Search Documents

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By C. H. Schack, A. O. Ipsen, H. G. Poole

"INTRODUCTION In the course of the investigation of manganese mineral occurrences in continental United States, the Bureau of Mines has collected several lots of ore from properties in the vicinity of Long Valley, Ariz. The ore occurs as irregular and random pockets in a brecciated zone. As only high-grade portions of the deposits obtained by selective mining would be acceptable as commercial-grade manganese ores, an investigation was made to determine amenability of the ores to concentration by ore-dressing methods. Several types of ores, differing in grade and mineral associations, were studied.Ores from the Vaiazza property are of special interest, owing to the successful application of silica flotation for their concentration. Ores from the Shroup and Conner-Hough properties are very similar but differ somewhat in their response to ore-dressing Method's. In all instances, the man¬ganese minerals are psilomelane and pyrolusite, with minor amounts of other manganese oxides. The country rook is a brecciated limestone; the diluent in the high-grade ore pockets is chiefly silica. The low-grade manganese ores are limestone replacements, and the chief gangue material, of course, is limestone."

Nov 1, 1947

By F. E. Cash

The Holmes Safety Association was organized and named in honor of the late Dr. Joseph A. Holmes, first director of the United States Bureau of Mines. The association is a national organization and operates through local, sectional, or State chapters in mining, petroleum, and allied industries. The National Council of the Holmes Safety Association consists of representatives of State councils and local chapters, with the Director of the Bureau of Mines as president.

Jan 1, 1929

By T. F. Mitchell, Walter J. Long

"SUMMARYThis report is one of a series giving results of laboratory and pilot-plant investigations of the concentration of western manganese ores begun in December 1940. Data given summarize results of laboratory investigation of three samples of complex oxide manganese ores from the Madeline property, Lake View, and Victory claims, Clallam County (Olympic Peninsula), Wash. The samples represented an extremely intimate and complex association of manga¬nese oxide minerals with silica and iron.Owing to the complex nature of the ores, no effective concentration by ore-dressing methods was possible. No high-grade manganese concentrates were produced and the highest recovery at minimum accountable grade was only 55 percent on one of the ores tested.Since the Clallem County ores did not respond to ore-dressing methods, leaching processes were investigated, results of which are to be published in a separate report.INTRODUCTIONOre-beneficiation tests were conducted on three samples of manganese oxide ere from the Madeline, Lakeview, and Victory claims, Clallam County, Wash. The ores are extremely complex because of the unusually small size of manganese mineral particles, their mode of occurrence, and relationship to the gangue. None of the three ores was amenable to the production of high-grade manganese products by ore-dressing methods."

Dec 1, 1945

Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress -appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions end hearings2/ relative to the need for the survey, the opinion was expressed that crude oil held is storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to

Jan 1, 1938

By W. M. Deaton

The Keyes Helium Plant of the Federal Bureau of Mines was constructed under an expedited schedule, to supply the urgent and growing demand for helium in atomic energy, missiles, aerology, space exploration, shielded-arc welding, and low-temperature research. Construction began in December 1958 and ended in August 1959. The plant, near Keyes, Okla., processes 2 percent helium-bearing natural gas from the Keyes gasfield. In 1960 the plant produced and shipped 263 million cubic feet of helium (equivalent to an annual rate of 290 million cubic feet). Production cost was $9.11 a thousand cubic feet of helium. A low-temperature process involving two steps is used; the first separates a crude-helium product from the natural gas at about -250° F. and 225 pounds per square inch gage (p.s.i.g.); and the second purifies the crude helium to a high-purity product (Grade-A helium, 99.995 percent helium) at about -320° F. and 2,750 p.s.i.g.

Jan 1, 1961

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By M. M. Fine

Small-scale laboratory mineral-dressing studies were made on a total of nine individual or composite samples of manganese-bearing material from the west-central Arkansas, or Mena, district. Of these, only three yielded concentrates that would probably be acceptable for purchases by the Federal Government fur the National Stockpile. Concentrates from some of the other properties, however, contained more than 40 percent Mn and might be merchantable to other purchasers of manganese ore. In most instances, a too-intimate association of manganese oxides and gangue is conducive to low grade, low recovery, or both, so that mechanical concentration processes do not promise much for this district.

