Search Documents

By J. D. Spagnola

The Bureau of Mines conducted research to obtain comparative data on the extent of reduction of galena and sphalerite with molecular hydrogen and with hydrogen from the thermal cracking of ammonia and methane at various time intervals. Galena reductions of 95 to 99 percent were obtained with H2 and with decomposed NH3 while reductions of 70 to 80 percent were obtained with cracked CH4? Sphalerite reductions of 99 percent were obtained at 1,000° C with Hz and with decomposed NBs; however, complete volatilization of the free zinc from the remaining concentrate and the subsequent recombination of zinc and sulfur vapors resulted. A promoted iron catalyst brought about a decrease of 100° C in the temperature required for complete decomposition of ammonia. It was found that H2S retards NB3 decomposition and that nitrogen retards the reduction of galena by H2? A mixture of N2 and He in about the same ratio as that obtained by the thermal cracking of NBs gave about 15 percent less reduction of galena than was obtained with decomposed NB3; this indicates that a portion of the hydrogen obtained by NBs decomposition is in an active form.

Jan 1, 1965

By Zabetakis M. G.

This Bureau of Mines report presents a brief summary of the explosion trends in United States coal mines for the past 160 years. These trends show that in spite of the overall improvements in mine safety, the number of fatalities from ignitions of methane has actually increased in recent years. Suggestions are made of procedures that can be utilized to reverse this trend.

Jan 1, 1973

By John E. Hamak

The identified helium resources of the United States were estimated by the U.S. Bureau of Mines at 617 Bcf, as of December 31, 1992. This includes 285 Bef of demonstrated reserves, 85 Bcf of demonstrated marginal reserves, and 37 Bcf of demonstrated sub-economic resources. The identified resources also include 166 Bcf of helium in inferred reserves and inferred marginal reserves and 44 Bcf in inferred sub-economic resources. The identified helium resources contained on Federal lands are approximately 172 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. Undiscovered helium resources in the United States are estimated at a most likely volume of 104 Bef, with a maximum volume of 249 Bcf and a minimum volume of 41 Bef. Also reported are 51 Bcf of helium in nonconventional and low-helium-content natural gases. Extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1992 was 3.3 Bcf. Some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1995

By S. R. Zimmerley

[In the course of a flotation investi~ntion, a siliceous gold ore was ground ir, R 'ball mill to ~inils 300-mesh. It mas found that the small mount of zlus 300-~esh mnterial had a go12 assw approximately twice that of the oricinal ors, md thst this oversize ~roduct also contained much abra?.ed iron. >!oreover, the gold assay of the abraded iron, which was separated ma~etic-dl:;, wno ei::ht tiaes tkat of the ore. These facts sug,~estsd th~t sone r3laticnshin existed between the abnormally high .gold content and the preseace of abrade4 iron. It was ciecided, therefore, to investl~ate furtkor ths acsoclation of the ;old nith the iron abraded from the balls durir-g grincing. As a nrelininary ex?rr>hent, a samy?le of siliceous gold ore 786 grolznd for 1-1/2 hours i;l 3 ball mill and the nuln was divided into two products electri~mag-etically. The racult s follow: ]

Jan 1, 1937

By Jr. Norman

Thermoelectric properties of depleted uranium selenides and tellurides were investigated from room temperature to 700 C. Several depleted uranium monoselenides and monotellurides were doped with selected cationic and anionic materials to determine the effect of impurity additions on the thermoelectric properties. The undoped uranium selenides and tellurides were semimetallic conductors exhibiting low Seebeck coefficients and electrical resistivities. Partial or complete degeneracy was in evidence, indicating a charge carrier energy distribution similar to that in a metal. Doping increased the Seebeck coefficients of the uranium monoselenides and monotellurides; however, the corresponding change in the power factor in the figure of merit was small because of the increase in electrical resistivity.

Jan 1, 1965

By D. J. MacDonald

As part of a U.S. Bureau of Mines program seeking improvements to the Bayer process, a typical Jamaican bauxite was heated at temperatures up to 500° C in hydrogen, and its leachability under Bayer process conditions was measured and properties of its leached residue were observed. The objectives were to find ways to decrease the amount of organic carbon in bauxite or in leach liquor derived from it without impairing its leachability, and to improve the leached residue's filterability. Techniques employed included heating bauxite under pressure in an autoclave with hydrogen, and in flowing hydrogen at ambient pressure in a tube furnace. Leaching tests were done with a 600-mL stirred reactor. In some of the leaching tests, ferrous sulfate (FeS04) was introduced before leaching to produce a partially magnetic product. Results showed that exposure to hydrogen at temperatures from 160° to 360° C progressively diminished the bauxite's content of organic carbon and decreased the ratio of organic carbon to aluminum in leach liquor, an improvement that would allow a process using hydrogen-treated bauxite to be operated at a smaller recycle ratio, thereby consuming less energy and allowing greater throughput for a plant of given capacity. The bauxite's leachability was not impaired by high-temperature pretreatments, except at temperatures higher than 280° C. Pretreatments in hydrogen produced black, partially reduced bauxite which upon leaching gave a residue that was attracted to a magnetic field and was amenable to separation from green liquor by a magnetic filtration method.

Jan 1, 2010

By C. Ortuglio

The Bureau of Mines developed equations to determine the relationship of yields and products obtained from BM-AGA carbonization in 13-and l8-inch-diameter retorts. The developed equations indicate that results of carbonization in l8-inch-diameter retorts can be predicted from results obtained with l3-inch-diameter retorts.

