Search Documents

By Cavallaro. J. A.

This report presents the results of a washability study of 455 raw coal channel samples with special emphasis on sulfur reduction. These raw coals contained on the average 14.0 percent ash, 1.91 percent pyritic sulfur, and 3.02 percent total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds. Finally a similar statistical evaluation is included showing composited data interpolated at Btu recovery levels of 50, 60, 70, 80, 90, and 100 percent. Graphical summations are presented for the various coal producing regions. Generally, significant sulfur reduction is achieved if the coals are crushed to a finer size and the higher specific gravity increments are removed. If a 50-percent Btu recovery was acceptable, then 32 percent of the samples tested could be upgraded to meet the current Environmental Protection Agency (EPA) standard of 1.2 pounds of S02 emission per million (MM) Btu when crushed to 14-mesh top size and separated gravimetrically.

Jan 1, 1976

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By Wing G. Agnew

The drilling and bit-sharpening practice in the southwest Wisconsin zinc district generally conforms to the procedure described herein, except at very small properties, where drill steel is sharpened by hand. Though hot milling of rock-drill bits is practiced in South Africa on some of the large-scale operations, it is seldom seen at American minus in any form. Because of the simplicity and low cost of the equipment, it was thought that a brief description might prove interesting to same of the operators in ether districts who do not have enough steel to sharpen to warrant equipping an elaborate sharpening shop.

Jan 1, 1936

By R. V. Higgins

A numerical method is presented to calculate the isopressure (isobar) lines and streamlines for an oilfield from the pressure distribution. A knowledge of these lines is useful in the study of the flow of fluids in underground reservoirs, especially for those containing gaseous and/or liquid hydrocarbons. This work was done primarily to enable determination of the shape factors needed in the calculation of petroleum reservoir performance. However, it has application for the flow of water in aquifers, or electricity or heat in odd-shaped geometry. Techniques previously developed were used to calculate the pressure distribution. From this pressure distribution, the isopressure lines were calculated accurately by the method presented in this paper. Then by successively projecting orthogonal lines from one isopressure line to another, the streamlines are determined. From the coordinates of the isopressures and the streamlines, the shape factors can then be determined by a published method. Computer methods are presented to calculate the streamlines and isopressures for any well-spacing pattern existing within a field with multiple wells. The method reproduces the flow net for several well configurations having extensive geometrical variations. Such information provides the petroleum engineer with data from which he can compute oil recoveries for different patterns and thereby maximize the recovery of hydrocarbons from the reservoir.

Jan 1, 1972

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By Raymond L. Lowrie

For many years it has been considered that an average of 50 percent of the coal in the deposits exploited has been recovered. Owing to many changes in mining methods during the past two decades, this study was initiated to obtain an up-to-date measurement of recovery percentage and thus establish part of the basis from which presently recoverable reserves may be estimated. Recovery percentages were determined within mined areas of 200 underground coal mines. These comprised a statistical sample selected to be representative of operating mines in relation to their significance to depletion of reserves. The results ranged from 29 to 91 percent and averaged 57.0 ± 1.7 percent (95-percent confidence limit). Six factors were identified mathematically as significantly affecting recovery percentages: (1) Pillaring system, (2) top rock and conditions, (3) bottom rock and conditions, (4) marketability, (5) coalbed thickness, and (6) productivity. Skill and attitude of mine operators toward recovery, although not measured, were probable factors. Five other variables that were tested did not show any significant relationship with recovery percentages. Also, five mining equipment features were identified, through discussions with mine officials, as affecting adversely recovery percentage at some mines.

Jan 1, 1968

By Lloyd A. Morley

Two mine electrical power system simulations are presented. The first is a batch processed procedure capable of modeling a single mining machine consisting of a number of motors operating under various loads. These loads are the mechanical torque loads present at the motor shaft. The second simulation is a more flexible tool for modeling entire mine electrical power systems~ Detailed analyses of bus voltages, transmission-line power flows, and machine behavior are possible. This simulation operates interactively and the power system is configured as the user responds to program generated questions and requests. Development of the theory behind the programming, as well as detailed explanations of the models, is presented. Examples are provided to demonstrate simulation capabilities.

