Search Documents

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil-production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By Robert N. Roby

"The Moffet-Johnston property was investigated by the Bureau of Mines with the object of determining the presence of ore reserves that might be utilized during the war emergency. Preliminary examination was made during May and Juno 1943, as a result of which the Johnston 'tunnel was cleaned out and repaired, the .mime was surveyed, and a small program of exploration was undertaken. This report describes the work performed and presents the data obtained.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs benefication tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.The chemical and spectrographic analyses were made at Reno, Nov., under the direction of A. C. Rico, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines. The ore-dressing tests were under the direction of Rollien R. Wells, metallurgist, at the Salt Lake City laboratories of the Bureau of Mines.The author acknowledges the cooperation and assistance of the lessee of the property, H.R. Hakes, who furnished nine reports and other information.The Moffet-Johnston property is in secs. 2 and 3, T. 3 S., R. 5 W., in the Tidal Wave mining district of Madison County, Montana.The portal of the Johnston adit is near the mouth of Bear Gulch, 9 miles northeast of Twin Bridges, Mont. It is reached by an improved dirt road that serves mining properties farther up Bear Gulch. The Moffet mine and the Mountain View shaft are now accessible from the Bear Gulch road over an access road recently completed by the U. S. Grazing Service. The Grazing Service road has also been supplemented by bulldozer trails built by the Bureau of Mines.An electric-power line extends from the Montana Power Co's substation at Twin Bridges to mines at the head of Bear Gulch and passes within 200 feet of the Johnston portal.The claims of the Moffet-Johnston property were located about 1900. A report by H. V. Winchel, consulting geologist, in 1904 indicates that most of the development on the Johnston adit was completed by that date. At the time of the Winchel report, the Moffet workings had just penetrated the first ore shoot (fig. 4)."

Sep 1, 1946

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By G. S. Rice, H. O. Howarth, Greenwald. H. P.

"Electricity as a means of transmitting power was introduced in coal mines of the United States about 1891 for both haulage and coal cutting, only a few years after electrical haulage was first installed on street cars. At first, the hazards of electrical ignition ere not appreciated and the general use of open lights and black blasting powder made the possibility of electrical ignition of fire damp seem small by comparison.5 The possibility of igniting coal dust directly by electric sparks or arcs had not been considered.In the nine years prior to 1900, the progress of introducing electricity underground was slow, except that it was used for lighting shaft bottoms. Electricity had to contend with the more general use of compressed air for coal-cutting machines and, in mainline haulage, with the use of mule-teams and endless and tail-rope systems. During this period, great improvements were made in electrical apparatus, in surface installations as well as in mines. By 1900, therefore, the technique of applying electricity in mines had so far developed that it rapidly drove out the use of compressed air in coal mines because of the comparative ease of its installation and the marked economic advantages of its use over that of compressed air in practically all kinds of mining machines except percussion. rock drills.At this time, however, little thought was given to the hazard of indiscriminate use of electricity causing explosions and fires, and the possibility of electricity causing direct ignition of coal dust had not been considered. On December6, 1907, however, the Monongah, West Va. mine explosion occurred. This was the greatest mine disaster this country has over had, 361 men being killed. Although: there was much diversity of opinion, as to the origin of the explosion, many well-informed engineers concluded that the cause was ignition of coal dust do to wreckage of a runaway trip in a rope haulage entrance slope. This slope also served as a ventilating and it extended from the level of the coal bed to the surface. The runaway trip tore down electric cables and stirred up a cloud of dust when it was wrecked at the bottom of the slope. The dust was probably ignited by the electric arcing that occurred when the wires were knocked down. (Another but less probable source of ignition was the open flames of miners lamps.) From the foot of the slops the explosion appeared to have travelled into the mine, spreading as it went. If this ignition of coal dust was the origin of the explosion, it occurred on pure intake air entering directly from the surface."

