Search Documents

By Mackenzie Burnett

The Brattice Window Method was used to measure the leakage rates of a total of 42 ventilation stoppings in 8 hardrock mines. Various types of stopping construction were evaluated. The following types are listed in order of decreasing effectiveness: 1) Cinder block, 2) Timber and mortar, 3) Timber and polyurethane foam, and 4) Timber and brattice material. There are slight differences in the effectiveness of the first three types, while the timber and brattice type is substantially inferior to the others. The repeatability of the Brattice Window Method was found to vary with physical conditions in the mine such as stopping location with respect to intersections, regularity of drift cross section, and the presence of hardware such as air and water pipes, timber sets and wire mesh. The Brattice Window Method is viewed primarily as a tool for estimating and comparing stopping leakages for the purpose of determining where repair efforts should be concentrated. A laboratory test program resulted in the derivation of several "rules of thumb" for employing the Brattice Window Method, which will aid in securing accurate and repeatable data.

Jan 1, 1979

By MINE SAFETY BOARD

RECOMMENDATIONS OF THE UNITED STATES BUREAU OF MINES ON CERTAIN QUESTIONS OF SAFETY AS OF FEBRUARY 3 , 1933

Jul 1, 1933

By Wadaw Cybulski

The problem of coal dust explosions: Basic information about the explicability of coal dust: Main parameters of the explosibility of coal dust; Main parameters of the explosibility of coal dust; Limit explosibility of coal dust and its dependence upon the basic parameters: The effect of the initiator of the explosion-on-the explosibility of coal dust: The dependence of the course of an explosion upon the distribution of coal dust in the workings, upon the dimensions of the workings, the length of zones, the direction of the development of explosions and upon the content of firedamp in the air of the workings; Con-sequences of coal dust explosions; The ways of suppressing the danger of coal dust explosions; Stopping the developed coal dust explosions; The explosibility and explosions of lignite dust of xylite structure

Jan 1, 1975

By Matthew N. Plis

This U.S. Bureau of Mines report presents the documentation for COALVAL, a coal property evaluation software package developed on Lotus 1-2-3,4 version 2.2, spreadsheets. The software is compatible with version 3.1 as well, and may provisionally be run on the earlier 2.01 version. COALVAL is a menu-driven program that produces a prefeasibility-level cost analysis of mine-planned coal resources. The package contains cost models for each of five coal mining methods commonly employed in Appalachia: auger, contour strip, mountain top removal, continuous miner, and longwall. Other models, such as a dragline cost model, will be incorporated as the Bureau's Coal Recoverability Program matures. COALVAL allows mine operators, evaluators, consultants, and Government entities to input resource data and the various production, operating, and cost variables that pertain to their property. The program can evaluate up to 25 seams, each to be mined with up to five different mining methods, within a given area. Summary spreadsheets listing the cost per clean ton to mine the resources, f.o.b. the tipple, are produced for each property, seam, and mining method/seam combination.

Jan 1, 1993

By Richard P. Cislo

The evaluation of the effectiveness of the time domain Coal Interface Detector developed by the General Electric Company under contract H0155120 is the subject of this report. The sensor utilizes differences in the time characteristics of shearer vibrations as sensed by an accelerometer mounted on the ranging arm to discriminate the cutting of coal and rock. Pour identical time domain sensors were supplied by the Bureau for field evaluation. The performance of the time domain sensor was evaluated by an extensive field test and data collection program that included four longwall mines and a total of nine mine visits. The intent was to determine the sensor's applicability to a wide range of mining conditions and to document its limitations. Results of the extensive field tests indicate that shearer vibration data processed by GE's time domain signal processing algorithm cannot be used to reliably detect when the cutting drum crossed the coal/rock interface.

Jan 1, 1987

This report covers the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. Significant conclusions that will be of benefit to the entire mining industry are the following: It appears from the study that the productivity of the slushing equipment itself cannot be substantially increased using the existing technology; the unsafe situations associated with slushers can be improved by better anchoring practices, by providing better work station layout that incorporates improved clearances and protected walkways over the ore pocket, by lighting the slusher drift, and by improved operator training; improved technology needs to be applied to the movement of broken ore in the stopes; and slushers will continue to be used in the mining industry in certain spedial and unique situations outlined in the report.

