Search Documents

By B. W. Gandrud, G. T. Bator

The recent introduction of small coal jigs in Alabama to meet the needs of truck - mine operators for cheap and economical cleaning equipment marks another step in Alabama's pioneering record in the mechanical cleaning and preparation of coal . During the past 4 or 5 years a number of these small jigs , with capacity of 5 to 10 tons per hour , have been installed at Alabama truck mines and at a few truck mines in Illinois , Tennessee , and Pennsylvania . Most of the installations have been at mines that specialize in the production of domestic , stoker coal . This report describes three models of small jigs and includes performance data obtained recently on one of the models by the Bureau of Mines, United States Department of the Interior , in cooperation with the University of Alabama, Tuscaloosa , Ala . , for the purpose of comparing it with fullsize jigs on a performance basis . With literally hundreds of truck mines now in operation throughout the country , it has been assumed in preparing this report that there is widespread interest in the availability of small - scale inexpensive preparation equipment for use at such mines in the production of steam and domestic coal and in some instances coal for manufacture of coke . Practically none of the coal from Alabama truck mines is scld to coke - oven plants ; but in some sections of the country truck mines supply a considerable amount of coking coal, and the use of small, inexpensive washers at some of them might be very advantageous during the present war emergency from the standpoint of increasing pig - iron production through improvements in coke quality .

Aug 1, 1943

By K. C. Strebig

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory with a drill instrumented to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation, and an equation representing the bit performance was derived from the mathematical theory of reliability. The coefficient of friction in drilling increased with the use of additives, although the wear coefficient decreased. The decrease in wear associated with an increase in energy per unit volume consumed and the increase in penetration rate resulted in a net decrease in the cost per foot of drilling. A hypothesis explaining the effects achieved with the additives is given.

Jan 1, 1971

By Seymour Wasserman

To develop noise control designs for secondary crushers in Taconite plants. Taken into consideration: 1. Acoustical criteria 2. Day-to-day operational considerations and maintenance accessibility 3. Materials of construction 4. Adaptability of design to other Taconite plants having crushers 5. Cost of noise control treatment.

Jan 1, 1977

By J. M. Gomes

The Bureau of Mines, as part of an effort to maximize minerals and metals recovery from domestic resources, has investigated the feasibility of recovering heavy minerals as byproducts from sand and gravel, placer gold, and industrial mineral operations in northern California. Sand samples from about 50 locations were treated by gravity separation to yield heavy-mineral concentrates (black sands). Mineral compositions of the concentrates were determined by chemical analysis and mineralogical examination. Individual zircon, ilmenite, magnetite, platinum-group metals, thoria, and silica products were prepared from heavy-mineral concentrates by selective separation using low-and high-intensity magnetic, high-tension, and flotation equipment.

Jan 1, 1979

? CAGER, CAGE RIDER, CAGE TENDER, SHAFT MEN All of the above job titles are variously associated with the handling of men and material at hoist stations. Generally, these classifications of personnel are involved with riding cages with personnel and in hoisting supplies into the mine. Job titles and activity description will be defined in the respective chapters. ? FLOW CHART SYMBOLS [Vertical Transportation Horizontal Transportation Storage Operation Delay ]

Jan 1, 1975

By Quintin A. Aune

This report presents the results of a field and laboratory study by the Federal Bureau of Mines, in cooperation with the California Division of Mines, of the swelling-type bentonite deposits in the Vallecitos area in San Benito County, Calif. The purpose of the study was to learn if these large deposits contain bentonite of sufficient quality and quantity to be of economic value as an oil-well drilling mud additive. Large amounts of bentonitic clays are used by the petroleum industry as well as the steel industry in California. Additional amounts may be required in the near future as a concrete or earth-fill admixture in constructing dams and canals in the California Central Valley. Depletion of some local clay deposits and loss of others to military installation areas have given new emphasis to the need for developing new bentonite deposits in California.

Jan 1, 1959

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By D. R. Brooks

The Bureau of Mines has tested a dewatering technique for phosphatic clay waste. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen or trommel. In field tests conducted in central Florida, clay wastes containing approximately 4 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO-treated material will dewater to 30 pct solids in 80 days. Pretreatment of phosphatic clay waste with lime lowers the PEO dosage required for dewatering.

Jan 1, 1986

By John C. Machisak

Statistical data on injuries in the metal and nonmetal industry of the United States first became available to the Bureau of Mines by collecting reports from the operators for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1954, is the 31st publication (1933-34 was published as Bulletin 398) containing statistical data on injuries at metal and nonmetal mines and related plants, and it 1s the first such bulletin to be published since 1942. The last publication was Bulletin 461, Metal and Nonmetal-Mine Accidents in the United States, 1942. The unpublished statistics for 1943-53 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries and related employment at metal and nonmetal mines, but there is no Federal law that compels operators to submit such information. Therefore, all materials submitted are voluntary responses to the Bureau's requests for information. The figures presented herein may not be complete for the entire industry, nevertheless, every effort has been made to make them so, and the data given are believed to be representative of the hazards to which metal and nonmetal workers are exposed. Moreover, the figures are comparable as between States-which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1957

