Search Documents

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer's effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984

By George S. Scott

The Bureau of Mines conducted ignition, flammability, and decomposition experiments on gas mixtures containing ethylene to determine its flammability characteristics at elevated pressures and ambient temperatures. Pure ethylene was found to propagate a decomposition reaction at 1,000 psig and ambient temperatures when ignited with 1 gram or more of guncotton in a 2-inch-id bomb. The decomposition products were primarily carbon, methane, and hydrogen.

Jan 1, 1965

By A. C. Johnson

The T. L. shaft of the Eureka Corp., Ltd., near Adams Hill, Eureka, Nev., was sunk in 1954 and 1955 to permit exploration and development of the lead-zinc-silver ore that had been indicated by drilling. This paper describes the sinking of the 4-compartment, vertical shaft to a depth of 1,127 feet and includes pertinent details of equipment, methods, and costs. A shaft crew of 10 men, supplemented by 13 hoistmen, topmen, carpenter, and shop crewmen, sank and timbered the 1,127 feet of shaft in 630 workdays. Total labor per foot of shaft was 107.95 man-hours. Supplies per foot of shaft included 20 pounds of explosives, 1.61 pounds of drill steel, and 200 board-feet of timber. Power consumption, including that required for pumping, averaged 3,726 kw.-hr. per foot.

Jan 1, 1958

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites. The process consists of four major steps: (1) reduction roast, (2) ammoniacal leach, (3) solvent extraction, and (4) electrowinning. Several solid-liquid separation steps are required that affect the economics of the overall pro-cess. In this study, two techniques for solid-liquid separation, centrifugation and thickening, were investigated. This report presents the results of (1) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and (2) an economic study of the two techniques, based on the requirements of a commercial-size (5,OOO-tpd) laterite processing plant. Sizing and other equipment-related recommendations, based on data from the Bureau's studies, were obtained from commercial manufacturers. The costs of thickening and centrifugation, including all the unit operations affected, were determined by the Bureau's process evaluation group. The total operating costs ~or separation using the two techniques (including depreciation on the capital cost of equipment) were found to be quite close: $17.26 per ton of laterite for centrifugation and $18.15 per ton of laterite for thickening. For centrifugal separation, the greatest cost was found to be the initial capital cost for the separation equipment; using thickeners, the greatest cost was for re-agent recovery.

Jan 1, 1984

By W. P. Diamond

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development program. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By Lloyd Williams

1. The investigation shows that the Wilder (locally known as the Bon Air No. 2) is the only known bed of commercial importance in Putnam County, although at least 5 coal horizons are known. All of the coal production now reported comes from this bed, which is found In a basin with no known coal outcrops. Further drilling in the east end of the basin should disclose the location of the eastern end of the axial trough and the lateral extent of the basin in Putnam County and adjoining areas in Cumberland County. Continuity of this deposit with that in the area in Putnam County north of Monterey is not conclusively established but may exist. 2 Known (measured plus indicated) reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot in place, are estimated at 29 million tons, as of January 1, 1953. Of this total, 28 million tons are in beds 28 inches and more thick. All born coal reserves in Putnam County me under less than 400 feet of overburden.

Jan 1, 1954

By W. M. Myers

"The continued expansion of modern industry broadens the markets for minerals and their product. With these increasing demands new uses are being found for minerals that heretofore were considered as possessing no commercial possibilities. This tendency is reflected in the nonmetallic field in a constantly increasing demand for minerals formerly considered to be of scientific interest only, Furthermore, nonmetallic minerals of established commercial importance are used in new ways in various products, and this tends to expand the markets for these minerals. Some recent outstanding developments in applications of minerals are given in the following pages.The Andalusite GroupAmong the minerals that until recently were considered of scientific interest only, may be listed those of the andalusite group. This group is composed of the three minerals, andalusite, cyanite (or kyunite), and sillmanite, which are all forms of the compound Al2SiO5 (A1203, S1O2), and are therefore identical in chemical composition, but differ in physical properties,"

Mar 1, 1924

By Jerry E. Olson

In 1986, at the request Of the Bureau of Land Management, the U.S. Bureau of Mines studied the central portion, encompassing 20,727 acres of the 32,261-acre Badlands Wilderness Study Area (OR-005-021) in order to evaluate its identified mineral resources. The study area is located in Crook and Deschutes Counties, OR, about 12 miles east from Bend. No mineral resources were identified. The area studied is underlain by Tertiary and Quaternary basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, or mineralized areas occur within or near the study area, but some sand and gravel has been removed from alluvial deposits at the east and west sides of the area. Slab lava of marketable grade and quantity was not found in the study area. None of the study area is of current interest for geothermal resources, but the eastern third of the wilderness study area is leased (1984) for oil and gas.

Jan 1, 1987

By I. AITKENS

Turquoise is prized solely for its attractive color ; it is dull and opaque , wholly lacking the brilliant luster that is the chief attraction of transparent gems . The best quality of turquoise is blue , of a soft and pleasing tone , like the color of clear sky but distinctive , as indicated by use of the term " turquoise blue . " Often its value is lessened by a greenish cast ; in many stones the green predominates . A large proportion of the turquoise that is mined is utterly worthless , so inferior and unattractive is its color . The finest grade of turquoise comes from Persia , notable from Nishapur . Large quantities have been mined in the Southwestern States of the United States , and less important deposits have been found in a number of the other States .

