Search Documents

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933

By Arcy R., D&apos George

A process for removing sulfate from Great Salt Lake brines and other natural brines, including sea water, has been developed. Sulfate is quantitatively removed by precipitation as barium sulfate in a cyclic process employing ion-exchange techniques. Barium is continously recovered and recycled, and sodium carbonate and sulfur or sulfuric acid are produced as byproducts in quantities sufficient to more than defray the cost of desulfation.

Jan 1, 1967

By T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±5% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Titan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 1, 1978

By G. R. Fitterer, C. H. Herty

"INTRODUCTION Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis in easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot—top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel.For a large tonnage of steels which go into articles manufactured by deep—drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low—carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, — that is to say, deoxidized with manganese and perhaps a small amount of aluminum, — the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper—central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low—carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel."

Feb 1, 1931

By Thomas J. Peters

The U.S. Bureau of Mines conducted a mineral investigation, and the U.S. Geological Survey did a geological appraisal of an east portion of the Bear-Marshall-Scapegoat-Swan (BMSS) RARE II area (No. A1485) to provide mineral resource information for land use planning. The Bureau of Mines' investigation consisted of a library and field search for all mineral properties and occurrences, and included a review of Teton County mining claim records. Those records showed two placer claims, the only mining-related activity known in the area. Six reconnaissance pan samples were taken in the vicinity of the two placer claims, the Lone Star and Spotted Horse, located on Hannan Gulch in 1900 and 1901. One sample contained a trace of gold, but there are no identified resources. However, the study area is in the Rocky Mountain Overthrust Belt, which is productive for oil and gas elsewhere. The entire study area is blanketed by oil and gas leases and is currently being explored.

Jan 1, 1983

By Richard J. Kline

The underground mining industry is presently using the fluid network analyzer and digital computer to analyze ventilation systems. The availability of the digital computer and ventilation programs to mining companies has escalated its use, permitting the design and modification of new or existing mine ventilation systems to be projected completely and thoroughly with consistent precision. Because the analog computer has been analyzing ventilation systems accurately for many years, a comparison of the analog and digital methods was warranted. This report summarizes a detailed comparison for one mine, based on parallel analyses by the two computer systems.

Jan 1, 1972

By Kenneth G. Broadhead

The objective of this rare-earth oxalate study by the Bureau of Mines was to determine systematically by radiochemical techniques what effects, if any, could be attributed to the several variables--temperature, digestion time, acid concentration, rare-earth concentration, oxalic acid concentration, stirring, and the presence of other rare-earth ions. A Latin Square experimental design was used to evaluate statistically some of the variables. Precipitation losses ranged from near zero to about 7 percent, and mineral acid and rare-earth concentration were the predominant factors affecting completeness of precipitation. Quantitative oxalate precipitation of the rare-earth elements was achieved by controlling the experimental conditions as follows: (1) Maintaining rare-earth concentrations above 0.01M; (2) stirring the mixture several minutes after precipitation; (3) using an adequate (two to five-fold) excess of oxalic acid; (4) precipitating at room or iced temperature and digesting for at least 1 hour; (5) avoiding an excess of mineral acid and, if possible, maintaining the pH above 2.0; and (6) avoiding excess complexing agents such as EDTA (ethylenediaminetetraacetic acid). In the past 20 years research aimed at developing more efficient separation and purification techniques applicable to the rare-earth elements and yttrium has been extensive. Common to most of these procedures has been the use of oxalic acid to precipitate this group of elements selectively. However, this particular use of oxalic acid has a much earlier origin; its application in precipitating yttrium was first reported by Mosander (8)4 in 1843. Despite long and popular employment of this technique, only limited and somewhat conflicting data are available regarding the many factors affecting the degree of rare-earth oxalate precipitations.

