Search Documents

By R. R. Brown

The Bureau of Mines undertook a limited feasibility study to determine the practicality of removing copper from automobile scrap by thermal treatment. Test specimens, prepared by wrapping bare and insulated copper wire around small steel coupons, were heated at 600° to 1,150° C in various atmospheres for different lengths of time under both static and dynamic conditions. The tests indicated that adequate removal of copper cannot be effected by thermal treatment of scrap above the melting point of copper. Tests showed that copper present in scrap as insulated wire is embrittled by thermal treatment at 800° to 900° C if the insulation contains lead, and that the embrittled copper is almost completely removed by a mechanical action such as tumbling. Also chemical pretreatment of specimens to effect embrittlement of copper and the magnetic separation of oxide scale were studied. Tests showed that bare copper can be embrittled by depositing waterglass (Na, Si409) on copper prior to thermal treatment.

Jan 1, 1968

By W. W. Adams

"A recent paper prepared by the writer summarized the results of an analysis of the accident records of 34 metal mines for the calendar year 1925. The present paper summarizes the results of a similar analysis of the accident records of 59 coal mines for the same year. This summary is based upon reports furnished to the Bureau of Mines, Department of Commerce, by operating companies that par¬ticipated in the National Safety Competition of 1925.The purpose of the Competition was to establish the lowest accident-severity rate, thus showing the smallest loss of time from accidents in proportion to total number of man-hours worked. The reports covered all lost-time accidents that occurred during the year, that is, all accidents that disabled an employee beyond the day or shift on which the accident occurred. Detailed information for each of the 59 coal mines is given in the appended table. Each mine employed at least fifty men underground; over half of than employed more than 200 men underground. Hence the accident records should be typical of those of large-scale mining operations in general where the company is devoting special attention to accident-prevention work. The mines covered by the reports are situated in eleven States: Alabama, Illinois, Indiana, Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Utah, Washington, and West Virginia.A tabulation of the reports covering the 59 mines showed an accident-frequency rate of 123 per million hours of ""exposure* and an accident-severity rate of 10.214 per thousand hours of exposure3. The total volume of exposure or employment was 29,117,561 hours, representing the equivalent of work of 12,000 men for three hundred 8-hour shifts. The records covered employment and accident above ground as well as underground, although they did not include stripping or open-pit mining. Accidents during the year resulted in 33 deaths, 1 permanent total disability, 28 permanent partial disabilities, and 3,510 temporary injuries. These accidents represented a loss of tine equal to 297,417 man days. In arriving at this lost-time equivalent, each fatality and permanent total disability was weighted at 6,000 lost days (see footnote 3), as specified in the scale adopted by the International Association of Industrial Accident Boards and Commissions; permanent partial disabilities were weighted according to nature of injury, in accordance with the scale adopted by the :Board; temporary injuries were weighted according to the actual number of calendar days during which the employee was incapacitated as a result of the injury."

Nov 1, 1926

By E. R. Palowitch, A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high - sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations . The survey , which provided information on Appalachian region coals only , indicated that such important coalbeds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14 - mesh top size . For many other coalbeds amenability to sulfur liberation by crushing was indicated , although too few samples were available to draw firm conclusions .

Jan 1, 1966

By J. R. Thoenen

Profits in the crushed-stone industry, as in any other, represent the difference between selling price and production cost. When consumer demand increases rapidly, as occurred in the crushed-stone industry from 1918 to 1927, selling prices tend to rise. Cost of production usually rises, also, owing to the expense of expanding facilities, searching for and developing new quarries, and purchasing, installing, and operating new equipment. Frequently, also, the inattention of managements to the details of operating costs is responsible for their increase. This is not due to negligence but rather to the necessity of confining attention to the problems involved in producing material to supply orders. When market conditions change and consumer demand becomes stabilized or contracts, the producer's attention usually is directed to assuring the orders necessary to keep his enlarged facilities busy. Hence, competition increases and soiling prices decline.

Jan 1, 1939

By R. V. Ramani, J. M. Mutmansky, P. C. Luna, V. A. Marple, Honglin He, B. A. Olson

The development of a sampling instrument for the assessment of an underground coal miner’s exposure to airborne respirable coal mine dust on a continuous and real-time basis has been long identified as essential for timely initiation of control actions. A respirable dust dosimeter (RDD) which operates on the principle of increasing pressure across a filter media with increasing dust mass on the filter has been developed by the National Institute for Occupational Safety and Health. Comparisons of the performance of the RDD with an U.S. approved gravimetric respirable dust sampler (GRD) have shown that the RDD may meet the requirements for measuring miners’ exposures on a cumulative, near real-time basis such as mid-shift and end of shift exposures. Recently, the performances of the RDD and GRD were compared by conducting side-by-side area sampling experiments in a controlled experimental environment in the laboratory and in underground coal mines under normal operating conditions. In this paper, the results from the in-mine study are presented and discussed. The experimental design for the in-mine study included two mines in different coal seams in different geographic coal regions. To ensure a wide range of concentrations, the experiments were conducted in a continuous miner section in Mine 1, and a longwall face in Mine 2. Airborne dust sampling was conducted for four different shifts at each mine. In each shift, two samples of different exposure durations were collected from two different locations. Each sample consisted of the readings of three dosimeters and the exposed filters from the three paired GRD samplers. As a result, a total of 96 comparative samples were obtained, 48 for each mine. The data were analyzed for the precision of the RDD and GRD measurements and for the relationships between the differential pressure of the RDD and the mass of dust on the paired GRD filter. The analyses indicate that, on the average, the RDD and the GRD track the airborne respirable dust concentrations well, exhibiting both a high correlation between the two measurements and a reliable predictive relationship of one from the other. Details of the experimental design, data analyses procedures, results, conclusions and recommendations of the underground experiments are presented in this paper.