Sep 1, 1931

By John J. Sammarco

Light-emitting diodes (LEDs) are emerging as viable replacements for incandescent (INC)-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. This paper describes the performance of LED and INC sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and air flow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Second, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and INC sources can be magnified toward the end of a 10-h battery discharge cycle. Empirically, we have determined that after 8 h at an ambient temperature of 25 ?C, the average light output of an INC cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery, and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and air flow on the light output of an LED and INC cap lamp were conducted in the National Institute for Occupational Safety and Health Safety Research Coal Mine. The LED cap lamp yielded a vertical average illuminance improve­ment of approximately 9.5%, and the INC cap lamp yielded a vertical average illuminance degradation of approximately 4%. The differences between LED and INC cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38% more efficient than the INC cap lamp with a lead-acid battery at the end of the 10-h driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the INC light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, particularly given that the light output will decrease an additional 30% to 45% over the period of a 10-h shift. The implications of the differences between LED and INC sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and INC cap lamp visual performance research.

Jan 1, 2009

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956

By Andrew M. Leszcykowski

The Bureau of Mines (Bureau) conducted mineral investigations of the Payette Crest-South Fork area in west central Idaho near McCall, Idaho, in 1989. There are no known producing mines or mineral production from the area. Forty-seven samples were taken (stream sediment, rock. and placer); no identified mineral resources were delineated.

Jan 1, 1991

By C. A. Komar

Renewed interest in the underground gasification of coal evolves from comprehensive studies of earth fracture systems that indicate that the movement of fluids can be controlled in the coalbed. In particular, directional property studies of natural microfissure occurrence, permeability, ultrasonic velocity, tensile strength, and orientation of intervals of inherent rock weakness, together with geologic structure setting and fracture trace analysis, can predict the gaseous flow paths in the coalbed. Having this information, the dominant direction in which gases generated and/or liberated by heat would move can be determined so that appropriate well patterns can be developed. Together with advances made in drilling technology that permit long horizontal holes to be drilled through the coal seams, tests can be conducted to determine whether directional control will permit devolatilization of the coalbed and gasification of the remaining hot coke in a systematic manner to produce a low-Btu gas suited for the generation of electricity.

Jan 1, 1973

By Mark I. Copeland

Bureau of Mines researchers investigated the combined effect of copper and tin additions on the mechanical properties of hot-rolled steels. Wrought steels containing 0.2 wt-pct C and up to 0.2 and 1.0 wt-pct Sn and Cu, respectively, were made and evaluated by conducting tensile and impact tests and electron-beam microprobe and electron microscopy examination. Tin additions did not significantly affect the tensile properties of steel at different copper contents in the hot-rolled condition. Tin lowered the copper content at which strengthening by copper precipitation normally starts, 0.8 wt-pct, and decreased the strength of steel aged at 1,022° F (550° C). The most adverse effect of tin was lowering the notch toughness of steels at most copper contents.

Jan 1, 1976

By William Seymour, L. D. Schmidt

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of the Solid Fuels Administrator for War and with the advice of the Coke Production Committee indicated that production of pig iron could be increased. appreciably if present blast furnaces were supplied with a more uniform coke.4/ Nonvarying percentages of ash , sulfur , and fixed carbon in the coke , together with uniform physical characteristics , such as size , strength , and porosity , would aid the blast -furnace operator greatly in his trial - and - error methods of obtaining maximum production . With nonuniform raw materials he must employ certain factors of safety in operation , such as an excess of coke , an excess of limestone , and operation of the furnace below the maximum rate . Even so , he often has trouble from iron not being up to specifications , hot tops , high blowing pressures , furnace hanging up , etc. The more uniform his raw materials (of which coke is probably the most important) , the nearer to ideally can he run his furnace and thereby save raw material and increase production . One cause of nonuniformity of the coke produced by ordinary American plant practice is the prevailing lack of precise control of the bulk density ' of the coal charge in the byproduct oven . This report summarizes the available information on the subject of bulk density of crushed coal and its control . It includes brief reviews of some of the literature , some results obtained at plants visited by the authors , and results of a few preliminary tests made at the Pittsburgh Station of the Bureau of Mines .

Dec 1, 1943

By D. A. Rice

As part of a cooperative effort between the Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates the thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to sulfur (S°). The research described herein is focused on the latter half of the process. It was demonstrated that calcium sulfide could be converted to ammonium bisulfide (NH4SH), and that ammonium bisulfide could be oxidized by air in the presence of a catalyst, to elemental sulfur, which was adsorbed on the catalyst. Two methods for recovering sulfur from the catalyst were developed: (1) thermal treatment to volatilize sulfur, and (2) leaching the sulfur from the catalyst with liquid anhydrous ammonia. Over 90 pct of the sulfur adsorbed on activated carbon (the catalyst) was recovered by both methods. Based upon the encouraging laboratory investigations, a hydrometallurgical scheme was proposed for the overall conversion of calcium sulfide to elemental sulfur.

Jan 1, 1990

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By G. W. Birge, D. E. Wolfson, J. G. Walters

An investigation was conducted to determine the relationship between ASTM and Micum tumbler data and to develop equations that would enable the conversion of data from one test method for comparison with those determined by the other , and thereby facilitate the international exchange of data . Relative strengths of 18 commercially produced cokes were determined by ASTM and Micum tumblers and ASTM shatter test . Two of the samples were coke produced for foundry use , and two were produced in beehive ovens . The remaining 14 samples were produced for blast furnace consumption and had ASTM tumbler stabilities of 36 to 58. Statistical procedures were used to relate the three test methods and also to evaluate the effect of charge weights , top sizes of coke , and types of screens specified by the two standard tumbler procedures , square - hole wire mesh for the ASTM tumbler and punched round - hole for the Micum . A significant result was that the data obtained with like screens have a higher degree of correlation with a smaller standard deviation than data from the screens specified for each tumbler .

Jan 1, 1964