Jan 1, 1961

By John J. Mulligan

The Bureau of Mines investigated coal deposits at Mount Gran (latitude 76°59' S, longitude 161°07' E), Victoria Land, Antarctica, during the austral summer of 1959-60 as part of the continuing U.S. Antarctic Research Program, which is under the auspices of the National Science Foundation. The coals and associated rocks were measured, sampled, and analyzed. Five coalbeds, ranging in thickness from over 10 feet to scattered fragments of coaly material in sandstone, occur in a sandstone-coal series overlying a series of crossbedded red-buff sandstones. Both series are part of the Beacon group of sediments, and both show some evidence of pressure metamorphism. The sandstones are poorly cemented and are composed dominantly of rounded and often frosted quartz grains. The sediments have been broken and uplifted by a series of massive diabase sills. The broken nature of the sediments precluded an estimate of the amount of coal present. The Mount Gran coals are highly attrital banded anthracites and semianthracites that have most commonly a moderately dull luster but do include bright bands. Coal in contact with or near diabase intrusives is partly graphitic but shows no evidence of coking. Apparently the coal was beyond coking rank before emplacement of the adjacent intrusives. Fragments of the plant Glossopteris indica found with the coal suggest Permian age but do not prove it. The coals appear to be derived from plant remains that collected in shallow basins; individual coalbeds would tend to be lenticular bodies that formed in different places as the dominantly sandy sediments were deposited. The wide distribution of coal indicates that coal-forming conditions prevailed over much of the continent; the great thickness of Beacon sediments indicates that similar conditions may have persisted through a long period of geologic time. Generally similar coal deposits may occupy widely separated stratigraphic positions.

Jan 1, 1963

By L. D. Tracy

"This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.IntroductionThe present report covers conditions and mining royalties in District VIII of the coal fields of Illinois, as designated by the Illinois Geological Survey. The various districts have been described in the reports on the Illinois coal-mining investigations, carried on cooperatively by the Illinois Geological Survey, the engineering experiment station of the University of Illinois, and the U. S. Bureau of Mines. This district includes Vermilion and Edgar Counties, but as the coal-mining operations in Edgar County amounted to only 827 tons in 1923, the data here given have been confined to Vermilion County.A similar report on District VI (Williamson and Franklin Counties) has been issued as Serial 2722 of the Bureau of Minos.A description of geological and mining conditions, and a discussion of market and transportation facilities, have been included because these have an important bearing on the royalties specified and the general conditions of the lease.Mining ConditionsDistrict VIII is better known as the Danville district and in 1923 produced 4,177,000 tons of coal, or approximately L per cent of the total output for the entire State for that year, which was 79,300,000 tons."

Apr 1, 1926

By V. M. Benson

A simplified, routine method for determining lithium in lithium-bearing rock is presented. The sample is decomposed by repeated treatments with nitric, hydrofluoric, and perchloric acids. Since this procedure does not appreciably dissolve beryl, interference by beryllium (the principal interfering cation) is minimized for most samples. The salts are brought into solution with water and enough citric acid-ammonium citrate buffer is added to make the final volumetric dilution 0.20 M with respect to citrate. The addition of citrate greatly reduces anion interference in the hydrogen-oxygen flame, slightly increases the intensity of the lithium 671 millimicron emission line, and reduces the effect of most of the interfering cations to the extent that analytical separations are not necessary. The accuracy of results of single determinations of lithium in a pegmatite containing spodumene, lithium-bearing mica, and beryl are approximately equal to that obtained by other flame methods, INTRODUCTION This investigation was undertaken in Bureau of Mines laboratories to develop a reliable, rapid, routine analytical method for determining lithium in lithium-bearing minerals. The requirements of the procedure were that the method should be applicable to the analysis of a variety of lithium-bearing ores and test products, and the results would be reasonably accurate for materials containing 0.05 to 8 percent Li20.