Jan 1, 1978

By James S. Browning, W. H. Eddy

Laboratory batch and small - scale continuous flotation tests were conducted on a ferruginous barite - fluorspar ore from near Sweetwater , Tenn . , to determine the feasibility of producing commercial - grade fluorspar and barite concentrates . The lignin sulfonate - sodium fluoride - fatty acid method of floating fluorspar produced acid - grade concentrates . Flotation of the barite from the fluorspar tailing using petroleum sulfonate yielded concentrates suitable for use as a weighting agent in oil -well drilling muds . The continuous flotation tests , treating about 150 pounds of ore per hour , yielded fluorspar concentrates that assayed 98.3 percent CaF2 and barite concentrates that assayed 91.2 percent BaSO4 . The recovery of the two minerals was 91.2 and 85.2 percent , respectively .

Jan 1, 1964

By J. A. Cavallaro

To determine whether magnetite consumption could be reduced and salable coal production increased by using froth flotation units in series with magnetic separators, the Bureau of Mines conducted laboratory froth flotation tests on primary magnetic separator effluents obtained from three coal preparation plants. Tests were performed in a standard 500-gram-capacity laboratory batch flotation cell. Oleic acid and methylisobutyl carbinol were used as the collector and frother, respectively. Magnetite recovery was comparable to that expected from secondary magnetic separation, and salable float coal recoveries of 0,8 to 7.6 tons per hour were obtainable. The economics of the proposed technique appear to be sound.

Jan 1, 1966

By M. M. Wong

A brief investigation was made to determine the feasibility of electro-refining beryllium in a KCI-LiCI-BeC12 bath. Thin, platelike crystals of beryllium metal were produced by electrolyzing technical-grade beryllium metal beads (about 94-percent purity) as the soluble anode. Operating cell conditions were: Temperatures of 450° to 600° C.; an inert atmosphere; bath compositions of (1) 38.1 mol. percent KC1, 54.8 mol. percent LiCl, and 7.1 mol. percent BeC12 and (2) 36.7 mol. percent KC1, 52.7 mol. percent LiCl, and 10.6 mol. percent BeC12; cell voltages of 0.30 to 0.80; and initial cathode current densities of 50 to 435 a./sq, ft. Current efficiencies ranging from 87 to 96 percent were obtained. Qualitative spectrographic analyses of the metal products indicated that impurities were reduced. This technique offers the possibility of producing a grade of beryllium purer than that now generally available, which may have better mechanical properties.

Jan 1, 1960

By M. D. Carver

The purpose of this investigation was to determine the effects of variations in content (near the residual level) of the impurities aluminum, nitrogen, manganese, and copper on the corrosion rate in pressurized hot water and in pressurized steam of zircaloy-3, a zirconium-base alloy of 0.25 percent tin and 0.25 percent iron. Thirty-five 10-pound ingots were cast with the appropriate additions of impurity elements, and these were converted to wrought sheets. These specimens were then tested both in water and in steam. The analysis of the resulting data showed that in environments of either pressurized hot water or superheated steam, corrosion rates increased with increasing content of aluminum, nitrogen, or manganese, but were not affected by variations of copper. The effects of aluminum and nitrogen were found to be greater than the effect of manganese. INTRODUCTION At the request of the Atomic Energy Commission (AEC) in August 1956, the Federal Bureau of Mines, in cooperation with Bettis Plant of Westinghouse Electric Corp., began investigating the effects of certain impurity elements on the corrosion rates of zircaloy-3 in pressurized hot water and in pressurized steam. It was necessary to know these effects in order to set control limits on residual impurity levels in zirnaloy-3, intended for heat transfer service in the nuclear reactor of the pressurized water type. A factorial expert it was designed by Westinghouse statisticians. The Atomic Energy Commission provided raw zirconium sponge purchased from Wah Chang Corp. The Bureau's laboratory at Albany, Oreg., made material of different combinations of impurity levels and subjected the material to corrosion tests. This report will describe the work done at the Bureau laboratory and will show, quantitatively the effects of different residual levels of aluminum or nitrogen, or manganese or copper on corrosion rates.

Jan 1, 1961

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By Masami Hayashi

The Bureau of Mines estimated the cost for ,3 uranium ion-exchange recovery system using five grades of 17.0, leach solution producing 815,570 pounds of U 0? per year from an ammonium bicarbonate in situ leach solution. The system flowsheet consisted of four unit operations: (1) Multiple-compartment ion-exchange (MCIX) absorption; (2) MCIX elution; (3) precipitation of the uranium as yellow cake, filtering, calcining, and packaging; and (4) waste disposal. The total fixed capital cost of a system treating 2,000 gallons per minute of 0.1-gram-per-liter-U308 leach solution was estimated as $6,888,000. For n basic case of an MCIX system depreciating in 9 years, unit production cost of U308 was $3.51 per pound. A decrease in feed solution grade from 0.[4] to 0.03 gram per liter increased the production cost exponentially. Shorter depreciating periods significantly increased the production cost particularly for the lower grade feed solutions.

