Search Documents

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971

By C. J. Chindgren, L. C. Bauerle, J. B. Rosenbaum

Modifications of the conventional method of preparing ductile vanadium metal by calcium reduction of V2 05 in a bomb were explored for clues to a more economical procedure . The modifications examined included ( 1 ) omitting the gas purge of the bomb ordinarily used for eliminating atmospheric nitrogen , (2 ) using low- grade vanadium feed materials , ( 3 ) using alternative reductants , such as aluminum , magnesium , and silicon , and reductant mixtures , and ( 4 ) bomb refining of aluminothermic metal produced in open- vessel reductions . The most promising modification appeared to be bomb refining , using calcium to purify vanadium metal -- of low aluminum but high oxygen content-- prepared by open- vessel aluminothermic reduction of vanadium pentoxide .

Jul 1, 1960

By Robert F. Stewart

The oxidation of structural materials at high temperatures in gas-cooled systems can be greatly retarded by the addition of small amounts of hydrogen to the inert coolant. In experimental equipment for gasifying coal with heat transferred by helium, the oxidation of graphite and metals (molybdenum, tungsten, and certain stainless steels) by trace impurities in the coolant helium was virtually eliminated by adding 0.1 to 1.0 percent hydrogen. The reaction of hydrogen with praphite does not preclude its use to retard oxidation; at 2,400° F. only 0.2 pound of graphite per square foot per year is lost for each percent of hydrogen in the helium. The addition of hydrogen appeared to prevent the mass transfer of carbon often associated with oxidation of graphite, without causing noticeable embrittlement of stainless steels and molybdenum or other damaging effects. This method has been tested in precision gas-recycle systems and applied successfully for more than a year in a pilot-scale unit operating at 250 pounds per square inch gage and 2,400° F. It is now used routinely and can be applied to many gas-cooled systems operating at high temperatures.

Jan 1, 1962

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

By Denise A. Herzog

The U.S. Bureau of Mines conducted a study of cyanide leach technology used in Alaska's mineral industry from 1987 through 1990. Literature and cost data were obtained for mines in the contiguous United States, Canada, and Alaska that use cyanide to recover gold and silver. The data was compiled in an effort to evaluate the economics and conditions associated with cyanide use in Alaska. This report discusses heap leaching methodology and evaluates a "typical" heap leach operation in Nevada and compares the results of the Nevada operation to an analogous hypothetical mine in Interior Alaska. Five daily tonnage rates were analyzed for both the Nevada and the Alaska operations to evaluate the spectrum of economic possibilities. The discounted cash flow rate of return (DCFROR) for each production rate was then evaluated in terms of recoverable metal value (RMV). The Nevada RMV for each production rate was then compared with its Alaskan counterpart, and the results averaged. The Alaskan production costs are an average of 1.71 times greater than costs associated with mining in Nevada at a 0% DCFROR. At 15% DCFROR, costs in Alaska are 2.01 times greater than those in Nevada. Costs are higher in Alaska because of the shorter leaching season, increased labor and transportation costs, and heavier precipitation and vegetation.

Jan 1, 1991

By D. Harrington

Although the explosion-fatality record for the fiscal year 1944 showed considerable improvement over those of the preceding 4 years, it is still fur from creditable, and the coal-mining industry and agencies interested in the prevention of coal-mine accidents should not be satisfied until accidents from explosions and fires are eliminated. In view of present knowledge of the methods of preventing explosions and fires, such disasters are inexcusable and discredit the mining industry. Despite this knowledge, far too many coal¬mine operators and employees continue to follow procedures that have resulted in disasters in the past. Included in the appendix to this circular are a number of safety measures designed to prevent coal-mine explosions and fires and metal-mine fires. Their adoption is essential if explosions and fires are to be prevented, as certainly they should be. An epidemic of disastrous mine fires of electrical origin during the past 2 years emphasizes the need for better methods of protection of underground electrical circuits. At present, committees of mining-electrical engineers, electrical-equipment manufacturers' representatives, and others are cooperating with the Bureau of Mines seeking means to solve this problem.

