Search Documents

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By Clayton A. Landsidle

There has been little change in timbering methods in anthracite mines for 75 years, and technical information on strata control is almost wholly lacking. In order to assist the industry to establish technical data, the Bureau of Mines and a Northern field operator are cooperating in underground experiments, the first phase of which has been to investigate pneumatic packing. The four principal methods of packing in mining are hydraulic, pneumatic, mechanical, and hand. The hydraulic pa caring system is believed to have originated at Shenanodah, Pa., in 1864,4/ to prevent destruction of a church by surface subsidence after underground coal mining. This method was used again in 1884 to arrest an underground fire at Buck Ridge colliery, near Shamokin, Pa. In 1901 hydraulic packing was introduced to Europe in Upper Silesia, where it gained in popularity owing to the availability of large quantities of sand suitable for flushing .5/ Hydraulic packing has a number of disadvantages. Chief among these are the softening effect of large quantities of water on the mine floor conducive to heaving action; drainage and punning costs; and the inability to fill roof cavities completely in flat beds.

Jan 1, 1953

By David P. Lindroth

The objective of this research by the Bureau of Mines was to determine the technical feasibility and associated pilot data for drying minus 1/4-in coal with microwave energy at a frequency of 2.45 GHz. The drying data were obtained experimentally on three coal types: bituminous, subbituminous, and lignite. The experiments were performed with a custom-designed conveyorized microwave oven having a continuous power capability of 12 kW. Drying efficiencies near the theoretical maximum of 1.54 kg of water per kilowatt hour of energy input were achieved for two coals and two sizes; overall drying efficiencies averaged 77 pct.

Jan 1, 1986

By A. A. Cochran

Methods of preparing small heats of steel containing radioisotopes were developed, and the techniques of stripping film autoradiography were used to detect and study the carbide and sulfide phases in titanium-bearing steels. Metallography had revealed areas of titanium sulfide and ferrite or pearlite adjacent to areas of titanium carbide and ferrite, and unidentified, irregular phases at the boundaries between these two areas. Sulfur 35 was used to deter-mine the extent of the titanium sulfide inclusions, and carbon 14 was used to delineate the titanium carbide phase. Individual radioactive areas were located with a resolution of approximately 10 microns. A general background exposure that was not correlated with microscopically visible phases was observed in the carbon 14 autoradiographs. The evidence from both sulfur 35 autoradiographs and carbon 14 autoradiographs indicated that the unidentified inclusions were sulfides rather than carbides. INTRODUCTION The use of radioisotopes to facilitate the work at the Rolla Metallurgy Research Center was expanded in fiscal year 1959 when the Bureau of Mines authorized the installation of an intermediate-level radioactivity laboratory. Before this time, sealed cobalt 60 sources had been employed for radiography, but no tracer work was done. The primary objective of the first experiments conducted in the new laboratory was to supplement physical metallurgy investigations of selected problems in steel research.

Jan 1, 1962

By Charles A. Sorrell

This Bureau of Mines publication reviews the structural characteristics of crystalline phases and phase equilibria data for the system NaC1-KC1-AlC13-NaF-KF-AlF3, which encompasses a large number of molten salt fluxes currently used in aluminum recycling. Its purpose is to provide guidelines for research into the relationships between molten salt compositions and their physical properties, notably vapor pressures, densities, surface tensions, and viscosities, knowledge of which is essential to maximizing fluxing efficiencies and metal recovery and minimizing hazardous emissions and disposal problems. In addition, this report describes experimental determinations of sub-solidus compatibility relationships in the system, which is of the quaternary reciprocal type, containing 12 different stable 4-phase assemblages in the solid state. The compatibility diagram serves to define the important compositional planes across which important changes in properties are likely to occur.

Jan 1, 1986

By H. W. Sheffer

Technical and economic aspects of community refuse disposal systems and their effects on the environment are identified and described. Seven landfills and two incineration systems, located throughout the United States, are reviewed.

