Search Documents

By D. Harrington, M. W. Von Bernewitz

Sections 120 and 121 of Article XI. Fire Control, of a proposed Mine Safety Law in preparation, to be used as desired and when approved by any State, contains these provisions: After the adoption of these regulations, no mine operator shall erect any nonfireproof structure within 50 feet of any mine entrance. or airway. Every operating mine having nonfireproof structures within 50 feet of any mine entrance or airway, except headframes necessary for hoisting, shall have such structures fireproofed or removed and replaced with fireproof structures within six months of the adoption of these regulations. Before reopening, mines idle at the time of the adoption of these regulations shall have all non- fireproof structures fireproofed, removed, or replaced with fire- proof structures as required by the foregoing sentence. Upon receipt of the written statement of a mine operator that the fireproofing of existing structures is impracticable, the chief mining engineer (of the State commission) shall satisfy himself as to the abouracy of the statement. If he concurs that fireproofing is impracticable, and if at the same time he holds the opinion that adequate protection can be provided otherwise by such procedure, he shall have authority to issue a written permit for the substitution of fireproof door at or near portals of mine openings and collars: of shafts. Such doors shall fit as nearly gas-tight as possible. and shall be installed in such a way that the mouths of mine open- ings can be closed readily from outside of structures. The effec- tiveness of such permit may be made contingent upon the operator's continued compliance with any additional precautions which are necessary in the chief mining engineer's opinion to protect the lives of miners.

Mar 1, 1932

By W. W. Adams

Every man-hour of work performed in and about the coal mines of the United States had a 2-percent heavier death load from accidents in 1938 than in 1937. This is an unorthodox way of stating that the death rate per million man-hours of exposure or employment was 2 percent higher in 1938 than in 1937, increasing from 1.74 to 1.78. Thus the average miner had a 2-percent greater chance of being killed in 1938 than he had in 1937. The average quantity of coal resulting from 1 man-hour of work increased 3.6 percent -from 0.615 ton in 1937 to 0.637 ton in 1938. The production of the average ton of coal was accompanied by a slightly smaller loss of life in 1938 than in 1937, the accident rate being 2.793 per million tons in 1938 compared with 2.833 in 1937.

Jan 1, 1941

On September 4, 2007, Mine Safety and Health Administration, in alliance with the International Union of Operating Engineers and the International Association of Bridge, Structural, Ornamental, and Reinforcing Iron Workers, presented the first annual Mine Construction Maintenance and Repair?s Safety Contractor of the Year Award to Artisan Contracting, Inc., of Cape Girardeau, MO. Eligible contractors located throughout the United States were nominated. Artisan Contracting was nominated by Illinois Cement Company located in LaSalle, IL. Illinois Cement Company is a Division of Eagle Materials Inc., located in Dallas, Texas. Mr. Larry Frankum President of Artisan Contracting Inc., stated, ?While it is gratifying to receive a wonderful award such as this, we must not forget how fragile a good safety record is. We must constantly remain diligent in pursuit of maintaining safe work sites.?

Feb 1, 2008

By L. C. IlsLey

"There are two general classes of accidents that prevail in and about mines, namely - (1) those that through the nature of mining work can only be lessened, and (2) those that by proper precaution can be eliminated altogether. Explosive accidents that ordinarily take place while explosives are being transported in and about mines belong to the second class, that is, by proper care all such accidents can in general be avoided.The following table gives a brief summary of several accidents and disasters that have occurred in the United States and indicates the need of universal preventive measures as a basic part of all State regulations.ACCIDENTS AND DISASTERS OCCURRING WHILE TRANSPORTING EXPLOSIVES.***"

Sep 1, 1923

By Charles H. Parr

A testing program was conducted to determine the suitability and reliability of adhesives and polycarbonate lenses for extended use in luminaires in mine environments. Polycarbonates were exposed, for periods up to 36 months, to four environments including ultraviolet light, humidity, intermittent water spray, and heat of either 180°F or 407 in various combinations. Rod impact tests on the exposed lens material indicated, that polycarbonate functions well under all 180°F environments and could be used with confidence for periods exceeding the test period, for as long as ten years, with a suit) able safety factor employed in design. The specimens exposed at 240°F showed decreased toughness after 24 months' exposure. Extrapolation of these data was deemed to be risky. A 462-day compatibility test between polycarbonate and six hydraulic fluids was run on stressed PC beams. One fluid caused beam breakage in less than one day, while three caused breakage at intermediate times. Two fluids exhibited essentially no effect on the PC when compared to a control. Epoxy and silicone adhesives were tested as lens adhesives and sealants. Three epoxy combinations tested showed low and erratic failure stresses. A room-temperature-cure silicone adhesive functioned extremely well for time periods up to 36 months and temperatures u2 to 240°F.

