Search Documents

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

By K. O. Bennington

Cancrinite is one eonstituentof "red muds," a high-volume waste product of alumina production by the Bayer process. The Bureau of Mines determined the thermochemical properties of cancrinite as part of a program to provide such data for minerals of industrial importance. Cancrinite [Na7.68(A16Si6024)(N03)1.68 (H2O)4.1] was synthesized by reacting aluminum silicate gel with a solution of NaOH and NaN03, and the composition was determined by chemical analysis, differential scanning calorimetry, and thermogravimetric analysis. The heat of solution was determined by hydrofluoric acid solution calorimetry. The standard enthalpy of formation at 298.15 K, ?Hf°298, is ?Hf°298 = -3,487.97 ±2.6 kcal/mol, and the standard enthalpy of formation from the oxides and NaN03, ?H°298, is ?H°298 = -215.20 ±l.8 kcal/mol.

Jan 1, 1983

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964

By William I. Nissen, Richard Havens

Continuous flotation studies were made at a 50 - lb - per - hr feed rate to confirm the effectiveness of a batch - scale procedure for concentrating phenacite and bertrandite minerals from Mount Wheeler ores that contained , in percent , 0.47 , 0.78 , and 4.7 BeO . The procedure for selective froth flotation of the beryllium minerals from a gangue composed chiefly of calcite , fluorite , and mica comprised closely controlled preconditioning with sodium fluoride and sodium hexametaphosphate in a series of small mechanically agitated tanks and use of a mixture of oleic acid with kerosine , fuel oil , or turpentine as a collector . It was difficult to adapt the laboratory flotation procedure to continuous operation . The principal problem of achieving adequate conditioning to depress calcite and fluorite ultimately was resolved by conditioning in series . Thereafter , three ore samples of different grades treated on a continuous basis yielded concentrates containing from 12 to 25 percent Beo from these relatively complex and difficult ores . Recoveries , on a BeO basis , ranged from 75 to 88 percent . Losses , which primarily were due to incomplete liberation , probably could be lowered in a commercial operation .

Jan 1, 1964

By John S. Dunning

This paper is one of a series describing methods and costs of recovering sand and gravel from deposits in the United States and deals directly with the operations of the Atlas Sand, Gravel and Stone Co. at Farmington, Conn. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs might in some instances cause embarasement to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue.

Jan 1, 1933

By John R. Coulson

Each State and the Federal Government was surveyed for existing certification requirements, the industry yes surveyed for the needs for training blasters, and the training that was available. Recommendations for training and certification for blasters were made.

Jan 1, 1980

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By James F. Devine

The radial, vertical, and transverse components of particle velocity were recorded by Bureau of Mines investigators along gage arrays extending in one or two directions for 145 to 3,170 feet at five quarries. Of the 39 quarry blasts, 12 were instantaneous blasts, 5 were of the one hole per delay type, using millisecond delayed caps, and 22 were multiple hole per delay type employing millisecond delay detonating fuse connectors. Charge weight per hole ranged from 8 to 1,500 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 25 to 4,620 pounds.

Jan 1, 1966

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979

By M. R. Geer

Three coals from the Wilkes on - Carbonado district of Pierce County , Washington , were subjected to washability analyses to estimate the amount and quality of washed coal obtainable . Because the coals were unusually difficult to clean , the washability examinations were supplemented by table tests , tests in dense - medium cleaning units , and flotation tests . None of the coals could be reduced to the desired 10 percent ash by tabling and the response to flotation by two of them was poor . Dense -medium treatment provided coal of the desired quality , but with the most difficult coal the recovery efficiency was lower than usual .