Jan 1, 1974

By M. E. Adam

This report describes the construction and testing of large (30 ft high by 55 ft wide) stopping and overcast structures in an oil shale mine. The work was undertaken to develop construction techniques and cost data, and to measure leakage rates on full scale structures in an oil shale mine. A design data base was developed by reviewing industry practice, oil shale industry plans, and technical literature. Alternate layouts for room and pillar mining were examined to find ways to reduce the size and number of ventilation control structures. Six full size stoppings and one overcast were built in the Colony Pilot Mine. Leakage rates were measured using both SF6 tracer gas techniques and the ?brattice window? method. The leakage was measured both before and after a full scale face blast. Blast air pressures were measured across two of the stoppings. Cost and leakage data were used to evaluate the projected overall performance of various combinations of the stoppings in a two-panel oil shale mine.

Jan 1, 1986

By Mark K. Larson

Researchers at the U.S. Bureau of Mines have developed a FORTRAN computer program that can calculate stress states from overcoring measurements obtained from hollow inclusion cells, triaxial cells, strain gauges installed on the wall of a bored raise, doorstopper gauges, borehole deformation gauges, or a combination of any of these gauges. Such stress states are calculated with reference to global and principal coordinate systems. The background of the development of the program, its capabilities, and its special features, as well as the input required, are described in this report. Sample output is also shown in appendix C. Difficulties associated with numerical calculations of principal stresses and directions are pointed out. Threshold values for detecting these problems are reported; these values may be changed by the user as desired. Several test problems were set up to verify the computer program and were successfully solved.

Jan 1, 1992

By E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916,1 and an investigation of Illinois coal-washing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coal. OBJECTS OF THE INVESTIGATION The present investigation was limited to a study of screening as applied in preparing mineral products with the expectation of obtaining more comprehensive information on screening machinery.

Jan 1, 1925

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By R. L. Soderberg

Large open stopes mined by vertical crater retreat or sublevel s are sometimes backfilled with uncemented sand to support the stope walls and alleviate rock bursts. The failure of bulkheads in two different mines prompted a research project at the Bureau of Mines to prevent a recurrence of these failures. A series of laboratory tests with drains and sand filters was conducted to measure the bulk-head pressures when adequate drainage was maintained. Results showed that bulkhead pressure was reduced to near zero while drains were in operation, as compared to full hydrostatic pressure when drains were blocked or drainage was restricted. A relatively simple, free-draining bulkhead was shown to be adequate.

Jan 1, 1985

By Robert G. Bottge

The Bureau of Mines has engaged m a program to determine the availability of land for mineral exploration and development in Alaska. Land availability, based on ownership and Federal and State laws and policies, is compared with mineral terranes and mineral deposits. This is the fifth of six regional studies, which cover the State with a comprehensive set of maps and data compilations. This study covers an area of 112.3 million acres in western Alaska. In July 1986, 41.0 million acres, 37% of the study area, were available for mineral exploration and development; 14.6 million acres, 13%, were available with restrictions; and 56.7 million acres, 50%, were unavailable. Nearly 65% of the unavailable land is classified as national parks, preserves, wildlife refuges, and wild and scenic rivers. Of the 34.0 million acres of mineral terranes that underlie the study area, 12.9 million acres, 38%, are available for exploration and development; 3.6 million acres, 11%, are available with restrictions; and 17.5 million acres, 51%, are unavailable.

Jan 1, 1988

By Charles L. Parsons

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign countries and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treatment of mineral resources, the Bureau of Mines undertook an investigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70,a which gave an outline of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publishing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treatment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930

By W. E. Young, D. T. Delicate

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Nov 1, 1963

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Ronald S. Conti

Historically, underground mine rescue teams have received training only in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fire drills every 90 days, this does not fully prepare them for the conditions that may be encountered in real escape situations, such as smoke filled entries. This paper describes technology and realistic training simulations that have been identified for the general workforce and mine emergency responders. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. These technological advancements can improve the state of readiness for rescue personnel and increase the chances of survival for personnel escaping from underground emergencies.

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation. and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice. making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being headed by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems best suited for the work in hand. The following, projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration or a linear relation between surface and coercive force in magnetic minerals and Its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1. 1934, to June 30, 1935.

Jan 1, 1936

By James M. Link

Underground coal mining is the most hazardous industrial occupation in the United States.. Haulage accidents in underground coal mines contribute substantially to the occupational hazards of this type of work. In an effort to improve mine safety, a completely hydraulic transport system has been designed to move coal from the mine face to the preparation plant. The capital investment for the hydraulic haulage system is great, and the size of the mine developed for this study is large. Mine production for the conventional haulage mine is 1. 1 million tons of clean coal per year, while the hydraulic haulage mine will produce over 1.6 million tons of clean coal per year. Safety statistics for a number of mines of this size are shown.

Jan 1, 1975