Jan 1, 1945

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By D. Harrington

"In at least three out of every four working faces in metal mines there is no attempt made to cause air circulation other than by use of compressed air, and in at least nine cases out of ten the compressed air is released merely by opening, or partly opening, the valve and allowing the compressed air to escape through open air hose used to convey the compressed air to the drilling machines. Usually no blowers are in use during periods of drilling, as the exhaust from the drill provides cool, comparatively fresh air for the driller; however, in some instances, the compressed-air line is provided with a tea connection, which permits taking air for the drill from one side of the tee, and air for ventilation through a separate hose used as a blower, simultaneously with drilling.Table 1 contains temperature and humidity data as to compressed-air blowers from open end of air hose at 36 working places in eleven metal mines of four States, embracing the mining of gold, silver, copper, lead and zinc ores, and at horizons ranging from 500 feet below the surface to as low as 4900 feet.It is noticed that the ordinary air surrounding the worker at the face gives an average wet bulb temperature of 81.7° F. for the 36 working faces, with 84.7° F. dry bulb and 87.2 per cent relative humidity. The average wet bulb tem¬perature of 36 readings at these working faces of compressed air at the end of the,hose as the air issues from the hose was 67.4° F., or 14.3 degrees lower than the average wet bulb readings of the air of the working places; however, the average dry bulb temperature of the 36 readings of compressed air as it issued from the end of the hose was 79.7° F., or only 5 degrees less than that of the general air (84.7°); the relative humidity was 51.1 per cent as against 87.2 per cent for the surrounding air. Readings were taken in five raises, seven crosscuts, ten drifts and 14 stopes.It will be noted that the velocity or movement of the general atmosphere at each of the entire 36 working faces, was found to be practically imperceptible; this might readily be inferred since compressed air is rarely used on blowers if there is adequate circulation of the general air of the place. Where rook temperatures could be obtained readily, they are shown; it is noticeable that the dry bulb temperature of the air of the working place varies little from the rock temperature, and that the dry bulb temperature of the compressed air as it issues from end of air hose varies only a few degrees from the temperature of the surrounding rock; in some instances the dry bulb temperature of the compressed air as it issued from the end of the air hose was higher than the rock temperature or the dry bulb temperature of the surrounding air."

May 1, 1921

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By Lloyd A. Morley

This report details the continuation of mine power systems transient research under USBM Grant G0155003. The purpose of the work, which commenced under Grant G0133077, is the elimination of safety hazards created by transients" and the objective is to provide knowledge about transients existing in a-c and d-c coal mine power systems. The report chapters cover theoretical background, instrumentation, and experimental investigations. The instrumentation discussion scans measurement problems and considerations plus the development of a low-cast peak-detector. Transient data from in-mine measurements are presented and include high-voltage distribution and d-c trolley systems. Extremely unique field exercises are described involving actual power equipment connected on the surface to duplicate typical underground coal mine system arrangements. Here, transients on high-voltage distribution resulting from vacuum circuit breaker operations could be observed under controlled conditions, and work centered around how surge capacitors effect transients. Using the in-mine and staged transient data, specific conclusions and recommendations are made with emphasis on high-voltage distribution.