Jan 1, 1966

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By J. J. Drost

This Bureau of Mines investigation studied the effect of thermal treatments upon concentratability of a western Mesabi Range nonmagnetic taconite ore and is a sequel to Bureau of Mines RI 7567. Magnetic tube tests were used to develop the data needed to calculate separation efficiency, the primary measure of concentratability. A horizontal tube furnace was employed to heat treat and reduce the hematitic ore samples. The two variables studied were roasting temperature and cooling method. The manner of cooling, either by slow cooling or quenching in water, produced no significant difference in concentratability. Roasting temperatures employed ranged from 500° to 1,000° C, and a temperature of 650° C effected the best concentratability. The temperature of 650° C correlated with the most effective roasting temperature for grindability.

Jan 1, 1973

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines (USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two for-mulations resulted in stable gels that lasted for at least 12 months in the mine. Semicontinuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both in terms of productivity and enhanced mine safety.

Jan 1, 2010

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976

By Irving Hartmann

Rock-dusting of coal mines is a most important safety measure for preventing or limiting the propagation of explosions. The Bureau of Mines has recommended for many years that rock dust be distributed on the top, ribs, and floor of mine entries and other workings of all bituminous coal and lignite mines in sufficient quantities to maintain the incombustible content of the dust above the minimum requirements. Rock-dust barriers constitute a secondary safeguard used occasionally to complement generalized rock dusting at entrances to panels and side entries or at other locations. In general, rock dust can be applied effectively with modern rock-dusting machines. However, in thin coal beds, in certain back entries, and in some other areas, rock-dusting machines cannot be used conveniently. Furthermore, many small mines find the purchase of machines costly. In such cases, rock dust is not used at all, or else it is distributed by hand, a relatively slow and costly procedure. In recent years some coal mines have started applying rock dust with the aid of permissible explosives. This may be done in various ways. One method consists in placing a stick of explosive on the floor of a room or entry midway between the ribs and covering the stick with two bags of rock dust that are slit on top and set crosswise one above the other. The explosive is then fired, causing the rock dust to be distributed on the nearby roof, rib, and floor surfaces. The procedure is repeated at desired intervals until the entire area is rock dusted. The method is claimed to be rapid, safe, and inexpensive.

Jan 1, 1950

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945

By J. B. Gayle

A 1/2-ton experimental coke oven was installed ac the Bureau of Mines Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial slot-type ovens. Because of the small force exerted on the oven walls in most tests conducted to date (probably owing to the practice of charging coals and blends at a moisture content approximating that normal to commercial plants operating in this district), little information has been obtained about expansion properties. Two sole-heated ovens have therefore been constructed and used as supplementary equipment for determining the expansion properties of coals tested in the Tuscaloosa oven. The reasons for constructing the Tuscaloosa oven, the details of design, the operating, characteristics of the oven and the reproducibility of results have been discussed in previous publications. 3 4 5/ The present report deals with the effects of substituting various high- and low-volatile coals for components of a selected base blend carbonized under conditions similar to those normally used for producing foundry coke. Results of tests of 11 coals and 14 blends indicate that several blends tested rave cokes having physical properties very similar to those produced from the reference blend.

Jan 1, 1957

By W. W. Graff

This paper describing the mining practice at Mine No. 5 of the Marquette range, Michigan, is one of a series being prepared by the Bureau of Mines on mining practices, methods, tend costs in the various mining districts of the United States. The top-slicing system of mining, has been used ever since the present operating company took control of the property in 1903, the main level and sublevel layout being chanced only as local conditions required and the use of mechanical equipment increased.

Jan 1, 1930

By J. R. Thoenen

Occurrences of titanium, zircon, and other heavy minerals are widespread in Florida. Deposits concentrated as "heavy sands" by wave and wind action have been mined an or near Atlantic coastal beaches since 1916. An important inland concentration at Trail Ridge; .believed, to have formed along an ancient share line, was disclosed by preliminary investigations (1947) by the Bureau of Mines. This report describes investigations to determine the extent and grade of "heavy-sand" concentrations in other inland stabilized dune areas in the central and northeastern parts of the peninsular region of the State (fig. 1). Portions of the central highlands south of Trail Ridge and terraces and dunes in the coastal lowlands region, east and northeast of the ridge were investigated. Holes were drilled in 10 areas (see table 1 and fig. 2) along State and County roads and on private property. They were spaced 250 to 2,000 feet. apart to obtain a cross-sectional picture of "heavy-sand" content in the dune areas. These sections were generally placed in east-west directions normal to the general trend Of the peninsula to intercept one or more of the ancient shore lines in the various areas (figs. 3 to 13, incl.). A total of 433 drive piped and 333 jet holes were drilled, and 7,293 bulk and core samples were taken. Intermediate holes were placed at closer intervals when field analysis indicated 1 percent or more of heavy minerals present. All of the holes drilled and the analysis of samples that contain 1 percent or more of heavy minerals are listed in table 2. Profiles (figs. 14 to 20, inclusive) show the more favorable concentrations, which are irregular in outline and erratic in mineral content. The highest concentrations averaged 1.0 to more than 2.0 percent heavy-mineral content, but a few individual hole samples exceeded 3.0 percent in grade.

Jan 1, 1949

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By Robert J. Hundhausen

During the early part of World War II , it appeared likely that supplies of chromite for United States industry might become critically short . As a part of the ensuing search for new sources of domestic chromite supply , the chromite - bearing black sands along the coast of southern Oregon were hurriedly investigated by State and federal agencies and by private interests , These investigations led to a decision to begin exploitation of the deposits immediately . A government stock- piling program was put into effect , a concentrator was financed by the Defense Plant Corporation , two privately controlled companies were encouraged to start mining operations , and the Bureau of Mines and the Geological Survey were authorized to search. for additional reserves of minable ore .

Feb 1, 1947