Search Documents

By Van E. Shaw

Three comparatively simple, efficient, and rapid extraction methods for the dissolution of yttrium and rare-earth elements from a euxenite carbonate residue have been developed, using dilute sulfuric acid as the solvent. Extraction processes have resulted in yields of 98+ percent of the total rare-earth elements and yttrium contained in the residue and have given preliminary separation between the cerium-group and the yttrium-group rare-earth elements. Extraction procedures presented are: Procedure 1. -The recovery of total rare-earth elements and yttrium by a cold dilute sulfuric acid leach at a pH of 2.5. Procedure 2. -The recovery of yttrium and yttrium-group rare-earth elements by leaching with dilute sulfuric acid at 125° F. and a pH of 3.0, with subsequent recovery of the cerium-group rare-earth elements by a cold dilute sulfuric acid leach of the residue at a pH of 2.5. Procedure 3. -The recovery of the total rare-earth elements and yttrium by fractional leaching as in procedure 1, followed by boiling the sulfate solution, which precipitates the cerium-group rare-earth elements and leaves the yttrium-group rare-earth elements in solution.

Jan 1, 1959

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Haiti has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930

By Glenn C. Reed

The Sheep Creek iron deposits, Meagher County, Mont., were investigated by the Bureau of Mines in 1943 and 1944. Work undertaken included exploratory trenching, churn drilling, petrographic studies, and detailed beneficiation tests. It was determined that the Sheep Creek ores occur both as fissure filling and bedding replacements in thin-bedded shale and arenaceous limestones of the Algonkian Belt series. At least five stratigraphic horizons were found to be mineralized. Metallurgical studies indicate that the ores are not amenable to beneficiation by present-day low-cost methods. Details of geology, sampling, and beneficiation tests are presented in this report.

Jan 1, 1949

In 2001, 14,623 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). This was an increase of 210 mining operations compared to 2000. Almost half (49%) were sand and gravel mines, followed by stone (29%), coal (15%), nonmetal mines (5%), and metal mines (2%).

May 1, 2003

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By H. A. Doerner

For the past three or four years attention has been attracted to the deposits of lead vanadate in the Goodsprings , Nevada , district . Some ore running as high as 9 per cent 205 has been produced , but most of it runs from 0.5 to 3 per cent . Only a little ore , and that of the richer sort , has been shipped , since the low- grade ore will not stend the cost of shipment and no concentration mill has been available . Preliminary experiments indicate that chemical treatment of the low- grade ore without concentration is not feasible . Its treatment therefore involves two distinct problems ; first , mechanical concentration ; and second , a smelting or chemical treatment to obtain the lead and vanadium in marketable form . Upon this basis the work has been conducted . The writer wishes to acknowledge the excellent work done by J. T. Norton and Virgil Miller on table concentration and by J. E. Conley , who suggested and did preliminary work on the direct smelting method . Many helpful suggestions were received from Dr. S. C. Lind and John Gross of the Bureau of Mines . The ores were furnished by Mr. Frank Williams and Mr. James Ewing .

Jan 1, 1923

By Bruce D. Hanson

The Bureau of Mines conducted a series of ignition tests with two types of conical bits (plumb bob and pencil) used on continuous mining machines, to determine their ignition potential at various bit speeds, cut depths, and wear conditions. The tests were conducted using single bits mounted on a 34-in-diam drum in a Bureau ignition test facility. The bits impacted blocks of Berea sandstone in a 6.5 pet methane atmosphere at various bit speeds and cut depths. In a new condition, the plumb bob bits were considerably more incendive than the pencil bits, causing ignitions in 32 of 35 tests at 60 rpm, compared with ignitiolls in 2 of 22 tests for the pencil bits. The results from new bit testing also show that reduction of bit tip velocity to 180 fpm does not eliminate ignition potential. When subjected to progressive wear, bits of both types were more incendive when they were locked in place, unable to rotate, than when they were free to rotate.

Jan 1, 1983

By J. P. Powell

Records show that systematic water flooding was begun as early as 1935 in Greenwood County and in 1937 in Butler County. Water flooding on some earlier projects in Greenwood County were described in a Bureau of Mines Report of Investigation.2/ This report presents a discussion of 4 projects -2 in Butler County, 1 in Greenwood County, and 1 in Butler and Greenwood Counties. The location of these projects is shown in figure 1. The projects have been in operation 6 to 12 years and have recovered about 6.6 million barrels of additional oil from the injection of 84.7 million barrels of water. Three of the projects take advantage of the elevation of the nearby hilly terrain, and water from the treating ponds flows by gravity through the filters into the clear-water tanks. By utilizing gravity flow, fewer pumps and less electrical energy is required, resulting in more economical operation.

Jan 1, 1956

By F. A. Rutledge

The W. E. Dunkle mine, sometimes called the Costello Creek coal mine, is 8 miles N. 20° W. of Colorado Station on the Alaska Railroad. The presence of coal in this area has been known since the district was extensively prospected for gold between 1911 and 1915. At that time, coal from this deposit was used by miners for blacksmithing. The increased demand for coal resulting from government defense projects in Alaska led to exploitation of this deposit in 1941. The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska was responsible for establishment by the Army of the Coal Procurement Section of its Alaska Department. It proposed to investigate the deposits and to expedite production from the Alaskan coal fields. The Bureau of Mines closely cooperated in this program. The quality of the Dunkle coal and the favorable location of the deposit caused it to be one of the properties chosen for investigation under a joint Army-Bureau of Mines-Geological Survey program.