Oct 1, 1930

By Jr. Oitto

A polyester-type resin and deformed-steel reinforcing bars (rebars) were used in to strengthen and to stabilize bolted, fractured wall rock along pas 1:'y. in a western gold mine. Reinforcing bars were placed in boreholes drilled into fractured rock and then were surrounded by resin pumped under pressure into the holes and intersecting fractures until the wall rock was thoroughly impregnated. Pumping and injection equipment and infusion procedures are described. Visual examinations for movement in bonded and adjacent unbonded rock were made for 3 years. Fractured walls containing resin-rebar installations were strengthened. The results suggest that resin-rebar support can be used advantageously and economically in repairing fractured or broken rock when compared with rock bolting or timbering.

Jan 1, 1965

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

Federal lands often contain extensive mineral resources and decisions affecting access to those lands are made with knowledge of the possible minerals-related consequences. Information is provided to the Bureau of Land Management (BLM) in this report for use in preparing environmental impact statements on the Western Mojave Management Area (WMMA) and the Desert Tortoise Priority Habitat (DTPH). To augment U.S. Bureau of Mines (USBM) efforts such as the Mineral Assessment of the Planned Foil Irwin Expansion, Modified Silurian Valley Alternative, San Bernardino County, California which is in progress, and the Economic Analysis of the Minerals Potential of the East Mojave National Scenic Area; California, the USBM studied mineral deposits and estimated the potential impacts of mining in a segment of the California desert; the 8.7-million-acre WMMA, an area which includes the 1.2-million-acre Desert Tortoise Priority Habitat (DTPH). In addition, this information is intended to assist administrators, legislators, and the concerned public in understanding the economic importance of mineral resources in the California desert, especially that portion designated as the WMMA. See figure 1.

Jan 1, 1993

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines (USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two for-mulations resulted in stable gels that lasted for at least 12 months in the mine. Semicontinuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both in terms of productivity and enhanced mine safety.

Jan 1, 2010

By T. A. Klinefelter

KYANITE and the related minerals sillimanite, andalusite, dumortierite, and topaz are natural aluminum silicates that can be used in production of mullite (3A1203?2Si02), a superduty refractory material. Kyanite and sillimanite are the dominant ones because of their greater abundance. The only other kyanite-group mineral presently used for mullite production is andalusite. Mullite is not an absolutely essential material as other refractories can be used in the same heat range. However, it is a highly satisfactory one. It is the only compound of silica and alumina that is stable at high temperatures. It has low thermal expansion and is very resistant to corrosive melts and to thermal shock. For these reasons mullite refractories have a much longer life than standard fire-clay refractories under the same conditions. Worldwide, excluding U.S.S.R., the refractories industry consumes about 150-000 short tons annually of kyanite group minerals and synthetic mullite.

Jan 1, 1961

By Robert W. Freedman

Vacutainers are used by the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) for sampling mine air and products of combustion. Tests were conducted on both 10-ml and 30-ml sizes to study shelf life stability during storage, pretreatment of stoppers, and handling of a wider range of compounds. A chamber was constructed to provide convenient, efficient evacuation of the Vacutainers shortly prior to use. Fixed gases and C1 ?C5 hydrocarbons could be stored for 1 week or more after sampling. Where decreases occurred (C02 and C3-C5 hydrocarbons), they were predictable as a function of storage time. An unexplained phenomenon, slow accumulation of CO in evacuated Vacutainers, occurred after a few weeks of storage. The levels were low and time dependent. Attempts to eliminate this behavior by pretreating the stoppers were unsuccessful.

