Search Documents

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By R. W. Watson

In January 1980, the Bureau of Mines initiated an experimental program to examine the fire and explosion hazards of one-hour self-contained self rescuers (SSRs). This action was prompted by a growing concern on the part of government and industrial safety officials over the potential hazards of these devices when deployed on a large scale in underground coal mines. Prior evaluation of the safety of these devices had been at best sporadic and usually limited to experimental models. The recent availability of preproduction models of a l-hour SSR fabricated by the Mine Safety Appliance Company* and a production model manufactured by Dragerwerk Ag Lubeck of the Federal Republic of Germany allowed for a more comprehensive and meaningful evaluation of their safety in underground coal mines. This report summarizes the results of a 5-month study of the potential hazards of these two items. During the course of the work, periodic progress reports were presented to officials of the Mine Safety and Health Administration and various mining organizations including the American Mining Congress, Bituminous Coal Operators of America. National Independent Coal Operators Association, and the United Mine Workers of America. The free exchange of ideas that occurred during these meetings had a significant impact on the direction of this study and a serious attempt was made to address all of the issues that were raised at these meetings. The authors are extremely grateful to the individuals that participated in defining the specific problems that could arise as a result of deploying the self-contained self rescuers in an underground coal mine environment.

Jan 1, 1980

By Thomas J. Peters

The U.S. Bureau of Mines and the U.S. Geological Survey are responsible for the evaluation of the mineral resources and potential of further planning areas included in the U.S. Forest Service Roadless Area Review and Evaluation (RARE II) program. The Bureau of Mines primarily evaluates mineral deposits and prospects within the areas. The Geological Survey naps the area's geology and conducts geochemical sampling. Evaluations are in conformance with the Forest and Rangeland Renewable Resources Planning Act of 1974 as amended by the National Forest Management Act of 1976. The Hauser RARE II area, which consists of 7,600 acres (3,100 ha) within the Cleveland National Forest, is in southern San Diego County, California. The area, which forms the north slope of Hauser Canyon, ranges between 1,600 and 3,919 ft (490 m) in elevation. It is sparsely to densely covered with desert shrubs. The area is underlain by granitic rocks of the Peninsular Ranges batholith.

Jan 1, 1983

By C. Melvin Lepper

High-resolution shallow seismic reflection methods are being used by the Bureau of Mines to map underground geologic features in coal mines. These features include faults, channel sand, washouts, rolls, and steep dips. The seismic method is proving useful for locating all of these at reasonable cost and with better definition than available with drill programs alone. This report provides a capsule description of the techniques and their application to mine planning.

Jan 1, 1976

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. This volume deals with the development of a microcomputer based training cost model (TCM) which can be used to analyze training cost implications of various types of training. The model has been developed using Aston Tate's dBASE III plus language. The computer program and a test run of the model are presented in this report.

Jan 1, 1993

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By Robert J. Hundhausen

During the early part of World War II , it appeared likely that supplies of chromite for United States industry might become critically short . As a part of the ensuing search for new sources of domestic chromite supply , the chromite - bearing black sands along the coast of southern Oregon were hurriedly investigated by State and federal agencies and by private interests , These investigations led to a decision to begin exploitation of the deposits immediately . A government stock- piling program was put into effect , a concentrator was financed by the Defense Plant Corporation , two privately controlled companies were encouraged to start mining operations , and the Bureau of Mines and the Geological Survey were authorized to search. for additional reserves of minable ore .

Feb 1, 1947

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By S. H. Lorain

This paper is one of a series being published by the Bureau of Mines describing the mines and mills and subjects related to mining in western mineral areas. Although mining districts in the Tobacco Root Mountains are numerous there is a strong similarity in the character of the ore deposits and in the climatic and economic conditions affecting mining throughout the region. Individual mines are small, but the production of lode mines

Jan 1, 1937

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By David A. Benjamin

From 1986 to 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 59,600-acre Mexican Mountain Wilderness Study Area (UT-060-054) in order to evaluate its identified mineral resources. The study area is located in Emery County, UT, about 24 miles east of Castle Dale, UT. A review of the geologic and mining literature, and a field examination identified two uranium prospects in the Wilderness Study Area, and three copper prospects nearby. One-hundred ninety-five rock samples were taken.