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

By Nicholas Kyriazi

It is of interest to know how to obtain as high an absorption efficiency as possible from a CO2-absorption canister used in closed-circuit breathing apparatus. In this study the Bureau of Mines found that varying the bed depth and the cross-sectional area of a canister changes its absorption characteristics. In tests using four ,1 rectangular, variable-depth canisters with different cross-sectional areas, the Bureau found that, given a constant weight of the chemical absorbent, LiOH, and a constant COa input, the canisters with a greater cross-sectional area reached C02 levels of 0.5 volume-percent in the effluent gas sooner than did the canisters with a greater bed depth. However, resistance to flow through the canister increases with bed depth, and a trade-off is inevitable. It was anticipated that the efficiency of a canister would increase with increasing intergranular air space approaching the tidal volume of the breathing waveform and then level off at some point under 100 percent. This postulation was partially substantiated. Cylindrical and radial canisters were also tested and compared. It appears that shape is not as important a factor in absorption efficiency as bed depth, since neither canister differed significantly from the rectangular canisters with regard to absorption efficiency values.

Jan 1, 1980

By L. A. Neumeier

The Bureau of Mines evaluated the properties of a Zn-0.75 pct Cu-0.12 pct Ti alloy extruded at temperatures between 400° and 720° F. The extrusions were made with a reduction ratio of 28-to-l and at relatively slow speed. Rod was also extruded at 560° and 640° F with a reduction of 255-to-l. With increased extrusion, temperature, extrusion pressures decreased substantially and creep resistance of the rod improved significantly. Coefficients of thermal expansion were low in the long rod dimension. Microstructures, hardness, and tensile properties were also evaluated, and a limited evaluation was made of bend ductility at 32° F for the rod extruded with the 255-to-1 reduction.

Jan 1, 1969

By J. S. Browning

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from potash companies operating in the Permian basin near Carlsbad, N. Mex. These ores, containing 14 to 19 percent K20 and 3 to 5 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high clay content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions for clay disaggregation and removal as opposed to strenuous attritioning. Bench-scale beneficiation techniques for recovering potash minerals by flotation from the scrubbed material resulted in acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 59.6 to 60.4 percent K.0 values can be obtained. Continuous pilot plant beneficiation techniques for recovering potash minerals by flotation resulted in concentrates containing 58.8 to 59.8 percent K20 with recoveries of 69.7 to 81.4 percent of the K20.

Jan 1, 1975

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the mining laws of French Indo - China is a translation of an article published by the Department of Mines of Indo - China ; 4 and it is released subject to correction and amplification by the proper American foreign- service officers .

Mar 1, 1933

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

By H. D. Pallister

A review of? reports and literature on the pyrite deposits at Pyriton, Ala., indicated that a large tonnage of pyrite, some of which contained a small amount of copper, had been mined and shipped to fertilizer plants throughout the South. The information contained in this literature tended to demonstrate that the ore occurred in separate lenses of greater or less extent and of varying thickness and richness in pyrite as well as in copper. The outcrop being parallel with the Atlantic Coastline Railroad and just south of it makes the deposits readily accessible for shipment. Slopes could be sunk as they were in the past in the ore body if it were of sufficient grade and thickness, and the ore could be hoisted up the slope and milled close to the slope mouth with an ample supply of water from Talladega Creek, which follows the outcrop closely.

Jan 1, 1949

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Due to the difficulties of ventilating large opening stone mines, the effective dilution of diesel particulate matter and noxious gases has often been problematic. Since stone mines have large openings that develop low air resistances, and propeller fans are designed for low pressure-high volume applications, main mine propeller fans may be a feasible option for ventilating underground stone mines. This paper describes the results of a case study where researchers from the National Institute for Occupational Safety and Health have demonstrated that significant increases in total mine airflow can be achieved and the ventilation improved in a large-opening stone mine by replacing an axial-vane mine fan with two 12-ft diameter propeller fans and adding a line of stoppings. In this study, the use of the propeller fans more than doubled the air quantity from 300,000 cfm to 750,000 cfm, while operating at 50 horsepower less than the original axial-vane fan.

By G. L. Hundley

An anhydrous chlorination process has been developed by the Bureau of Mines for the production of copper, ferric oxide, and sulfur from chalcopyrite. The first part of the process is a chlorination step in which elemental sulfur and a mixture of iron-copper chlorides are produced. This paper describes the second step of the process in which the copper and iron chlorides are reacted with oxygen to selectively convert the iron chloride to ferric oxide and chlorine leaving the copper in the chloride form. The chlorides are pulverized and dropped countercurrent to a flow of oxygen in a vertical 20-cm-diam. reactor at 800° C. By leaching with brine, the copper chloride may be separated from the insoluble iron oxide and reduced to copper powder by electrowinning. It has been demonstrated that 70 to 80 pct of the iron can be converted to oxide in a single-stage operation with a chlorine content in the offgas of 80 pct. After removal of the oxygen, this chlorine could be recycled to the chlorination step. A two-stage operation will convert 98 to 99 pct of the iron in the mixture to insoluble oxides. The offgas from the second stage contains 70 pct chlorine.

Jan 1, 1974