Jan 1, 1971

By W. H. Coghill, F. D. DeVaney

"Introduction Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with no many ""inflection points"" and ""counterflexures"" that they obscure the issue.Some of the investigators have neglected the very essence of the problem, namely, the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration.Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.Grindability Characteristics When the ores are being studied the information sought is grindability characteristics (grain-size distribution) and the grindability (work required to produce new surface) of a group of ores.When the study is of the machines, several machines are used for a given ore or given types of ores, and the grinding performances of the machines are compared by a grain-size study.Table 1 gives the grindability characteristics and grindability of six substances, one of which is coal. The substances are arranged from left to right in progressing order of tons per horsepower-hour. Curves and graphs are not needed for elucidation. The secret of the ease of interpretation is the order mentioned and the similarity of the sizing analyses. Power records must be complete in grinding studies.The grinding device was a ball, plunger, and mortar called the drop weight.' It may be used to advantage when the amount of material to be tested is too small for the orthodox machines.The upper part of table 1 shows the grindability characteristics by the cumulative-sizing analyses. Note how closely the percentage weights agree for a given sieve size. The lower part shows the grindability in terms defined elsewhere. The present paper should be read in conjunction with that paper."

Jun 1, 1934

By Edgar S. Rush

This study was conducted to make a limited evaluation of experimental and standard tractor dozer blades. A field test program was conducted in the southeastern part of Kansas on strip-mined areas where the spoil banks are parallel with rest-to-crest distances between 90 and 120 ft and maximum dozing distances usually less than 50 ft. This evaluation was a part of an overall joint Pittsburg and Midway Mining Company--U. S. Bureau of Mines (USBM) Specialized Reclamation Field Test Program primarily centered on the field t sting of experimental high-volume lateral relocation blades. The three blades evaluated were the 60-ft-wide angle (A) blade mounted on two 41B tractors. a 48-ft-wide A blade mounted on two D9H tractors, and a 13-ft-wide reclamation universal (Rec U) blade mounted on a D9H tractor. In addition to the experimental blades, three commercially available blades were tested: A 20-ft universal (U) blade mounted on two side-by-side (SxS) D9H tractors; a 20-ft U blade mounted on a 418 tractor; and a l2-ft straight (S) blade mounted on a D8H tractor. The dozer blade evaluations compared measured blade performance with soil and other site characteristics and with estimated earth-moving performance rates based on earthmoving methodology that accounts for the traction and speed of the tractor. The earthmoving methodology was also validated with data collected during this program.

Jan 1, 1978

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety, is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks, supplied-air respirators (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks),2 dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch, approval tests of other types of respira- tory protective equipment are conducted by the Health Branch, These branches are in the Health and Safety Division.

Mar 1, 1948

By C. P. Mabie

This report summarizes studies by the Bureau of Mines in developing a simple method for estimating the phosphorus pentoxide (P205) content of finely ground sedimentary phosphate ores and beneficiated products. The method used involved leaching, filtration, and precipitation. The Bureau found that measurement of the volume of ammonium phosphomolybdate precipitate obtained from samples containing 16.8 to 37.7 percent P205 and the use of an appropriate calibration curve permitted estimates of percentage of P205 content accurate within ± 1.1 to ± 2.6 percent, respectively, at the 95-percent confidence limits. Incidental to mineral dressing and petrographic investigations of western phosphate ores in 1959, the Bureau of Mines undertook development of a simple process-control method for rapid on-the-spot evaluation of phosphate-mineral recovery. Because of the fine-grained and obscure character of western phosphate ores, chemical, rather than microscopic or petrographic, techniques were investigated. The described method involves acid decomposition of the ore or product, filtration, addition of ammonium molybdate reagent to the filtrate, and centrifuging and measuring the volume of yellow ammonium phosphomolybdate precipitate produced.

