxite exploratory work have been made available to the public through the medium of press releases, transactions of technical societies, and government publications. More information has been supplied to government agencies upon request and to land owners and mine operators of the deposits concerned in the form of maps showing locations of all holes drilled on the property and logs with chemical analyses of' all cores recovered. In October 1946, the factual data were made avail-able to .the public in manuscript form in an-"open file" at the office of the State geologist, R. B. Foxhall, Little Rock, Ark., and at the office of the. Bureau of Mines in Washington. For the purpose of providing a background for the presentation of the factual data obtained, the history of bauxite is reviewed briefly. Information relative to past production and reserves of bauxite in Arkansas also is given. A resume of the development of the industry in Arkansas, the exploration and mining methods employed, the various uses to which the bauxite is put, and a brief outline of the geology of bauxite in Arkansas complete the -background.

Jan 1, 1948

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975

By Koehler Stout

Previous work done by the authors of this report indicates that hydraulically-placed backfill can be strengthened several fold by various placement methods. Sunshine mill tailings were tested by these placement methods and strength increases up to thirty times were achieved over the ordinary placement methods. A computer simulation study of the test stope in the Sunshine Mine showed that a high-modulus fill absorbs up to 27% of normal stresses versus 7% for "normal" fill while reducing maximum convergence 28% versus 8% for "normal" fill. Although high-modulus fill was not placed in the test stope during this contract, various instrumentation was purchased, designed and built to record necessary data in the stope. Stress gauges were placed in the pillars and recorded data corresponded quite closely with theoretical projections.

Jan 1, 1983

By Arno C. Fieldner

From July 1, 1949, to July 1, 1950, the Bureau of Mines conducted the research and technologic work on coal and coal products that is summarized in this report. The research, described in this fifteenth of a series of resumes, is presented in more detail in publications (see footnote references) that appeared during the fiscal year, though in some cases research data are given that have not been published elsewhere. Results of research in the experimental coal mine, on explosives, and on gas and dust explosions will be found in Bureau of Mines Report of Investigations 4228, Annual Report of Research and Technologic Work on Explosives, Explosions, and Flames, Fiscal Year 1950. An over-all view of our coal, oil, end natural-gas reserves was presented, and the future possibilities for the, production of synthetic liquid fuels from coal were delineated.3/

Jan 1, 1951

By G. R. FITT, S. R. B. Cooke, C. W. Davis, V. H. Gottschalk, C. G. Maier, C. E. Wood, R. S. Dean, S. B. THOMAS, John Gross, E. P. Barrett, T. L. Joseph

Lack of funds has prevented publication of much of the metallurgical work of the Bureau of Mines during the past 2 years . The present progress report covers studies in the direct production of iron and steel . The experimental work was carried out in cooperation with the universities of California , Minnesota , and Missouri . Complete reports will be published when funds are available .

May 1, 1934

By Oliver Bowles

The manufacture of lime is one of the oldest industries. Plants are distributed widely and furnish an essential raw material for numerous industries. The use of lime by the building trades, in agriculture, and in hundreds of manufacturing and chemical processes has created demands for a large production and has necessitated exhaustive research on methods of manufacture and uses. The bibliography of lime is an extensive one, but for the most part each publication has dealt with only certain operations. The purpose of this paper is to present a general picture of the industry as a whole. The abundant literature has been abstracted and quoted freely, and the National Lime Association has rendered valuable assistance in furnishing data for certain sections. Publications containing more detailed information on the various branches of the industry are referred to in the footnotes and in the bibliography.

Jan 1, 1936

By Oliver Bowles

Lime is of tremendous importance to modern industries. In agriculture it is regarded as essential to the continued fertility of many important regions; in building it is indispensable, and in the many ramifications of the chemical industries it is so necessary and so widely employed that it has been designated "the king of all the bases." Figure 1 shows a general view of a modern lime plant producing more than 500 tons of lime daily. In 1924 the production of lime was reported from nearly every State in the Union and amounted to more than 4,000,000 tons, valued at, nearly $40,000,000. For a production of that magnitude between 8,000,000 and 9,000,000 tons of limestone are required. The many problems involved in winning this great quantity of raw material from the natural rock and preparing it for the kilns have in the past received little attention from any governmental agency. Therefore, in compliance with a request from representatives of the National Lime Association in 1922, the Bureau of Mines began a study of problems in limestone quarrying in an effort to advance more economical methods of operation and the utilization of waste material. Field studies were made at many quarries, and the information thus compiled, besides data already at hand from work in other branches of the stone industries, were disseminated to operators in the form of mimeographed Reports of Investigations, eight of which were issued at intervals during 1922, 1923, and 1924. A questionnaire was appended to each report, and quarry operators were invited to contribute additional information obtained as a result of their actual experience and observation. Operators of lime plants have been cordial in their responses and have supplied the bureau with much valuable information. From the data thus obtained, supplemented by later field studies, the revised reports have been combined to form the major part of this bulletin, which is believed fairly to represent present knowledge on the subject of quarrying limestone for lime manufacture.

