Search Documents

By J. W. Higgs

This paper, describing the operation of the Gifford Hill & Co. plant at Hoot Spur near Texarkana, is one of a series being prepared for and published by the United States Bureau of Mines on methods and costs of mining and preparing gravel and sand throughout the United States. These tapers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. Although the publication of total costs might not be advisable in some instances yet a knowledge of operating costs is essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The plant described combines some features of dredging and some of dry-pit operation, as material is excavated in a dry pit with a drag line, hauled to the plant in standard-gage cars, and then pumped. This operation should be of special interest to operators whose deposits contain a large quantity of clay.

Jan 1, 1936

By ALBERT C. DURHAM

In anthracite mining , pumping is a problem of major importance , and water must be handled and rehandled in almost every mine whether the mine is in operation or idle . The motor - driven centrifugal pump is the most commonly used type of unit for the large pumping installations, and experience has . proved that fully automatic control has certain advantages over manual control . Some of these advantages are greater safety for maintenance personnel , continuous protection against faulty operation , which could cause damage to the Lumping apparatus , and lower pump -room operating costs .

Aug 1, 1948

By F. A. Skirvin

Purification techniques were investigated for removing low-level metallic impurities from tungsten hexachloride. These techniques included distillation) fused-salt scrubbing) zone refining) and adsorption. Fractional distillation of tungsten hexachloride was found to be an effective purification method. The impurity levels of molybdenum) iron) nickel) copper) magnesium) and manganese were reduced to provide a tungsten halide sample which contained a total of less than 10 ppm detectable metallic impurities. Purification by fused-salt scrubbing of tungsten hexachloride in a lithium chloride-potassium chloride eutectic produced a hexachloride product which was of approximately the same quality as that obtained by distillation. Zone refining and adsorption did not appear to be as effective as distillation or fused-salt scrubbing.

Jan 1, 1967

By Hillary W. St. Clair

The purpose of this investigation was to determine the practicability of refining crude aluminum-silicon alloy or aluminum scrap containing silicon and iron by selective dissolution in zinc of the aluminum from the alloy followed by distillation of the zinc from the aluminum.

Jan 1, 1949

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Harrison County, W. Va. It is one in a series of Federal Bureau of Mines reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 6.5 million tons of coal was produced in Harrison County, W. Va., in 1958, of which over 3.7 million tons was cleaned mechanically in seven preparation plants. All of the coal cleaned was from the Pittsburgh bed. It has been estimated that more than 1,816 million tons of coal remains in the county in beds 12 inches or more thick. The Pittsburgh and Redstone beds were selected by the Bureau for a study based on current production rates and estimated minable reserves. Sample locations were selected following a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Six samples were collected from the Pittsburgh bed, and three samples came from the Redstone bed, Float-and-sink tests of the samples collected from the Pittsburgh and Redstone beds showed that neither coal could be upgraded to a metallurgical fuel under the standards set up for this study, even after intensive preparation. Finer crushing of the samples moderately increased the yields and slightly reduced both the ash and the sulfur contents in the 1.30-specific-gravity float fractions. Finer crushing slightly decreased the yields in the 1.58-specific-gravity float fractions, whereas it reduced the sulfur content 0.11 percent for the Redstone sample and 0.46 for the Pittsburgh sample.

Jan 1, 1961

By G. Richards Gwinn

Vermiculites are secondary minerals formed by the: alteration of biotite and philogopite mica and are associated with basic rocks such as dunites, serpentines, and pyroxenites. Vermiculite was first described by T. H. Webb in 1824. It remained a mineralogical curiosity until 1913, when the first commercial deposit was discovered in the Turrett mining district of Colorado. Expanded or exfoliated vermiculite was first marketed in 1915 from a deposit in this district 5 miles southeast of Hecla, Colo. This activity was brief, but successful and continuous commercial development began in 1921 in Montana. 'Deposits in other States have been found and developed, but Montana is by far the largest producer. Vermiculite has also been found in South Africa, Western

Jan 1, 1944

By Hillary W. Clair

An equation is derived for the rate of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing . The equation takes into consideration the reaction rate coefficient , transport through the gas and through the porous shell of reduced oxide , the rate of gas flow , and the volume of the enclosure . The equation serves as a model for predicting the course of reduction of a particle of metal oxide in a shaft furnace .