Jan 1, 1961

By Charles Janin, HENNEN JENNINGS

Many articles have been written on the general principles and details of gold dredging, a but it is not possible within the limits of this paper to recapitulate them, and it is thus necessary to assume some knowledge of this literature by the readers of this paper. Although the purpose of this paper is to describe gold dredging in Montana, a brief mention of some early appliances used in New Zealand, Australia, and California may serve as a world-connecting link in our consideration of the development of gold dredging. DREDGES EARLY USED IN NEW ZEALAND, AUSTRALIA, AND CALIFORNIA. Spoon dredges operated by hand were tried in New Zealand on rich spots in the Clutha River with some success as early as 1865. A dredge of this kind is shown in Plate I, A. In 1870 a modification of the spoon, operated by steam and being thus a primitive steamshovel dredge, was worked in New Zealand. Steam-shovel dredging was attempted in California as early as 1888 and 1893, and with some success in later years. The elevator gold dredge with endless bucket chain was put into operation in New Zealand in 1882. Plate I, B, illustrates a type of this dredge operated by current wheels. Plate II, A, shows a steam-operated dredge of this class, also started in 1882. In 1897 R. H. Postlethwaite, connected with the Risdon Iron Works, San Francisco, introduced the dredging practice of New Zealand into California. The first dredge built sank in the turbulent current of the Yuba. The second at Oroville, owned and operated by W. P. Hammon, proved effective and was the start in California of successful gold dredging. Since then the growth of the golddredging industry in California has been so rapid that the gold output from dredges in that State exceeds that of all other States in the Union, and, in fact, of any other country of the world, the value of the gold produced in California by dredging from 1897 to the end of 1914 having been about $71,000,000.

Jan 1, 1916

By Les A. Beckett

The Bureau of Mines has developed MULSIM/BM, an improved computer program using the boundary-element approach for geomechanical analysis of mine plans in single or multiple coal seams. This Information Circular presents the improved features of the MULSIN/BM program. The four major improvements are the following: (1) Ability to specify up to 26 material property sets. (2) A new material model capability for gob and inserted materials such as packwalls or cribs. (3) Ability to model a large area with a grid of undivided blocks and to subdivide only a specified fine-mesh portion of these blocks into elements. (4) Specification of extraction ratios for the undivided blocks. In addition, an interactive graphics mesh generator program was written to accompany MULSIM/BM. A complete user's guide and program listings are included within the appendixes. The MULSIM/BM and mesh generator programs are available on tape from the National Technical Information Service.3

Jan 1, 1988

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature; a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By Kenneth G. Skinner, Hewitt Wilson, Thomas L. Hurst

Although chromite deposits occur in California , Oregon, Washington, Montana, Wyoming , Pennsylvania, Maryland , New Mexico , North Carolina, Alaska, and the Phillippine Islands , less than 1 percent of the ore used in the United States is obtained from these deposits . Most of the ore in peacetime has been supplied by imports from South Africa, New Caledonia, Turkey, and Cuba . The mineral chromite , the most important chromium ore , is an isometric spinel with an ideal composition of FeO Cr2O3 , but commercial chromite has the variable composition (Fe , Mg) Oʻ (Cr , Al , Fe) 203. Chromite has a black color , a specific gravity of 4.4 , and a hardness of 5.5 . In thin section the color is reddish -brown to black . Chromite occurs in dunite and pyroxenitic ultrabasic rocks , which are composed of iron- magnesium silicate minerals such as olivine , saxonite , serpentine , and enstatite . These are also the gangue minerals . Com mercial ore occurs at random in the country rock in kidney- or lens - shaped deposits , which have no apparent relationship to each other . Stringers , veins , and bands often cut the country rock without regard either to fracture or to other deposits . Some beach sands , such as those in southern Oregon, contain chromite .