Jan 1, 1985

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By Michael D. Balen

This Bureau of Mines open file report is one in a series of reports written about the Valdez Creek Mining District (VCM D) as a result of the continuing Bureau of Mines mining district evaluation program. This report presents the results of order-of-magnitude mining feasibility studies. The mining feasibility studies were conducted for mineral deposit models that were based on real and hypothetical deposits that occur in the VCMD. A total of 6b mine models were developed for application to the mineral deposit models. The goal of the feasibility study was to determine the monetary value per unit of minable ore that would cause the simulated cash flow for each of 66 mine models to achieve certain pre-defined rates of return for the invested capital.

Jan 1, 2011

By L. R. Burdick, J. F. Barkley

"The agglomerating index of coal is an index based upon the nature of the coke residue left when the standard volatile-matter determination of the well-known proximate analysis is made. In this determination a small amount of coal is heated in a container to about 950° C. (1,742° F.), at which temperature the volatile matter is driven off, leaving a coke formation. The coke residues for various coals are quite different in physical structure: and, for some time past, work has been done on studies of the nature of these residues in connection with the coking of coal. In 1934 Gilmore, Connell, and Nicolls proposed use of the agglomerating index for indicating the dividing line between noncaking coals and those having weakly caking properties. 4/ Its use was adopted in the standard classification of coals by rank as a requisite physical property index to differentiate semianthracite from low-volatile bituminous coal and also high-volatile ""C"" bituminous from subbituminous ""A"" coal, as shown in table 1, the standard coal classification adopted by the American Society for Testing Materials and the American Standards Association. 5./In studying the agglomerating properties of coals based on the coke residue the Bureau of Mines has adopted the notation given in table 2. Coals that in the volatile-matter determination give a coke residue either in the form of an agglomerate button that will support a 500-gram weight without pulverizing or a button that shows swelling or cell structure are considered to be agglomerating."

Nov 1, 1938

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By Boyd Guthrie

Methods of distilling topped crude oils and distillates under vacuum, accompanied by good fractionation, have taken a place of major importance in the refining industry. In the refining of petroleum products it is generally desirable to produce a distillate of good quality, and this objective is attained by fractionation of a high degree. The laboratory and commercial practice have proved that by varying the amount of fractionation the quality of the distillate can be changed, and refiners are cognizant of the advantages of good fractionation. Distillation under high vacuum, however, is a relatively new practice in petroleum refining, and only during the last few years has there been an indication that this method may become a general practice in the industry. Vacuum distillation offers many advantages over older methods of distilling petroleum products. Vacuum combined with steam distillation, for example, is replacing straight-steam distillation because the quality of the products of vacuum and steam distillation surpasses that of those produced by straight-steam distillation. Although the injection of varying amounts of steam in a vacuum unit is common practice, the amount of steam used is becoming loss as the vacuum within the unit is increased. This report describes the construction of a visible-action laboratory batch still and fractionating column and gives certain data pertaining to the operation of the apparatus under vacuum for the production of lubricating distillates. The apparatus was designed and built to produce lubricating distillates under as nearly ideal conditions as possible, in order that a subsequent study of the characteristics of the distillates could be made. For example, a study could be made of the distillates obtained up to the point of cracking of the charge if a topped crude were charged to the still; if the still was used as a rerun unit for lubricating distillates a study of nearly the entire charge could be made. Only topped crude has been charged to the still so far, and therefore this paper is limited to the results obtained from the distillation of such a charge. The results so far obtained indicate that such an apparatus is valuable in a study of different crude petroleums as sources of lubricating distillates.

Jan 1, 1932

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

By S. M. Shelton, W. A. Calhoun

"INTRODUCTION Discovery and development of a southwestern Arkansas quicksilver district are recent history. In July 1930 4/, a specimen was discovered near the Little Missouri River in sec. 1, T. 7S. R. 26 W., which was identified as cinnabar. In the summer of 1931, Leo Yount began prospecting for cinnabar near the Little Missouri River. In the fall of that year he operated a small three-tube retort near the present Parker Hill mines and produced several flasks of quicksilver. Yount optioned a considerable block of ground containing the best showings in the Little Missouri River area, and on February 19, 1932, he and W. C. McBride, Inc., of St. Louis, Mo., formed the Southwestern Quicksilver Co., which was the largest producer in the district until operations ceased in September 1934.The Southwestern Quicksilver Co. installed a rotary furnace on Parker Hill in April 1932, which treated ore from the three principal mines Gap Ridge, Parker Hill, and Parnell Hill. In 1934 production was entirely from the Gap Ridge and Parker Hill mines. Nothing was done at Parnell Hill except a little small-scale work on a share basis.Mercury Producers, Inc., later took an option on the holdings of the Southwestern Quicksilver Co. and in June 1935 began operations. The company produced considerable quicksilver before the lease and option were surrendered in the summer of 1936. Most of the work of Mercury Producers, Inc., was on Parnell Hill, but some work was done on Parker Hill and at the Bell prospect on ground not controlled by the Southwestern Quicksilver Co."