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By E. W. Dean

A previous report of the Bureau of Mines* has supplied data for the physical and chemical properties of samples of crude petroleum produced in the eastern fields of the United States. It was issued as a preliminary chapter of a bulletin which is to cover the results of a survey of the entire country. The present report is a second preliminary chapter including figures that are available for the producing fields of the Rocky Mountain district. Work is being continued. with a series of samples from the States of Kansas and Oklahoma which will be described in a third preliminary chapter, to appear at a subsequent date. Acknowledgments. The obtaining of samples was rendered possible through the courtesy of representatives of a number of producing and refining companies operating in the Rocky Mountain district. The Bureau hereby acknowledges its appreciation of the hearty spirit of cooperation that was universally encountered.

Jan 1, 1921

By Arthur B. Johnson

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from four potash companies operating in the Permian Basin near Carlsbad, N. Mex. These ores, containing 13 to 22 percent K20 and 3 to 7 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high slime content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions and washing of the ore as opposed to strenuous attritioning. Bench-scale physical beneficiation techniques for recovering potash minerals and the development of ore-dressing systems by flotation resulted in obtaining acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 58.7 to 60.4 percent K20 with recoveries of 71.0 to 83.4 percent 0f the K20 values can be obtained.

Jan 1, 1971

By Helen E. Edwards

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy facilitating the theoretical study of flame and combustion phenomena. This report is the third of a series3/ presenting results of the study for particular fuel-oxidant systems. The equilibrium composition of the products of combustion and the adiabatic flame temperatures of specified oxyacetylene systems have been computed.

Jan 1, 1953

By Peter D. Lohn

The Bureau of Mines conducted both laboratory and field investigations to study the effectiveness of medium-pressure (up to 30,000 psi) water jets in controlling the generation of airborne respirable dust during the hydraulic fragmentation of coal. Laboratory studies were conducted at the Farmington High Energy Test Site of the Twin Cities Mining Research Center, and field studies were carried out at the Humphrey No. 7 mine, Mount Morris, Pa., in the Pittsburgh coalbed. The water jets were produced by commercially available triplex pumps. The dust samples were collected by midget impinger samplers, and analyzed by electronic and optical counting techniques. Respirable dust concentration for a full-scale production model was projected at below 2 mg/m3, the maximum exposure allowed by the Federal Coal Mine Health and Safety Act of 1969.

Jan 1, 1975

By H. B. Brunot

On April 26, 1949, the Bureau first approved a machine designed to replace the cycle of cutting, blasting, and loading coal by a single operation. This machine took the coal directly from the solid face and delivered it to transportation equipment. By January 1, 1955, 30 approvals for designs of machines of this type had been granted by the Bureau. In the main, this paper describes briefly the action of the various designs approved as permissible. In addition, the approval number, the date of approval, the voltage of the power supply, the number and character of the explosion-proof accessory parts, the size of the trailing cable, and the overcurrent protection at the outby end of the trailing cable are given for each design. Since no similar information has been published by the Bureau, it is hoped the material in this paper will be valuable in giving the mining public an organized look at the various machines of this nature that have been approved as permissible by the Bureau.

Jan 1, 1956

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By Howard F. Carl

"INTRODUCTION Talc is a hydrous magnesium silicate mineral found throughout the world in deposits of economic importance. This mineral occurs in different physical forms and varying degrees of purity, both of which affect its ultimate commercial usage. Talc is used in finely ground condition by the ceramic, paint, paper, rubber, cosmetic, and other industries. Most domestic talc production is of this type. Talc also occurs, although much less frequently, in massive, fine-grained, fairly homogeneous bodies; the impure varieties are the familiar soapstones, and the purer form is frequently called ""steatite."" Because of certain properties, the purest grades of this massive variety have a monetary value about 20 times that of the ground talc.One desirable property of this massive talc is its amenability to accurate cutttng, machining, and working in many ways, similar to a hard wood or soft metal, and then firing without warping or appreciable shrinkage into a hard, refractory ceramic body. Consequently, shapes that cannot be formed conveniently by molding and pressing can be produced readily with ordinary machine tools. When talc is fired to about 1,100° C., it is converted to a ceramic body with certain very desirable physical properties. This fired material has a hardness and toughness frequently superior to steel. It is a refractory and an exceptionally good electrical insulator. When formed from a high-grade talc essentially free from iron, it has unusually low dielectric losees, even at very high frequencies."

Feb 1, 1945

By Franklin D. Cooper

This Bureau of Mines study reviews current and proposed methods of extracting copper from sub-mill-grade ore by leaching. The amount of copper produced by hydrometallurgy has increased dramatically in recent years and will probably be about 200,000 tons per year by 1970.

Jan 1, 1968

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

In the interest of safety in mining, the Bureau of Mines recommends: 1. That cages or skips used for hoisting or lowering men in vertical and steeply inclined shafts shall be provided with safety catches designed to prevent falling of the cage or skip if the hoisting rope or other connections break; and 2. That cars used. for hoisting or lowering men with ropes in slopes shall be provided with arresting devices, other than ordinary brakes, that come into action if the hoisting rope or other connections break. In presenting this decision, it is recognized that the principal requirements for safety in hoisting operations are the use of hoisting ropes of ample size and strength to provide a factor of safety recognized as adequate by the best en engineering practice; their proper care, protection against undue wear and corrosion, and frequent inspection; and immediate removal of ropes from service when inspection or tests cast doubt upon their further safe serviceability.

Jan 1, 1938

By Paul B. Harder

Round Mountain Gold (RMG) in central Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By Mark Sheppard

This p aver is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different types of primary crushers; and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of the fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938