Search Documents

By Llewellyn A. Rubin

Under Bureau of Mines Contract H0122007, Telcom, Inc., with the assistance of Fenix & Scisson, Inc., conducted a 17-month research and development project aimed at provid¬ing a field-test model of a guidance system for use with the Bureau of Mines Probe Drill. The Probe Drill is a part of the Bureau's Mine Rescue System developed under Contract H0101262. Volume I of this report is subdivided into seven sections. Volume II consists of a number of supporting appendices. In addition, there were delivered under the Contract, a number of other documents which are referenced in the text. Section 1 deals with essential contract information, Program Background, and a general system description. Section 2 covers the project chronology in brief. Section 3 is a digest of design considerations and implementation related to the requirements of the Contract. Section 4 is a description of the System, including illustrations of the hardware, and software. Section 5 is devoted to Operation and Maintenance. Para. 5.1 describes step-by-step field assembly and disassembly of the downhole unit. Para. 5.2 covers Operation. Para. 5.3 covers various aspects of maintenance from the lowest field echelon possible. Higher level maintenance must be accomplished in the laboratory, for the present field-test model. Para. 5.4 covers system calibration. Para. 5.5 covers detailed step-by-step operational sequences. Section 6 covers the results of the field testing, post-test evaluation, and recommendations. Essentially, we conclude that the present hardware (field-test model) has proven every aspect of system performance, but failed to provide reliable assurance of an operationally ready system. Telcom, therefore, recommends a three-phase continuing effort devised to provide the operationally-ready model of the system.

Jan 1, 1973

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the hydrogen cyanide (HCN) concentrations and smoke particle characteristics during the combustion of flexible polyurethane foams and other nitrogen-containing materials, for the development of a test parameter. The experiments were conducted in an approximately 2O-L furnace at set furnace temperatures of 250° and 1,000° C for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied as a function of time were the gaseous and aerosol HCN concentrations, the smoke particles average diameter (dg) and particle concentration (no), and the product of the smoke particle diameter and concentration (dgno). Carbon monoxide, carbon dioxide, and oxygen concentrations, sample mass weight loss, and furnace temperatures were also studied; analyses of nitrogen and cyanate content of the material were carried out. Results show that dgno correlates directly with the HCN concentrations, which depend on the nitrogen and cyanate contents of the material.

Jan 1, 2010

This Bureau of Mines report reviews the development of the world potash industry. The trends leading to the present market situation of oversupply arid low prices, which threaten; the domestic potash industry, are presented and analyzed. Because the major threat to the domestic industry comes from Canadian imports, the report focuses on the comparative economics of United States and Canadian production. The study resulted in these major conclusions: 1. Balance of world supply and demand is foreseeable in 1975, but it could be delayed by planned expansion. 2. Balance of U.S. supply and demand could occur as early as 1974-75 or as late as 1981. 3. Nearly all U. S. production capacity vis-a-vis Canadian competition is now uneconomic. Prices cover out-of -pocket costs for only 30 percent of U.S. production. 4. U.S. producers will be undersold by Canadians in 60 to 90 percent of the U.S. market. Canadians also will have the edge over United States and European producers in export markets. 5. U.S. firms have invested in 60 percent of the planned 1971 Canadian production, and they have large holdings in Saskatchewan. 6. The decline in the U.S. potash industry probably reduced personal income in Carlsbad, Eddy County, N. Mex, the chief potash-producing area in the United States, about $21.5 million between 1966 and 1969.

Jan 1, 1970

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmospheres .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmosphere .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By Victor Spironello

The Bureau of Mines is studying cupola ironmel technology with the objectives of conserving high-quality raw materials through substitution and productivity. In the research re-ported here, a ize was modified by a gas-fired melting and/or ing chamber into the stack above the level of the coke bed, for study as a prototype for a coal-fired melting chamber. The modified cupola, in which natural gas was used to partially replace foundry coke, was evaluated in several trial runs. Data were obtained on furnace performance, metal and slag chemistry, and scrubber waters as particulates. Results of the modified ion were compared to those of conventional cupola operation. Although this research was preliminary--since the ultimate goal is to use pulverized coal instead of yielded ample evidence that the melting rate of a cupola can be icantly increased with less than a increase in energy input. Other evidence suggests that melting of low-density scrap can be enhanced and that scrap containing undesirable and/or oxidizable elements can be appreciably upgraded. This work is continuing and will include the use of pulverized coal of low rank to assist in melting.