Jan 1, 1961

By Thomas J. Peters

The Snowbank study area, which had been proposed as Wilderness, lies about 5 air mi southwest of Cascade, Idaho, and about 60 air mi north of Boise. The eastern boundary of the north-south-elongate study area lies 1-to 2-mi east of Cascade Reservoir; the western boundary is contiguous, in part, with the western boundary of Valley county. The 8,200-acre study area is underlain by Cretaceous granitoid rocks of the Idaho batholith. Three prospects were found in or near the study area during a library and field search. Gold occurs at one 30-ft adit, but the gold-bearing structure appeared too narrow to contain resources. Two other prospects appeared essentially unmineralized. No evidence of geothermal activity was observed. Rock in the area is not potentially useful as dimension stone because it does not split into flat slabs. To be used as aggregate, the rock would require crushing and hauling to distant markets. One of 18 alluvium concentrate (placer) samples contained free gold, worth $1.07 per cubic yard of gravel (at a $350 per oz gold price). No alluvial bars were seen; deposits were too small to contain gold resources or be considered gravel resources.

Jan 1, 1993

By Richard D. Miller

The helium resources base of the United States was estimated by the U.S. Bureau of Mines (Bureau) to be 894.6 Bcf as of January 1, 1989. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 282.4 Bcf, (2) helium in probable natural gas resources, estimated at 237.7 Bcf, (3) helium in possible natural gas resources, estimated at 263.1 Bcf and (4) helium in speculative natural gas resources, estimated at 111.4 Bef. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a classification. The depleting resources are those associated with natural gasfields that are, or will be produced for the natural gas they contain. Almost all of the helium in potential (probable, possible and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 775 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 84 Bcf There is 35 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1990

By W. A. Grosh

Records show that much of the lead produced in the Upper Mississippi Valley lead-zinc field was taken from natural openings along crevice systems at shallow horizons or at the surface. During the early history of the district, the shallow deposits were worked intensively; but in recent years the production of lead, except as a byproduct of deeper mining for zinc ores, has not been significant. Considering the methods of early mining, the character of mineralization, and the fact that galena can still be found on the surface of the old digging areas, it was reasoned that enough mineralization might remain on and above bedrock to permit, through the use of modern equipment and methods, economical re-treatment of surface material in the digging areas.

Jan 1, 1960

By H. A. Schrecengost

Information presented herein was gathered by examination of 29 fluidized-bed thermal coal dryers and by conferences with manufacturers and users of such equipment to determine what safety features could b incorporated in design, installation, and op ration to minimize fire and explosion hazards. Fire and explosion hazards are inherent in certain types of coal dryers in that high temperatures are employed; the sizes and volatility of material handled are capable of propagating explosions; and drying gases are seldom, if ever, low enough in oxygen content to prevent ignitions of dust clouds, distilled gases, or their combinations. This is especially true for fluidized-bed dryers in which the coal is dried in air suspension and in which atmospheric air is constantly introduced to temper the heated furnace gases. Occurrence of fires on hated bedplates, in dust collectors, and in hot gas inlets was common in nearly all the dryers examined. Forceful explosions which produced external effects had occurred in 11 (39 percent), and internal "puffs" or ?bumps? had occurred in at least 24 (79 percent) of the plants examined in the study.

Jan 1, 1965

By Chas. F. Jackson

The mining literature is replete with descriptions of methods and costs of operation at producing mines. To day the mine manager can find published information bearing upon almost any problem with which he may be faced. From this literature he can familiarize himself with methods employed by otter operators for coping with problems similar to his own, under more or less parallel conditions. Transaction of mining societies, publications of the U. S. Bureau of Mines, technical journals, and handbooks all afford valuable information dealing with operating methods and costs, Very little has been published, however, regarding methods and costs of equipping and developing new properties and bringing them to tae productive stage. There may be some question in the minds of many as to the value of papers on this subject, due to the great variety of conditions encountered. No two prospects are alike. Obviously, it is impossible to forecast what expenditure will be required to develop a mine from a raw prospect or even to predict whether the prospect can be developed into a productive mine.