Mar 1, 1942

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine&apos;s investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By Oliver C. Ralston

The nonmetallic minerals work of the Bureau of Mines started with the organization of the Mineral Technology Division in 1912. A special experiment station devoted to the mining, preparation, and processing of nonmetallic minerals was established in 1923 at New Brunswick, N. J., and concentration problems on nonmetallic minerals of all kinds also were studied at the Mississippi Valley Experiment Station at Rolla, Mo. In July 1936 the Nonmetals Division was organized, and in May 1937 the Nonmetallic Minerals Experiment Station at New Brunswick, N. J., was moved to and made a part of the new Eastern Experiment Station at College Park, Md. At present the Nonmetals Division operates at three points: The Eastern Experiment Station, College Park, Md., which is headquarters for the division chief; the Southern Experiment Station, Tuscaloosa, Ala.; and the Northwest Experiment Station, Seattle, Wash., where coal washing and preparation studies are included with those on nonmetallic minerals. Sand, gravel, and aggregate work is carried on by the Mining Division, as sand and gravel preparation are intimately associated with mining methods. The Economics Branch of the Bureau of Mines also prepares occasional papers on nonmetallic technologic subjects in connection with the presentation of statistics on a particular industry and reviews of the mineral industry in foreign countries for use in the monthly publication, "Mineral Trade Notes."

Jan 1, 1937

By W. I. Garms

This paper, describing the milling practices at the Hayden concentrator of the Nevada Consolidated Copper Co. is the first of a Series being prepared by the Bureau of Mines on milling methods and costs in various districts of the United States. The Hayden concentrator is located at Hayden, Gila County, Ariz., 20 miles from the mine at Ray, Pinal County, Ariz., and approximately 1-1/2 miles north of the junction of the Gila and San Pedro Rivers. During the fourth quarter of 1928 the concentrator treated daily by flotation an average of 10,336 tons of ore containing 1.25 per cent of copper. The average recovery during this period amounted to 87.84 per cent of the total copper. The concentrates contained 19.88 per cent of copper.

Jan 1, 1930

By F. B. Tough

"INTRODUCTION Organizations formed for the purpose of conducting conservation work in oil fields, in order to conserve and prolong the supply of crude petroleum are rare and novel. Such an organization is the Rocky Mountain Petroleum Association, Denver, Colo, As our production of petroleum can no longer keep with the consumption, the plan of organization, character of work, and results obtained by this association are well worth considering. It is hoped that the results achieved in the Wyoming fields will serve to stimulate similar organizations among operators in the state or other oil fields of the United States, The Rocky Mountain Petroleum Association, Danvers Colo., was formed in May, 1919. It comprises the Midwest Refining Co,. The Ohio Oil Co., and the Continental Oil Co. These three companies entered into a cooperative agree¬ment with the Federal Bureau of Mines whereby $30,000 would be spent under the direction of the bureau, which agreed to furnish competent men, and to furnish the work and expenditure of funds. Although the financial burden for the first year's work, now drawing o a close, was carried by only three companies, they stipulated their desire that the benefit of the work should accrue to the industry, and that the personnel employed should be as zealous to assist one operator as another, without regard to whether ha was contributing to the support of the work or not."

Apr 1, 1920

By Paul M. Tyler

Graphite is an essential war mineral and for that reason has received much attention from the standpoint of national defense. During the World War the situation with respect to graphite supplies, though it never became acute, caused considerable concern. Even in peace time, however, graphite has aroused more interest than the actual size of the industry seems to warrant. Despite this wide interest the facts of the industry do not seem to be generally known. Often there has been an almost total disregard of the essential&apos; economic and technical problems involved. Long ago Bastin3 made the following statement; in a Government&apos; report: "To-day there are more abandoned mines and mills in the United States than the number in operation * * *. In the number of times&apos; some of these properties have changed hands in the course of a few years, there is a record of misrepresentation and disappointment that can hardly be equaled in any other branch of mining; and many properties have been notoriously associated with stock manipulation of doubtful character." According to one authority fully 600 graphite mines have failed in the United States, and the record shows that of all these properties scarcely a score have ever succeeded in operating for as much as a year or two. More than 40 mines have been worked at various times in the State of New York alone and at least that many in Alabama. Throughout the country, in fact, there are scarcely a dozen States in which efforts have not been made at some time to exploit graphite deposits. At the present time the list of mines that can be classed as at all active is reduced to less than ten. Failures inevitably occur in all lands of mining, but the disheartening feature of the record of graphite mining in this country is that so few ventures have even paid back the money put into them and. that none has been a conspicuous success.

Jan 1, 1929

By Michael G. Zabetakis

The autoignition temperatures (A.I.T.&apos;s) of natural and synthetic lubricants in air were generally found to decrease with increasing pressure. Of the two types of fluids, synthetic and natural, studied in some detail, the phosphate esters had higher A.I.T.&apos;s at any pressure between 1 and 200 atmospheres than the mineral oils. Most of the A.I.T. data obtained in this study obeyed the relationship predicted by Semenov&apos;s theory of ignition.

Jan 1, 1962