Jan 1, 1927

By Bertha R. Klahold

"In response to numerous inquiries regarding tests and analyses of minerals and related inorganic materials; Bureau of Mines Information Circular 6999, ""Laboratories That Make Fire Assays, Analyses, and Tests on Ores, Minerals, Metals and Other Inorganic Substances,"" by C. W. Davis and M. W. von Bernewitz, was published .in 1938 and revised in 1939 (I. C. 6999R). In this paper on analytical and testing laboratories, the original text has been rewritten and expanded, and a table has been added, in which are listed laboratories prepared to offer a number of special testing services in addition to ordinary assays and chemical analyses. The arrangement of laboratories on, a geographical basis has been maintained.This circular is compiled as a public service, and none of the laboratories listed herein is recommended over any other,These lists were compiled from questionnaires sent to organizations whose work is connected with mineral and metallurgical testing. The response in general was very satisfactory, and the author takes this opportunity to express her appreciation to the officers of the listed laboratories for their cooperation.Acknowledgment is also made of the valuable assistance of the members of the technical staff particularly Morris Slaving/ of the Eastern Experiment Station of the Bureau of Mines at College Park, Md., in the preparation of the questionnaire and technical descriptions.Many mineral samples are sent to government agencies in the National Capital with the request that they be assayed or chemically analyzed. It should be emphasized that there is no place in Washington D. C. where assays and quantitative analyses are made for the public b the Federal Government.Virtually all of the States maintain a bureau of mines, a geological survey, or some similar organization, frequently at the State University, where minerals found by residents of the State will be identified free of charge. Usually, a charge is made for assays. Specific tests, as on clays, are made by some of these offices.The Federal Bureau of Mines, although it attempts to avoid duplication of services rendered by State Bureaus, is always glad to give advice as to prospective markets. It does not compete with private assayers and chemists, but with respect to samples sent to its field laboratories, it does offer to identify them as far as this can be done by inspection and simple optical and chemical tests. This examination is usually sufficient to indicate whether the material has commercial value, or at least if the expense of an assay would be warranted. Except in connection with its own technical investigations, no assays or other special tests are made by the Bureau of Mines.The Federal Geological Survey and the National Museum also make simple tests of specimens as a public service. Neither of these bureaus nor the Bureau of Mines, however, can afford to render such services on long suites of specimens submitted by mineral dealers, well drillers, or others, when such work can be done regularly by commercial concerns."

Oct 1, 1949

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as derived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems.

Jan 1, 1974

1. Domestic Production and Use: In 1982, 13 companies operated 30 primary aluminum reduction plants, with 3 firms accounting for 55% of production. Washington, Oregon, and Montana accounted for 34% of the production; Texas, Louisiana, Missouri, and Arkansas 18%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central and eastern States 34%. Based on published producer prices, output of primary metal in 1982 was valued at over $5.5 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 39% of domestic consumption in 1982, transportation 20%, building 14%, electrical 8%, consumer durables 8%, and other uses 11%.

Jan 1, 1983

Approximately half of all the fuel energy used in the United states is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation's reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

The first metal-mine accident-prevention course was prepared and published in 1942--45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' Circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By R. E. Heithecker

The Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalkrock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I.

Jan 1, 1934

By R. R. Sayers

That the maintenance of proper air conditions is a most important factor in the control of occupational hazards is shown by the large amount of material presented each year through the technical journal's on the effects on workers of injurious dusts, gases, and variations in temperature and humidity.. SUMMARY OF RECENT LITERATURE ON EFFECTS ON WORKERS OF EXPOSURE TO DUSTS The subject of the control of dust and dust diseases continues to be a matter of serious concern in most of the industrial countries of the world, as indicated by the following summary of reports published in a number of foreign countries as well as in the United States. Australia. The Workmen's Compensation Act of 1920 for New South Wales3 provided for the promulgation of schemes for the compensation of workers dis- abled by silica or other dust. In 1924 the prevalence of silicosis and tuberculosis among Sydney stonemasons, quarrymen, sewer miners and rockchoppers was investigated by a Technical Committee of Inquiry, appointed upon the recommendation of the New South Wales Board of Trade. The findings of this committee were published by the Government in 1925. No scheme was promulgated by the Government and in 1926 the Act was amended limiting its scope to workmen disabled by disease caused by silica-dust. This was promulgated and gazetted on September 16, 1927, and applies to men working in sandstone as stonemasons, quarrymen, rockchoppers, and sewer miners in the County of Cumberland.

Feb 1, 1931