Jan 1, 1979

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By Philip E. Sanker

The Bureau of Mines conducted small-scale batch and semicontinuous tests on the reduction of zinc sulfide with iron according to the reaction ZnS + Fe ? FeS + Zn to determine reaction kinetics in the temperature range 1,000° to 1,400° C and to investigate the potential use of a scrap iron reductant. Batch tests indicated that a temperature of at least 1,300° C with a 1:1 mole ratio of Fe to ZnS is needed for good zinc recovery. Semicontinuous tests were conducted, using four zinc concentrate samples, containing various percentages of copper, cadmium, and lead, which were reacted with iron and iron contaminated with iron oxide and tin in an externally heated graphite furnace. Analysis of the zinc metal and FeS matte reaction products showed cadmium to be entirely in the zinc metal, copper to be in the FeS matte, and lead to be about 60 pct in the zinc metal and 40 pct in the matte. Tin reported to the matte, and none was detected above the O.OS-pct level in the zinc. Sulfur dioxide was not detected in the offgas when up to 20 pct of the iron was replaced by Fe203.

Jan 1, 1976

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By D. E. Kirby

The electrochemical reduction of AlC13 was investigated as a process for the production of aluminum. An externally heated, single-compartment cell with a rammed refractory lining was used with molten KCl-NaCl-AlC13 electrolyte. Aluminum was deposited qt 700° to 760° C with a current of 100 to 200 amperes on a molten aluminum cathode. Chlorine was evolved at a graphite anode and collected and measured to provide a quantitative evaluation of the AlC13 reduction. Aluminum was removed from the cell by siphoning or ladling. Granular AlC13 was added periodically to replenish that depleted from the electrolyte. Concentrations of 7.5 to 17.5 percent AlC13 in the electrolyte were optimum for operation. Anode current efficiencies of 83 to 85 percent were attained, using anode current densities of 5.9 amperes per square inch and an anode-cathode distance of 4 inches. The chemically bonded, alumina liner was resistant to attack by aluminum and chlorine but susceptible to erosion at the surface of the electrolyte. Titanium diboride proved suitable for the electrical connection to the molten aluminum cathode. Aluminum of a purity equal to or better than 1100 series metal was electrowon continuously from commercial AlC13 for a period of 4-1/2 months.

Jan 1, 1970

By R. Stefanko

This study concerns itself with the effects of diesel exhaust on mine ventilation systems. The approach here consisted of the development of mathematical models for emissions, dilution, and dispersion of gaseous pollutants from diesels. The general scheme was to use partial differential equations to predict concentration growths. Specifically, the following situations were modeled: 1. A single stationary diesel engine working in a single roadway. 2. A single diesel engine moving with uniform velocity in a single roadway. 3. Multiple diesel engines moving continuously in a cycle in a roadway with appreciable leakage. 4 Multiple diesel engines moving continuously in a cycle in a roadway with little or no leakage. 5. Multiple diesel engines moving randomly in a roadway with uniform air velocity.

Jan 1, 1974

By R. J. Leary

Significant improvements in surface conditions or mechanical properties of steels have been attributed by several investigators to ladle additions of small quantities of rare-earth metals or their oxides. To investigate systematically these effects in wrought and in cast plain carbon and alloy mechanical steels containing approximately 0.35 percent carbon, heats of four representative compositions were melted by the Bureau of Mines in a 4-ton open-hearth furnace. Each heat was cast into three sets of ingots to exemplify respectively, treatments with (1) rare-earth metals, (2) rare-earth metal oxides, and (3) an untreated set as a control. The development of melting, casting and rolling practices is described and discussed. Lance injection of oxygen shortly after melt raised the temperature of the metal immediately as much as 500° F., principally because mechanical agitation exposed the high-carbon metal to the flame and furnace root. An exceptional degree of superheat in the metal at the termination of the refining period was attributed to oxygen injection during the refining period. Bath temperatures higher than industrial practice were permitted by the all-basic furnace lining. Rates of carbon elimination as high as 0.036 percent carbon per minute were achieved by oxygen injections.

Jan 1, 1961