Jan 1, 1984

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions2 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made, Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1971

By J. A. Woolf, E. S. Leaver, A. P. Towne

"INTRODUCTION A report giving experiments dealing with factors affecting the floatation of the most commonly occurring silver minerals was published years ago. At that time we could not obtain suitable samples of many of the so-called sulfo-salts of the base metals, which are generally silver--bearing and which comprise an appreciable percentage of the natural silver ores. Since Leaver and Woolf's work was published, samples of impure tennantite and enargite have been obtained, and considerable experimental flotation work has been done with synthetic mixtures prepared from these samples. During the present national emergency, research dealing solely with the recovery of gold and silver must necessarily be curtailed. However, many deposits of strategic minerals and critical base metals contain an appreciable amount of gold and silver, the recovery of which would aid greatly in recovering the strategies by taking care of a considerable part of the cost of treatment. Because of this, the recovery of precious metals should not be overlooked entirely. As the Bureau of Mines is now utilizing all of its facilities for the development of increased domestic productions of strategic and critical minerals, this is the last report not concerned primarily with such minerals that will be published until the war ends."

Sep 1, 1942

By Thomas Fraser, J. D. Davis

"INTRODUCTION Preliminary tests of the Oyon coal constituted part of a wartime exploratory and development program in which many agencies participated. The general objective was to find new and adequate source of fuel and other raw materials for greatly expanded industry.The Oyon coal field, known for at least a hundred years to the mining people of Peru, offers a possible source of high-grade process fuel for the growing metallurgical industries of South America and the Pacific coast. Santolalla 4/ reports that low-volatile coal from this region was used in local smelting operations as early as 1850. It has been mined in very small quanti¬ties for many years and used in neighboring mining camps and villages. Small quantities are regularly used at Oroya for the manufacture of carbide, and in recent years small-scale coking operations in specially designed ovens in the region have demonstrated that these coals will make dense coke.During this long period of desultory operations many small openings have been made scattered over a wide area in this general region, indicating very extensive occurrence of the coal measures, although systematic exploration work has not been undertaken. However, current development work of the Banco Minero del Peru has opened up several substantially parallel highly inclined or vertical beds of workable thickness and has followed these deposits to sufficient lateral extent to prove fairly well the existence of substantial reserves on this property."

Mar 1, 1948

By E. P. Youngman

This paper is one of a series of digests of foreign minim legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the minim lams of Ceylon has been prey tired from the best available information in Washington and is released subject to amplification and correction, if necessary, by United States foreign-service officers. INTRODUCTION Ceylon has no basic mining law; the general rules governing the granting of mineral concessions and affecting legal titles of concessionaires are laid down in Ceylon Government ordinances or are found in the authorized forms for licenses and leases. The material available in the preparation of this digest is as follows:

Jan 1, 1933

By George L. Gates

It is generally recognized that if the lose and contamination of the fluid content of a core specimen from an oil- and gas-bearing formation in a well were eliminated, the value of core analysis would be increased greatly. In an effort to obtain uncontaminated cores, extensive field tests were carried out in the Mercy field, San Jacinto County, Tex., with the Carter pressure core barrel and an oil-base drilling fluid having very low rates of filtration as measured by the standard A.P.I. drilling-fluid filter teat. A tracer was added to the drilling fluid filter test. A tracer was added to the drilling fluid to provide a means for quantitatively measuring the volume of oil filtrate in the cores. Unfortunately, as stated in the report on the Mercy tests, very little oil nand was penetrated in coring the well; and because the performance of the pressure core barrel was not entirely satisfactory, the tests did not provide a complete answer to the question: Does a filtrate from an oil-base drilling fluid enter cores., and how does it affect the results of the core analyses?

Jan 1, 1950

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By J. G. Kirby

The total number of petroleum refineries in the United States decreased during 1951, while the total crude-oil charging capacity continued to increase. There were 350 refineries as of January 1, 1952, compared with 357 a year earlier, according to the annual Bureau of Mines capacity survey. A gain of 369,241 barrels in daily refinery crude through-put capacity during 1951 brings the total to 7,332,885 barrels daily. The capacity of the average refinery to process crude-oil was 20,951 barrels daily, an increase of 1,445 barrels daily over the previous year. Capacity added in the Texas Gulf district accounted for 36 percent of the total increase; the Indiana-Illinois-Kentucky district, 23 percent; the East Coast district, 19 percent; the Oklahoma-Kansas district, 12 percent; and the Texas Inland district, 11 percent. The California district was the only one reporting a decline in crude-oil refining capacity, the total being 14,200 barrels daily below the previous year. Reported as under construction January 1, 1952, was an additional crude-oil capacity of 282,680 barrels daily, an increase of 77 percent over the January 1, 1951, total of 160,100 barrels. The capacity now building is for the expansion of existing facilities, since no new plants had been begun as of the first of the year. Three or four companies have plans to build refineries in the Williston Basin area of North Dakota, but no definite locations or dates when construction will begin have been announced.