Jan 1, 1956

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Butler County, Pa. It is one of a series planned to determine which coals are suitable for producing metallurgical coke, either as mined or after beneficiation. More than 2 million tons of coal was produced in Butler County in 1958, of which about 25 percent was cleaned mechanically in four cleaning plants. Updating the 1942 coal-reserve estimates made by Ashley to December 31, 1958, more than 1,266 million tons of recoverable coal reserves remain in the county in beds that arc 24 inches or more thick. The Upper and Lower Freeport, Upper, Middle, and Lower Kittanning, Clarion, and Brookville beds were selected on the basis of production and estimated minable reserves. Sample locations were chosen after a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Four samples each were collected from the Upper Freeport and Middle Kittanning beds, three samples from the Brookville bed, two, samples from the Upper Kittanning bed, and one sample each from the Lower Freeport, Lower Kittanning, and Clarion beds.

Jan 1, 1960

By McHenry Mosier

This paper describes come mechanical raid electrical signal systems in common use in Metal-mine shafts, together with several distinctive systems that indicate or control the origin of the signal. The latter systems remove the hazard of the movement of the cage from one level in response to signals from another. Previous publications of the Bureau of Mines have covered several meritorious installations One of the best signal systems for deep shafts is at the Homestake mine4/. A successful installation of an induction system in the Lake Superior mining region permits signaling as well as telephoning from cages at rest or in motion5/. El Potosi mine uses a variation of the three-wire electric system6/. A mine in Utah has developed a system of the double trolly-wire type, in which the cage attendant may signal from a moving cage7/. At present no system of the sine-shaft signaling employing radio is available.

Jan 1, 1939

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By J. C. Fowler

The field testing of the Seismic Mine Monitor System is described. This system consists of nine geophones buried about 40 feet deep over a ten-square-mile area, the amplifiers and electronics needed to get the signals to the mine office, and a central processor unit to detect and locate explosions and large roof falls. Since the problems associated with the original installation were solved, this system has worked for 2 1/2 months. The system has detected roof falls in the pillar areas and has located blasts as small as 114 pound of dynamite. The location accuracy has, in general, been within 250 feet. The system is now being used to gather long-term data on the seismic activity of the mine.

Jan 1, 1974

To provide a simple means for rapidly checking methane concentrations at working faces in coal mines while remaining under permanently supported roof. The Approach: A light telescopic probe, through which a gas sample can be pumped Into a methanometer, has been developed. See Figure 1 [ ] How It Works: The telescopic probe consists of sections of small stainless steel tubing encased in sections of lightweight fiberglass tubing. When fully extended the probe is almost 19 ft. long; fully closed it is approximately 5-1/2 feet long. It can be used In either of these positions as well as at intermediate extensions. An approved methanometer is clamped to the probe by a support bracket.

Jan 1, 1975

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Colombia has been prepared from the best available information in Washington, but is released subject to correction and amplification; if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW Minerals in Colombia belong to the owner of the soil unless otherwise provided in the law. The following lands and deposits, however, are described as fiscal property of the State: Class 1. The public lands, mines, and salines which belong to the individual States (now Departments) prier to the adoption of the present constitution (1886).

Jan 1, 1929

By C. H. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen content of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By J. D. Sargent

Selenium might be described as a paradoxical element, being either a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden, The ordinary stable form of selenium is a crystalline, grayish solid with semi-metallic luster. It melts at 217° C., boils at 684.8° C., and has a density of 4.79.

Jan 1, 1955

By J. A. Ruppert, P. M. Sullivan

A process was developed on a laboratory scale in which iron contained in galvanizers ' zinc dross and aluminum contained in scrap zinc die - cast alloy were removed simultaneously . Melting both types of scrap together in the proper proportions resulted in formation of solid intermetallic Fe₂ Alg , which was readily removed from the melt by filtration and centrifugation . Recovery was 87 to 92 percent of the available zinc . Refined filtrate contained 0.02 percent iron and 0.20 percent aluminum. Aluminum content was further reduced to less than 0.01 percent by fluxing with zinc chloride . Low temperatures employed and inexpensive equipment requirements make the process commercially attractive .

Jan 1, 1964

By Donald P. Schlick

The Federal Coal Mine Health and Safety Act of 1969 requires each mine operator to implement the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare. This program requires frequent sampling of "high-risk" face workers and periodic sampling of other underground workers. Dust samples are collected by the coal mine operator and weighed at the Bureau's Pittsburgh Field Health Group, and the results are processed by the Bureau's Automatic Data Processing Section located in Denver, Colo. This paper presents the system employed by the Bureau to weigh the dust samples and to process and store the data.

Jan 1, 1971