Jan 1, 1989

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By Karl E. Starch

This Bureau of Mines report is a background study of severance taxes on mineral production. The rates, bases, and other features of State severance tax legislation as of March 1978 are presented, as are the amounts of State severance tax collections for fiscal year 1977, Some statistical comparisons between severance tax collections, total State tax collections, and total value of mineral production in the States involved are presented to portray the relative importance of severance taxes both in State tax revenue systems and in mineral industry revenues. A general discussion of the purposes and principles of taxation, the unique nature of a mining enterprise, the various types of taxes imposed on mineral production, and the character and rationale of the severance tax and its impacts on mining firms sets the severance tax in perspective. A bibliography of materials on the severance tax is included.

Jan 1, 1979

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By Robert N. Roby

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to Department of Interior agencies and others concerned with the planning of the proposed Federal power developments within the Missouri River Basin . The present report has been designed to permit public distribution of the factual data obtained . The field investigations in Meagher County were made during tually all 1948 ; Vir- known metallic mineral occurrences within the county were investigated ; some nonmetallic mineral deposits also were investigated . The investigations cannot be considered complete , however , because some long-inactive mines or prospects may have been missed . Most of the old mine and prospect openings are caved; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

By C. J. Wilhelm

The Carthage field, in Pamela County, Tex., is one of the largest gas-condensate in respect to both areal extent and volume of recoverable gas in the United States. The field (shown in fig. 1) is approximately 25 miles long by 20 miles wide on a southwest to northeast axis and includes 306 producing wells as of July 1, 1948. 3 distinct reservoirs in the Rodessa and Sligo formations have been found in the Carthage area the two main producing zones being the Upper and Lower Pettit, less important production being found in the Hill zone. Although a small amount of commercial production has been obtained in the Travis Peak formation, it has not been included in this report. An engineering study has been made by Bureau of Mines engineers, with the ultimate objective of arriving at an estimate of the gas reserves, by application of the data made available by the operators in the Carthage field. During World War II the Bureau of Mines submitted a restricted petroleum-engineering report on the Carthage field to the Petroleum Administration for War, at which time (March 1944) the development consisted of only 19 producing wells, 7 of which were dual completions. Because of the restricted nature of the first report and the limited development at the time of writing, a more complete investigation and subsequent publication was considered advisable. Bureau of Mines engineers have made use of all available records such as electric logs, drilling-time logs, core descriptions and results of core analyses, well-completion records, and production data in developing this report.

Jan 1, 1950

By Henry P. Wheeler

H ELIUM (chemical symbol: He) is a member of a family of normally gaseous elements, which, because of their zero valence and corresponding lack of chemical activity, are called the "noble" or "inert" gases. It is a monatomic element with an atomic number of 2, and it exists naturally in two stable isotopic forms-He3, with an atomic mass of 3.0170, and He4, with an atomic mass of 4.0039. With the exception of a trace (10-6 percent) of He3, all of the naturally occurring helium is He4. Two unstable isotopes-He5, with atomic mass 5.0137, and He6, with atomic mass 6.0208-are listed by various scientists, but the existence of He5 is questioned by some of them. He6 is radioactive, with a half-life of 0.8 second. Helium was discovered in 1868 in the gaseous atmosphere surrounding the sun. Although several scientists studied the solar chromosphere that year, it is generally agreed that J. Norman Lockyer of England should be credited with the discovery of helium, which he named, deriving the word from "helios," the Greek name for the sun. It was not found on earth until March 1895, when William Ramsay of London produced a small amount from a sample of cleveite, a uranium-bearing mineral. In 1905, H. P. Cady and D. F. McFarland of Kansas found helium in natural gas produced from a well near Dexter, Kans., and for the first time a large source of helium became available.

Jan 1, 1952