Jan 1, 1976

By Ben E. Argyle

"The tungsten area in southern Mecklenburg County, Virginia, was studied by the Bureau of Mines during the period August 1944 to March 1945. The explorations were an expansion of the work done by the Bureau in 1943 in the tungsten area of Vance County, North Carolina, which joins Mecklenburg County on the south.3/Outcrops of quartz veins in the area were searched for and examined, and the only Promising showing found (a vein on the Gladys N. Taylor tract) was explored by trenching, test pitting, and diamond drilling (fig. 1).Mecklenburg County, Virginia, is in the southeastern part of the State, bordering on North Carolina,U. S. Highways 1, 15, and 58 traverse the County, and State and County roads provide ready access to most parts of the area.In 1942, Joseph and Richard Hamme discovered tungsten-bearing quartz veins in Vance County, Forth Carolina, and started mining and milling the ore. The first concentrates were shipped in July 1943. In August 1943, the Hamme holdings were acquired by Haile Mines, Inc., who continued the mining operations.The Bureau of Mines began exploratory work in North Carolina in June 1943. Reconnaissance work showed that the mineralized belt extends north-ward into Virginia. The Kimball tract, which joins the Taylor property on the north, was explored in 1943 by trenching and drilling by the R. G. Lassiter interests of Raleigh, Y. C., with disappointing results.The topography of the district is mature and characterized by wide, shallow valleys and low, rounded ridges. The main ridges trend northeast. Most of the area ranges from 300 feet to 400 feet above sea level.The relief apparently is controlled by resistant quartz lenses and the associated hard, silicified zones. The enclosing schists and granites are usually deeply weathered. Consequently, most of the quartz veins are found on the ridges."

Apr 1, 1946

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

[This Bureau of Mines report presents results of a survey of underground mining equipment and of two demonstration programs showing the feasibility If quieting; a load-haul-dump (LHD) machine and a personnel vehicle. Typical noise levels are presented for the major machine types used in underground mines, along with estimates of the noise overexposure of miners who operate or work near these machines. General principles of noise control are explained, and the application of these principles is illustrated in the description of modifications made to the LHD machine and the personnel vehicle. The noise control package installed On the persona of vehicle lowered its noise level by 14 dBA after 4 months of operation, and inspection of the LHD machine after 2 1/2 years of operation with the modifications showed its noise level 7 dBA lower than that of the unmodified machine. Noise dosimeter measurements indicated that both machines were in compliance with Federal noise regulations for a typical shift.]

Jan 1, 1980

Aid mine operators as well as mine inspectors in making quick but sufficiently accurate measurements of the rock dust content of coal/rock dust mixtures. The Problem Past research has shown that accumulations of volatile coal dust in underground coal mines can be rendered non-explosive by dilution with chemically inert rock dust (usually limestone). Consequently, rock dusting is required by law in U.S. underground coal mines. However, mine officials and inspectors have no quick and reliable means to determine whether enough rock dust has been applied to achieve a mixture that is in compliance with the law. Even the compliance tests used by the Mine Safety and Health Administration (MSHA) are slow and involved. MSHA assures that a mine has been rock dusted adequately by collecting samples from rock dusted areas of the mine and sending the samples to a laboratory for analyses of the inert-dust content. The analyses may not be completed for more than two weeks, during which time the mine in question might be inadequately protected against coal dust explosions. To solve this problem, the Bureau of Mines devised a quick, simple and reliable device that can immediately determine the rock-dust content of a mixture of coal and rock dust.

Jan 1, 1985

By Donald O. Capstick

In 1981, U.S. Bureau of Mines personnel conducted a survey of claims and prospects in the Wheeler Ridge RARE II area to determine if mineral resources or potential for resources exists at deposits in the area. Results of Bureau of Mines investigations indicate the area contains no identified mineral deposits. However, the geologic setting at the Round Valley Peak Prospect near the center of the study area is considered to be favorable for the discovery of tungsten resources with associated molybdenum and copper. Tungsten deposits, should they be present, would be expected to occur at depth in tactite at or near the calcareous rock-granite intrusive contact. Sand, gravel, and stone deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 16,200-acre (6,560 ha) Wheeler Ridge study area is 11 mi (18 km) northwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir Wilderness adjoins the study area's western boundary (fig. 1).

Jan 1, 1983