Jan 1, 1964

By W. E. Brown, P. R. Porath, V. Miller, C. E. Wood, C. Prasky, E. P. Barrett

"INTRODUCTION This investigation was a part at the Bureau of Mines program for the production of critical and essential materials needed for the war.The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from low grade ores of Minnesota.OBJECT OF INVESTIGATIONThe investigation was conducted by the Bureau of Mines to ""determine the workability of the proposed bubble-hearth process and its possible use in connection with an experimental plant for the gasification of lignite being operated by the Coal Division of the Bureau of Mines at Grand Forks, North Dakota.ACKNOWLEDGMENTSThis report is one of many on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources.Investigations of our mineral resources are conducted by the Mining Branch, L. B. Moon, chief, and by the Metallurgical Branch, O. C. Ralston, chief.The scope of the report falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficulty beneficiated ores, the production of pure metals from domestic deposits, the exploration of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice."

Jun 1, 1947

By W. D. Riley

The U.S. Department of the Interior, Bureau of Mines, has been conducting minerals recovery research in support of the nation's geothermal program since 1974. The Bureau's program of laboratory and field studies has focused on determining the materials of construction for geothermal resource recovery plants and an the recovery of mineral values from the geobrines. An analytical program has been conducted at the Avondale Research Center to determine the chemical constituents of some high- and low-salinity geobrines found in the Imperial, Valley of California. Data are reported for the early stages of brine production of femur geothermal wells--the low-salinity, medium-enthalpy brines from the East Mesa Known Geothermal Resource Area (KGRA), Mesa 6-1 and 6-2, and the high-salinity, high-enthalpy brine from the Salton Sea KGRA, Magmamax 1 and Woolsey 1. The reported results indicate the importance of the operating and engineering history, the operating parameters during sampling, and the method of sampling in order to evaluate the chemical analyses.

Jan 1, 1980

By B. W. Naugle

Twenty-nine sole-heated-oven expansion teats were made on 9 different coals, and apparent specific-Brevity tests were made on 12 of the resultant cokes. The coals, which ranged in dry, mineral-matter-free fixed-carbon content from 58.7 to 81.1 percent, were tested over a rather wide range of moisture content and dry-coal bulk density to determine the separate effects of these variables on linear coal expansion. The experimental data support the follow expression relating "as-tested" coal bulk density, moisture content, and linear expansion, [ER = (1-MR) (1+Et) - 1; BDt] where ER = fractional expansion at a reference bulk density of 55.0 lb. of 1 percent moisture coal per cu. ft., Et = fractional expansion at Mt and BDt, MR = reference moisture content = 0.01, Mt = moisture content, "as-tested", BDR = reference bulk density = 55.0 lb. per cu, ft., BDt = bulk density, "as-tested", 1b. per cu. ft.

Jan 1, 1957

Provide sound battery safety guidelines for mine workers who maintain mobile surface mining equipment. Approach Battery-related accidents account for about 5 percent of all nonfatal disabling injuries in coal and metal nonmetal surface mines. These accidents occur despite the fact that appropriate battery safety technology (maintenance-free batteries, cable removers, fault detectors, hot-jumping systems, etc.) exists. Mine operators are not always aware of the safety measures that could be taken because this safety information is widely scattered in numerous unrelated technical reports, vendor brochures, and journal articles. A literature search of these reports and a review of relevant industry standards, handbooks, and references on battery safety, followed by discussions with mining company and MSHA personnel, provided the Bureau of Mines with the background necessary to develop procedures for proper and safe battery usage. These procedures were condensed and written in nontechnical language to serve as guidelines in assuring battery safety during maintenance of mining equipment.

Jan 1, 1986

By J. A. McAllister

In the course of a study of domestic Manganese resources, 2-ton representative samples of ore were taken by Bureau of Mines' engineers from the Payday claim, Weber County, and the Newcomb-claims, Rich County, Utah. The Payday No. 1 deposit is situated 13 miles northeast of Huntsville, Weber County, Utah. The manganese ore is a. replacement deposit in limestone and consists of manganese oxides imbedded 'in clay and also as the cementing agent consolidating small pebbles and pieces of quartz and limestone.

Jan 1, 1949

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By M. J. Ankeny

This is a study of 58 fatal haulage accidents investigated by Federal coal-mine inspectors during the period January - June 1951. The information presented in this circular was obtained by analyzing fatal haulage accidents in 33 bituminous-coal producing counties representing 11 States. The physical conditions represent a cross section off producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of large modern mechanized operations. These data are thought to be representative of haulage conditions within the bituminous-coal mining industry and are submitted to follow up the Information Circular 7604 ?Analysis of Haulage Fatalities in Bituminous-Coal Mines - 1950.? Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the problem of haulage safety is complex. It is subject to constant change and is comprised of numerous influencing variables, which are not always obvious. The solution to this problem will not come through the application of any standard formula or mechanical approach since the inherent factors are strongly influenced by the human equation, and the chain of circumstances is further affected by expediency.