Mar 1, 1943

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle and Safety Guidelines developed under U.S. Bureau of Mines Contract No. JO 366003, ?Improving Man Transit Safety. This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements are embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle Is presented In Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By C. H. Schack

Although viscosity is known to be important in processing and handling finely ground urea, its effect has never been fully quantified. This report describes the methods used and the results obtained in the initial phases of a broad investigation of the influence of viscosity of water suspensions of minerals in flotation, thickening, filtering, and other mineral-dressing unit operations. Several types of vis-cosimeters were tested before reliable and reproducible results could be obtained on mineral suspensions. After the viscosimeter used in the research was calibrated and standardized, tests were made on six pure minerals to study the relationship of pulp density, particle size, crystallinity, and cleavage on viscosity. An orifice-type viscosimeter equipped with a mechanical stirrer gave as good results as other types and was more flexible, faster, and simpler to operate. The orifice-type viscosimeter, when calibrated and standardized with glycerin and water mixtures, proved satisfactory over a wide range of viscosities. The accuracy and reproducibility were reasonably constant between 1 centipoise and 200 centipoises, the anticipated range in common mineral-dressing unit operations.

Jan 1, 1957

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone 4. After completing your selection, press the start button on your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gav Internet/Gopher Server: Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gav Internet System Administrator: webmaster®usbm.gov (or contact your local System Administrator).

Jan 1, 1995

By Thomas J. Peters

During the 1982 Bureau of Mines study, 55 lode and 17 placer claims were held in the RARE II area. An estimated 150 lode claims and 50 placer claim, have been located in the study area; five were patented. There are no mineral leases. Gold has been produced from 8 lode mines and stream gravels have been worked for placer gold at 4 sites. Two suction dredges were active in stream gravels, but no significant gravel bars are identified. Identified mineral resources in the Weaver Bally area are gold and byproduct silver. The identified resources are at the Globe Mine, where approximately 33,000 tons of indicated marginal reserves (2,000 tons in the RARE II area, and 31,000 tons in the adjacent proposed Trinity Alps Wilderness) contain 0.45 oz gold per ton and probably 0.1 oz silver per ton. There are an additional 150,000 tons of inferred marginal reserves (35,000 tons in the RARE II area, and 115,000 tons in the adjacent proposed wilderness) averaging 0.38 oz gold per ton and probably 0.1 oz silver per ton. There is high potential for additional resources at the Globe Mine.

Jan 1, 1983

By Hon-Yim Ko

The properties of coal from the Pittsburgh seam, procured from the Bruceton and Federal No. 2 Mines were found to be similar. Strength and stiffness properties of Beehive Mine coal were determined and the material found to be isotropic. Mechanical, index and geologic properties of roof and floor coal measure rocks from Beehive mines were measured and correlated. Analytic formulations are given for coal creep under uniaxial loading, while triaxial creep is being investigated. Results of testing of coal model structures are compared with predictions from using several material models.

Jan 1, 1976

By Frank A. Peters

A series of evaluations is being made to determine the relative processing costs of producing metallurgical-grade alumina from low-grade aluminous materials. These evaluations include the estimated operating and capital costs as well as recommendations for additional research and development to improve the processes and to lower their costs. The design for each process is based on published work. The three processes considered in this evaluation are designed to leach alumina as aluminum sulfate from calcined clay with sulfuric acid and to remove the silica residue by filtration. The filtrate from leaching is then purified by one of the following methods: Removal of iron in electrolytic cells using mercury cathodes; removal of iron by chemical precipitation through the formation of an iron-manganese complex; or precipitation of the alumina from an aqueous-ethanol solution, leaving iron in solution. Both the operating and capital costs for these processes are higher than those for the Bayer process. For plants producing 1,000 tons of alumina a day, the estimated operating costs per ton of alumina are: Electrolytic iron-removal process........... $81.35 Chemical iron-.removal process............... 82.08 Ethanol purification process............... 86.17 The investment in mercury is not part of the operating cost since this cost is considered equivalent to catalyst cost which would not be shown. The estimated capital investments for 1,000- ton-per- day plants on a Marshall and Stevens chemical equipment index basis of 240.0 are: Electrolytic iron-removal process...... $116,775,500 Chemical iron-removal process............... 99,418,900 Ethanol purification process................ 94,210,200 These investments include the working capital but not the land for each of the processes. Included in the electrolytic iron-removal process is an investment of $4,859,400 for mercury. Investigation of other methods for removing iron, of the decomposition operation, and of the leaching operation could reduce these costs.

Jan 1, 1963