Jan 1, 1933

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By F. H. Gibson

An investigation was made by the Federal Bureau of Mines of methods for determining phosphorus in coal, coal ash, and coke ash. Several of these methods are being considered for international standardization. As might be expected, methods and proposals from other countries for determining phosphorus differ considerably from those accepted an standard in the United States. Some of the methods differ fundamentally in principle from the American Society for Testing Materials (ASTM) standard used in the United States; others differ only in details of procedure. Because the Bureau considered that certain of the proposed methods might offer advantages in obtaining increased accuracy and precision or in decreasing the time required for making analyses, these methods were investigated, and the results compared with those obtained by the ASTM method. The methods investigated may be grouped into three types--volumetric, colorimetric, and gravimetric. All were about equally accurate and may be used alternatively. From a practical viewpoint, when only a limited number of analyses are made intermittently, the gravimetric procedure probably is the most suitable because no special apparatus or standard solutions are required. The volumetric methods are more rapid when more analyses are made. For mass production, the colorimetric methods, although requiring a suitable photometer or spectrophotometer, are more suitable because a large throughput should be feasible.

Jan 1, 1961

By F. N. Kissell

The machine-mounted continuous respirable dust monitor (MMCRDM) is a fixed-location area sampling device developed for possible use at the working face of an underground coal mine. This device, based on proprietary technology known as the tapered element oscillating microbalance, has evolved over the past eight years through a cooperative effort of the former Bureau of Mines, MSHA, and the Rupprecht & Patashnick Company in Albany, NY. The capability to measure respirable coal mine dust levels on a continuous basis, rather than depending solely on periodic samples obtained from the traditional coal mine dust samplers, has been a goal in the mining industry for nearly two decades. Recently, an extensive series of laboratory and underground tests was conducted by NIOSH with the cooperation of MSHA and coal operators to test the performance of the MMCRDM In preliminary laboratory testing, the MMCRDM seemed to work well. However, in every underground test, when compared to reference samplers placed close to the inlet, the MMCRDM failed to meet the 25% accuracy criterion specified in the contract under which it was developed. Two reasons explain this failure: First, in most tests the bias (the relative discrepancy between the average MMCRDM concentration and the average reference sampler concentration) was too great. Second, the variability of the samplers used for reference comparison was too large. Finally, the underground testing of the MMCRDMs showed that they are quite unreliable at this stage of development. In the majority of mine tests, no more than 10 shifts of data were taken before the MMCRDM failed to function properly. Major breakdowns, requiring the return of the MMCRDM to the factory for repairs, occurred on average every 28 days. To be considered mine-worthy, MMCRDM reliability must be substantially improved. KEYWORDS Dust, coal dust, dust instrumentation, dust sampling, dust monitoring, black lung, pneumoconiosis

By P. C. Good

The work reported here was undertaken by the Federal Bureau of Mines to investigate new methods of preparing high-purity metal. Tungsten hexachloride was prepared by direct chlorination of scrap tungsten metal and by treating tungstic oxide with carbon and chlorine. The resulting tungsten hexachloride was purified by distillation and reduced win: sodium, magnesium, or hydrogen. The metal prepared by these techniques was at very high purity after arc melting but of variable quality prior to arc meIting. Metal recovery ranged from about 40 to 90 percent of theoretical values, It was found possible to deposit a smooth, dense coating of high-purity tungsten on the inside of a heated tube by vapor-phase reduction of tungsten hexachloride at reduced pressure.

Jan 1, 1961

By A. Gene Collins

Rapid, sensitive, and precise methods of determing major, minor and trace constituents of oilfield brines are needed. Several methods have been developed or adapted by the Federal Bureau of Mines at the Petroleum Research Center, Bartlesville, Okla. The following methods are described in this report: Spectrophotometric and volumetric for iodides and bromides; potentiometric for pH, alkalinity, acidity, borate boron, total boron, and organic boron; gravimetric for potassium; disodium ethylenediaminetetraacetate (EDTA) volumetric for total hardness, calcium, and magnesium; spectrophotometric for fluorides; and color comparison .for arsenic. Adequate sensitivity, precision, and accuracy were obtained for each method. The Bureau of Mines pioneered in research on the analysis of oilfield waters (2, 46, 47).6 However, several of these early procedures were quite time consuming. Also, they did not include methods for determining trace and minor constituents of brines.

Jan 1, 1961