Jan 1, 1951

By J. E. Shelton

This presentation covers the results of laboratory studies conducted by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg., on alluvial sands from Dismal Swamp, Bear Valley, and Cascade, Idaho. The search for radioactive minerals has led to the reexamination of alluvial deposits; in the process of this reappraisal the frequent presence of minerals bearing columbium and/or tantalum was toted. Because of increased demand for these metals by the defense industries and because these industries depend upon foreign sources for their supply the domestic alluvial black sands are being considered, as a possible domestic source. However, utilization of these alluvial deposits depends upon development of methods of concentrating these valuable minerals. The primary objective of the test work was the study of the effect of attrition scrubbing, sizing, magnetic, electrostatic, and gravity separa¬tion as methods for concentrating and recovering the columbium and tantalum-bearing minerals, samarskite, euxenite, ilmenorutile, and columbite.

Jan 1, 1955

By T. E. Swigart

In the production of oil end gas, engineering methods have been applied less than in any other branch of the oil industry. While refineries, gasoline plants, pipe-line and other transportation systems, and even drilling wells to a great extent, take advantage of engineering skill, the tendency has been to assume that the handling of producing wells is merely a mechanical and routine matter. At present few companies employ engineers to study oil and gas production methods with a view of increasing the general efficiency of recovery, but in vie, of the advancement in other lines of the petroleum industry by the application of engineering principles, does it not seem likely that the production branch may benefit also by engineering studies? Engineering applied to the handling of producing wells falls under two general headings, - first, the efficient handling of wells from the time of their inception in order to obtain the greatest possible ultimate production, and, second, the rehabilitation of old properties that have been handled carelessly in their early lives. To date, the engineering work that has been done on oil production problems falls mostly in the second class. For example, the use of vacuum and the application of compressed air have proved successful in some instances in stimulating wells of low gas pressure. These methods are costly to apply and are adapted to small wells in which the gas is almost exhausted, or in which the original gas pressure is negligible. The experiments described in this paper fall under the first heading, as they were made with an idea of learning toe probable extent to which the gas production of an oil well can be curtailed while gas in the sand is still plentiful, and thus saved for doing work during the later period of a well's life. Because of the scope of the experiments, this paper does not include a discussion of back pressure on flowing wells or for purposes other than cutting down the gas produced with each barrel of oil.

Jan 1, 1922

By E. C. Lane

[This Is the ninth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the interior. The first report gave data on motor gasoline sold during the winter of 1935-36.3/ The Present report presents analytical data for 2,033 samples, representing the products of approximately 80 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data that were average by the Pacific Coast Technical Group before 'being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. The cumber of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, arc as follows: Regular price, 1,066 samples, 208 items, and 49 brands; premium price, 575 tamales, 154 items, and 38 brands; third-grade gasoline, 7;4 samples, 150 items, and 53 brands. The meanings of these terms as used in the surveys tar as follows: Sample: The individual supply of gasoline obtained at the filling station and analysed in the laboratory.]

Jan 1, 1940

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that effects the net expansion of the change in both industrial and test ovens. Various test results5/ have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; but no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors.]

Jan 1, 1940

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture filling and associated alteration on the mechanical behavior of rocks. Results are presented for specimens from the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from 1) Climax, medium-grained - granite, fine-grained granite, granite porphyry, schist, and gneiss; 2. Henderson, rhyolite porphyry; 3. San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineral composition, composition and fabric of fracture fillings, density and porosity. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic relocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Tentative conclusions are that some relation appears to exist between compressive strength and the following properties and features for all the specimens: dynamic Young's modulus, sonic velocity, density, rock composition, and composition and fabric of fracture fillings - veinlets. There appears to be some relation between compressive strength and Shore scleroscope hardness and porosity for quartz monzonite (San Manuel). A relation appears to exist between compressive strength and texture for schist and between com¬pressive strength and extent of failure on fracture fillings for fine-grained granite, schist, and gneiss (Climax). We plan to perform additional analyses of data collected so far and data yet to be collected in the next few months, with emphasis placed on devising a practical index of alter¬ation that can be used in the field. Limitations on interpretations arise from such factors as heterogeneity of the rocks studied, the small range of confining pressures used, and other factors presented in the text.

Jan 1, 1973

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956