Jan 1, 1964

By R. P. Beyer

[The Bureau of Mines has measured the low-temperature heat capacities and high-temperature enthalpies of crystalline K2Si2O5 as part of a program for advancing mineral resources technology with energy economy. High-temperature enthalpies of glassy and liquid K2Si2O5 and crystalline K2SiO3 were also mea¬sured. An adiabatic calorimeter operating over the range 5 to 308 K was used for the heat capacity measurements for K2Si2O5 from which the standard entropy at 298.15 K, S°298 = 45.55 ±0.05 cal/deg-mole, was calculated. Tabulated values of Cp°, S°, -(G° -HO°)/T, and H°-HO° from 5 to 300 K are given for K2Si2O5. A copper-block drop calorimeter was used in the enthalpy measurements, operating from 298.15 to 1,198 K for K2SiO3 and from 298.15 to 1,453.8 K for K2Si2O5. No transitions were found for K2SiO3. The KI2Si2O5 showed two reversible first order transitions, one at 510 K with a heat of transition of 0.29 kcal/mole and one at 867 K with a heat of transition of 0.38 kcal/mole. The heat of fusion for K2Si2O5 20 5 was calculated to be 8.42 kcal/mole. Relative enthalpies are given in equation form, and high-temperature values are tabulated for Cp°, S°, - (G°-H°298 )/T, and H°-H°298 . Also tabulated are ?H°, ?G°, and log K for formation of K2SiO3 and K2Si2O5 from both the elements and the oxides.]

Jan 1, 1979

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.

By Thomas A. Phillips

An economic evaluation of the Bureau of Mines process for the separation of raw urban refuse into its metal, mineral, and energy components is presented. The process recovers ferrous metal, mixed nonferrous metals, aluminum, mixed-color glass cullet, and refuse-derived fuel products from raw refuse. Data for this evaluation were obtained from selected runs at the Bureau's pilot plant in Edmonston, Md. A cost estimate was prepared for a plant capable of processing 1,000 tons per day of raw urban refuse operating two shifts, 6 days per week. The fixed capital cost, based on second quarter 1976 equipment costs, is approximately $14.5 million excluding land and shipping containers. The estimated operating cost is approximately $8 per ton of refuse processed. This does not include credit for the products, transportation of the products, a tipping fee, or a dumping fee for wastes produced. No finance charges or taxes are included in the operating costs.

Jan 1, 1977

By K. C. Dean

During investigation of the occurrence of manganese deposits in the western United States, examining engineers of the Bureau of Mines collected samples from several properties in Montana. Extensive laboratory tests were made to determine the amenability of these ores to standard ore-dressing methods of concentration to produce marketable-grade products. The Tzarena claim, one of the properties sampled, is on the western end of the Rama or Black Chief vein in the city of Butte, Silver Bow County, Mont., on the southwestern periphery of the mining district. The Black Chief 'WAR system contains one of the largest and most extensive known rhodochrosite deposits in the world. Test work was conducted on two samples of Tzarena ore. Sample 1 is representative of a vain 5 feet wide on the 150-foot level of the Tzarena shaft. Sample 2 is representative of a vein 8 feet wide in the 100-foot level of the shaft. The Minnie Jane mine, 1/2 mile northwest of the Tzarena claim, contains ore similar in mineralogical composition to Tzarena ore but differing materially in manganese content and to some extent in physical characteristics. Ore-dressing investigations were made on three samples of Minnie Jane ore. Sample 1 represented stock-piled ore, sample 2 represented ore from Minnie Jane mine having a considerable sulfide content, and sample 3 represented low-grade ore.

Jan 1, 1951

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By H. J. Heinen

To maximize productivity through improved minerals processing technology, the U.S. Department of the Interior, Bureau of Mines, is investigating particle agglomeration techniques as a means of increasing the percolation rates of leach solutions in heap leaching of clayey gold-silver ores. Simulated heap leach experiments were conducted on 50-pound charges of ore that were contained in 5.5-inch-diameter columns, 5 feet in height. Results indicated that the percolation rate of cyanide leach solution could be enhanced markedly by mixing the ore with controlled amounts of lime, flocculants, and water, and then aging the mixture prior to the column leach step. Experimental results obtained on 20-mesh silver tailings and gold ore crushed to 3/8 inch and to 1 inch showed that it was possible to increase percolation rates as much as 100-fold without sacrificing silver-gold extraction. Larger scale tests conducted in 24-inch-diameter, 16-foot-high columns closely paralleled bench-scale results. By improving percolation leaching, these techniques have the potential of helping to solve environmental problems associated with tailings disposal as well as making an important economic impact on gold-silver recovery operations. Investigations are continuing to develop binders superior to lime for particle agglomeration pretreatment.

Jan 1, 1979