Jan 1, 1977

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By L. D. Tracy

For many yeirs natural gas has been the principal fuel used in the he·1 ting furnaces in those mills located in the. Pi t-c;s. b.urgh district· \7hich manufacture bolts ., nuts, rivets, pick$, mattocks and srr.&11 for6ine;s. For a nUI.1"'.::>er of years the steady supply of this fuel has been more or less interrupted owing to the increased4and f·or d9mes tic use and to the increasing difficulty in securing an ad.eq_ua te c.1mount of natural gas. This condition has led a number of the steel compa.nies to substitute -oulvsrized coal a.s a fuel for the.furnaces. Elaborate irista.llations have been made for pulverizing tne coal ar!d _ coriveyi16 i -c to the fur:waces. • Soon after the furnaces ·-:commenced .. to operate ·,Vi th :pulverized coal, large quanti ties O::f.' fine dust beg.::in to accumulate on the platforms over the fu:rna. ces, the. roof trusses, on the outside of the va.rious· pip·e ·line electric cables a.i.1.d even on the roofs of the buildings. Some of tha comi:,a.n:;.0s, becomin·g alarmed, requested the Bureau of ;Unes to rr.c1ke an investigation to ascertcliin the.· licibili ty of this dust to cause an explosion.· Nhi le conducting this inves ti ga ti on,· an explosion· occurr-2! d in a.nothe:2 nill ·,7hich caused he death of one man and severely burned t;io others. Eleven sc1nrcles of the dust (which for convenience has been termed "mill d.ust 11 ) from various locations in the different mill' buildings were taken and submitted to chemical analyses, microscopic examination and also to flame and explosion tests. From the chu,1ica.l analyses it was found that· the volatile matter in th..:: dusts xanged -from 6.3 per cent to 23,54 per cent, fixed carbon from 50.88 per cent to 67.08 per cent and ash from 32.29 per cent to 32.16 per centw

Dec 1, 1919

By Charles M. McCulloch

This Bureau of Mines report discusses the principles of using computers to draw maps and plot geologic data of mining areas. The types of maps that can be drawn by a computer are reviewed, using as examples two separate areas where poor roof and gas emissions caused mining problems. Such maps can be used not only to help identify problem areas, but also to predict areas where problems could occur, thus giving mine operators time to work out solutions prior to mining. The average cost of a computer-drawn map for a mine property is less than $100, including computer time and man-hours for data preparation.

Jan 1, 1976

By R. V. Higgins

The, large volumes of low A. P. I. gravity oil that will remain in many shallow fields of California when such oils no longer can be recovered profitably by pumping are important potential sources of oil when ways and means are found to remove them from the reservoir sands. Estimated ultimate oil recoveries in many of the "low-gravity fields" of the San Joaquin Valley in California indicate that less than 25 percent (on the average) of the original oil will be recovered. These oils have viscosities of 1,000 or more centipoises at reservoir temperatures and, because of their high viscosity and low intensity of the reservoir pressure, the quantities that will be retained in the sands ultimately are so large and their recovery is such a challenge to petroleum engineers that the Bureau of Mines has made the study of their possible recovery one of its major projects. The fact that a slight increase of temperature materially reduces the viscosity of low A. P. I. gravity oils has 'prompted the use of various means for increasing the temperature of the oil in the reservoir sands and hence the rate of flow and Completeness of recovery of the oil. Hot oil, hot water, heated air, and natural gas, steam, super-heated steam, and the products of combustion have been circulated in wells to raise the temperature of the oil it the sands; electric heaters have been installed in wells, and butane and air have been intermittently exploded and the flames propagated through the tubing to the "pay" zones. None of the methods, however, have been entirely satisfactory for the recovery of large quantities of oil.

Jan 1, 1949

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe's are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC's of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By W. A. Stickney, J. W. Town

Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .

Jan 1, 1964

By Jack Wasserman, Don Wasserman, Gretchen Hinton, Logan Mullinix, Shekar Khanal

Human testing has always been a needed way to provide information on the effects of vehicle vibration, however, the manner of testing has not reflected the real situations of driver’s hands on a steering wheel and a seat with back support and driving tasks. The typical system have used a standard sinusoidal excitation rather than the typical types of road – truck excitations The new truck driver training simulators provide the combination of road roughness, speed effects, cab environment and individual tasks. The system has a full six axis simulation potential. The simulators have the protection of the individual by a combination of two ways for the individual to stop the motion as well as an operator with visual capability who can stop the testing. The closed simulator, shown in Figure 1, has the potential for providing motion during the operation.

Jan 6, 2006

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932