Jan 1, 1952

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

By Michael G. Zabetakis, Glenn H. Damon, Joseph A. Herickes

The flammability and explosibility of unsymmetrical dimethylhydrazine ( UDMH ) were investigated by the Federal Bureau of Mines to evaluate hazards associated with commercial application of this material as a missile fuel . This program included the following determinations : 1. Temperature limits of flammability in air at one atmosphere pressure ; 2. limits of flammability at selected elevated temperatures and pressures ; 3. 4 . 5. spontaneous ignition temperature in air at one atmosphere and at 200 pressure per square inch gage ( p.s.i.g. ) initial pressure ; spontaneous decomposition temperatures in nitrogen at one atmosphere and at 200 p.s.i.g .; shock sensitivity over a temperature range from about ( ca. ) 25 ° to 50 ° C .; 6. shock sensitivity of reference propellants ( hydrazine , nitromethane , methyl acetylene , etc. ) ; 7 . shock sensitivity of UDMH plus small amounts of selected metal catalysts . Part of the corresponding data was obtained for a mixture of unsymmetrical - dimethylhydrazine and diethylenetriamine ( U - DETA) .

Jul 1, 1960

By B. W. Madsen

The Bureau of Mines conducted a large-scale (6.4 t), long-term (2,165 days) test to gain a better understanding of the leaching characteristics of chalcopyritic ores. An ore sample containing 0.77 pct Cu was leached in a fiberglass column by downward percolation of acidified ferric sulfate solutions. Three sets of leaching conditions were investigated: (1) ambient temperature leaching, (2) elevated temperature (50° to 60° C) leaching, and (3) elevated temperature leaching after inoculation with thermophilic bacteria. Leaching at ambient temperature resulted in a copper extraction rate of 0.44 pct per 100 days. Increasing the temperature to 50° to 60° C resulted in decreased activity of natural mesophilic bacteria, and the leaching rate decreased to 0.22 pct per 100 days. The pH was lowered from 2.0 to 1.6, and nutrient solutions that contained thermophilic bacteria were added. This procedure resulted in an increase in the ferric-to-ferrous iron ratio and an increase in the copper leaching rate. However, the increased leaching rate was not sustained, and 120 days after inoculation the bacterial activity declined, the ferrous iron content increased, and the copper leaching rate decreased.

Jan 1, 1983

By R. O. Dannenberg

This report describes aperiments by the Bureau of Mines and reviews theoretical aspects of the use of organophosphate solvent extraction for recovering beryllium from sulfate leach liquors. The leach liquors were prepared by sulfuric acid leaching of lime-sintered low-tenor beryl flotation concentrates. The experimental work on sulfate leach liquors showed that the acidic esters of organophosphates extracted beryllium slowly but in preference to aluminum. Three common alkylphosphoric acids, di- (2-ethylhexyl) (EHPA), heptadecyl (HDPA), and dodecyl (DDPA), in order of decrmsing selectivity, yielded a partial separation of beryllium from aluminum.

Jan 1, 1962

By Industrial Research Office

"The U.S. Bureau of Mines established on August 15, 1983, the Generic Mineral Technology Center for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. The Center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to ""... permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . ."" The Center's program is designed to permit an accelerated attack on the fundamental research problems for the control of respirable dust in mines.The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. The Generic Technology Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated. The Center activities involve the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications' in the respirable dust area.The Center is composed of faculty from the four universities/institutes listed above. The personnel, facilities and equipment that are available to the Center from these entities are diverse, complementary and comprehensive. More than fifty scientists, engineers; and medical personnel in the Center are engaged in respirable dust research. Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease Studies are available as a result of the existing relationship between NIOSH and West Virginia University.The breakdown of the dust research program into the five areas mentioned above recognizes the importance of an integrated fundamental research approach to the respirable dust problem compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities. The specific projects in the research areas are a result of a careful evaluation of the past and ongoing research activities, the identification of areas where data and information are scarce, and awareness of the recommendation of the National Academy of Sciences Study on the Measurement and Control of Respirable Dust. Penn State is the administrative unit for the Center. Funding to date is nearly $6.5 million."

Aug 31, 1989

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964