Jan 1, 1948

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant's group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

By Ren G. Dong, Thomas W. McDowell, John Z. Wu, Chris Warren, Dan E. Welcome, Chun L. Dong

Hand forces are important factors for risk assessment of hand-arm vibration syndrome (HAVS).1 Grip force is one of the most important force components in the operation of powered hand tools. A considerable number of studies on grip force have been reported. It is well known that the grip force applied on a cylindrical handle is not uniformly distributed on each axis across the center of the handle cross-section.2 Therefore, maximum and minimum orientations of grip force exist around the handle. Such orientations have not been clearly identified. In a recently proposed international standard (ISO/CD 15230, 2005),3 it is stated that “the direction of the main gripping force is generally parallel to the z-axis defined in ISO 8727.” 4 This assertion is questionable, and further examinations are required. The objective of this study was to establish a fundamental theory on the distribution of the grip force around cylindrical handles. Methods As shown in Fig. 1, the grip force is defined as a vector composed of normal and shear components (FN & FT) in this study. Fig. 2 shows the hand coordinate system defined in this study, together with the ISO systems.1,4 Based on this novel grip force definition, we derived four fundamental properties and a theorem. More significantly, we formulated a novel hypothesis: similar to Mohr’s circle of stress, the normal and shear components can be represented approximately using an ellipse on the plane of the two force coordinates, as shown in Fig. 3. The maximum and minimum grip normal forces are termed as the first principal grip force (F1) and the second principal grip normal force (F2), respectively. Their corresponding orientations are termed as the first principal grip angle (a1) and the second principal grip angle (a2). A series of experiments were conducted to test this hypothesis. Twelve

Jan 6, 2006

By Lorenz E. Sieffert, Lawrence B. Berger, H. H. Sehrenk, Ralph W. Stewar, James A. Gale

"INTRODUCTION The purpose of the investigation discussed in this article was to evaluate the toxic hazard from gases produced when thermosetting plastic materials used for electrical insulating purposes are burned or thermally decomposed in enclosed spaces. For brevity the term ""toxicity"" is used throughout the article to refer to the nature of gases produced under these conditions. A need for immediate study of the problem was created as a re¬sult of the battle damage reports received from various United States Fleet units. These indicated that the fumes emitted when these materials were burned or thermally decomposed had, in several instances, resulted in toxic atmospheres. In attempting to develop a suitable test method for evaluating toxicity, it was recognized that no single test procedure could be expected to duplicate the variety of conditions that might exist in an actual fire aboard ship. In view of the immediate need, however, it was felt that considerable information could be obtained, at least to classify comparatively the several types of materials as to the toxic effect caused by burning or thermal decomposition, through the development of a sound empirical method which could be applied to all of the materials. On this basis, it was decided to modify the Navy flame resistance test for thermosetting plastics to render it applicable to the determination of the toxic, gases evolved when this test was employed. A wide variety of materials was tested, both molded and laminated, to cover the types commonly used by the Navy in electrical applications. Toxicity determinations were conducted at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Parallel tests, to determine the flame resistance of the materials, were conducted at the Material Laboratory, U. S. Navy Yard, New York, N. Y."

Oct 1, 1947

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968

By Dana C. Reinke

Jan 1, 2005

By S. J. Schatzel, W. P. Diamond, F. Garcia

Methane explosions have historically been one of the major causes of fatalities and injuries in underground coal mining operations. Advanced numerical models and predictive modeling approaches have the potential to offer optimized methane control solutions for general mine planning purposes and to address specific methane-related operational problems. This paper describes the development of reservoir models for the longwall mining environment and their application for investigating the influence of various completion design parameters on the methane drainage effectiveness of gob gas ventholes. The influence of increasing longwall panel width on the effectiveness of current gob gas venthole completion and placement strategies in the Pittsburgh Coalbed were evaluated and optimized designs developed to capture the expected increase in methane emissions on the larger panel.

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By O. C. Blade

The use of Diesel fuel as a source of power is continuing to increase in the United States. The latest available figures indicate that refineries are delivering in excess of 10,000,000 barrels of this type of fuel per month. Factors contributing to this increased consumption are conversions by a number of railroads from steam to Diesel locomotives and the growing use of Diesel engines in buses, trucks, tractors, earth-moving machinery, water craft, and stationary power plants. The increasing importance of Diesel fuel has led to a need for more information on its characteristics, particularly on the grades and qualities currently being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under a cooperative agreement, are conducting annual surveys of Diesel fuels produced in refineries in this country. Samples of Diesel fuel were analyzed by the manufacturers in accordance with instructions from the Motor-Fuels Survey Panel of the Automotive Research Committee of the American Petroleum Institute. Results of the analyses were transmitted to the Bureau of Mines where the data were studied am compiled as shown in the tables of this report. The first survey was made in 1950 and was published as a Bureau of Mines report. The present report shows the results of a similar survey made during 1951.

Jan 1, 1951