Search Documents

By Travis Rhoden

Merriam Webster?s Collegiate Dictio­nary (1996) defines team as ?a number of persons associated together in work or activity? and teamwork as ?work done by several associates with each doing a part, but all subordinating personal prominence to the efficiency of the whole? (page 1209). According to Dr. Geller, author of Building Successful Safety Teams: Together Everyone Achieves More (1998), a team of people working together for industrial safety consists of as few as two people or as many as fifteen who have complementary skills, assignments, or abilities for completing a particular task. Effective teams have members who share a common mission and relevant goals, and they share specific methods to reach their goals and accomplish their mission. They also have an evaluation system in place for holding themselves mutually accountable for goal-directed responsibilities.

Nov 1, 1998

By Roy Greenfield

Estimates are given for the distance from a seismometer at which a miner can probably be detected. The procedure in making these estimates was to first establish the natural noise levels at the output of a surface seismometer for the 25 to 100 Hz frequency passband. The noise levels give the range of values which may be expected in areas with no man-made noise. For each noise level, we give the detection threshold which, when exceeded, indicates that a signal has been received. Based on the signals recorded by Westinghouse, curves are given which show the peak signal amplitude as a function of source- to-receiver distance (slant range). Curves are given for the Westinghouse seismic thumper, a 50-pound timber, and a sledge. For a given type of source, the receive signal strength depends more strongly on slant range than on any other factor. However, there is approximately a five-to-one scatter in the amplitudes. Thus, further study of factors affecting the signal amplitude might allow better estimates to be made for any particular geological setting. Combining the signal amplitude with the detection thresholds for the different noise conditions gives the distances at which a miner should be detected. These are given in Table l* below. [ ] The text also gives the increase in detection ranges which should occur if steps are taken to increase S/N by 10 dB. We feel that 10 dB is a conservative estimate of the improvement possible. During an actual rescue operation, the seismic crew and system should be capable of making on-site estimates of their detection capability, based on measurements of the site noise, and upon the best available estimates of the

Jan 1, 1974

By P. H. Floyd

This report presents the results of laboratory and continuous mill-beneficiation tests conducted at the Bureau of Mines Northwest Electra Development laboratory, Albany, Oreg., on nonsulfide lead ore from the Sherman mine, Leland district, near Burke, Idaho. The predominant lead-bearing mineral in the ore sample treated was pyromorphite, a minor ore mineral of lead. Known reserves of pyromorphite lead ore in the United States are limited, although an appreciable tonnage of this type of ore is found in the Sherman mine. Very little pyromorphite is being mined in this mine or in the United States. This beneficiation problem presented a unique opportunity to study the mineral-dressing properties of a less widely known lead mineral, and consequently adds valuable knowledge to the ways of beneficiating ores containing nonsulfide lead values. This mineral-dressing problem was successful with conventional concentration methods of flotation and Gravity separation.

Jan 1, 1952

By I. L. Nichols

Volatilization of cesium from pollucite ore was investigated as an initial step in the production of purified cesium metal or cesium salts. High recovery of cesium and rubidium as chloride sublimates was accomplished by 2-hour roasts in a tube furnace using charges containing 1 part ore, 2 parts limestone, and 0.23 part calcium chloride. Recoveries of cesium in the sublimate product were 89.1, 92.9, and 95.2 pct, respectively, using 1,100° C and vacuum, 1,250° C with an air sweep, and 1,250° C without an air sweep. Most of the lithium, sodium, and potassium sublimed with the cesium and rubidium, but virtually none of the calcium, aluminum, and silicon in the charges was volatilized.

Jan 1, 1966

By R. V. Higgins

This report presents the results of a study of water injection in the HX sub-pool fault block V-B, in the Upper Terminal zone, Wilmington field, California, and is based on data obtained to May 1957. An earlier report3/ describes the results of gas injection in part of the field. The principal purpose of the pilot flood was to determine whether a sand having a permeability of 1,200 millidarcys and containing oil having a viscosity of 17 centipoises could be waterflooded effectively. The results of a preliminary study by engineers of the Long Beach Harbor Department of oil recoveries from areas where encroaching edgewater was active and the results of an independent study by a consultant retained by the Long Beach Harbor Department were favorable to a trial waterflood. After these preliminary studies, a detailed petroleum-engineering exam-ination was made of the technical details. As a result, a peripheral flood was started in June 1953. The peripheral flood was deemed desirable because the producing wells are bottomed a short distance from the edgewater. The HX subpool was selected for the pilot test because it is an isolated section of the Upper Terminal zone and is separated from the adjoining pools by faults on the east and west and by edgewater on the north, south, and west. Several petroleum-engineering methods were applied to evaluate the performance of the waterflood, and all showed that injecting water stimulated oil production.

Jan 1, 1958

By Robert E. Wood

[The temperature dependency of the low-density thermal conductivity coefficients, ?°T, of nitrogen, 100° to 1,200° K, is correlated with the Keyes' equation, ?T ½ -1 -12/T) WT = aT+ bT 10 The equation ?T,P = ?°T +a[ ]ß represented 509 experimental higher V pressure thermal conductivities in the temperature range 131.2° to 973.15° K for pressures to 500 atmospheres, with a mean absolute deviation of 2.35 percent. This equation was used to compute thermal conductivities of gaseous nitrogen for 47 pressures, 1 to 240 atmospheres, and 110 temperatures, 133° to 740° K, which are common to conditions encountered in Bureau of Mines helium purification processes. Isobaric heat capacities, CP, and viscosities, ?T,P, from previous work were combined with the present thermal conductivities, ?T,P, to compute Prandl1 numbers, C?T P / ?T ,P, of nitrogen. Tabular values of Prandtl num¬bers are presented for 49 pressures, 1 to 240 atmospheres, and 75 temperatures, 133° to 740° K. Estimated uncertainties are ±5 percent in the tabulated thermal conductivities and ±15 percent for the computed Prandtl numbers. However, the uncertainty may rise to ±10 percent for thermal conductivities and to ±30 percent for Prandtl numbers as the critical conditions of nitrogen are approached.]

Jan 1, 1971

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

By A. W. Kbair, L. D. Gehl

"INTRODUCTION The rock-bit interaction during the cutting process in underground mines has been a matter of great concern to mining operators, researchers and manufacturers, particularly after the passage of strict environmental laws. Coal cutting bears directly on airborne coal dust generation and rock cutting generates frictional sparks which may cause face ignitions, jeopardizing the productivity, safety and economy of the industry. It is imperative to investigate into the factors which have influence on bit we.ar. Hurt and Evans (1981) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits, and also worn bits were more responsible for ignition than the new bits. The results of a study (Khair et al., 1992) suggested that after 7% weight loss, the bit should be replaced. The polycrystalline compact diamond (PDC) tipped bits are reported to be cost effective in a study done by USBM (Twin Cities Research Center), and it was stated that the PDC tipped drill bits had 80 to 100 times longer life than the ordinary tungsten carbide (WC) tipped bits.This paper presents the results of the experiments which were conducted utilizing a coal cutting simulator at the laboratory of the Department of Mining Engineering, West Virginia University, USA. The description of the machine and the experimental set-up have been described elsewhere (Khair et al., 1989; Gehi & Khair, 1994), and therefore, will not be discussed here. The rock types which were used in experimen~ are Tennessee sandstone, Berea sandstone and Indiana limestone. The operating parameters include (1) drum speed, (2) water spray pressure and (3) bit type. Besides studying the wear characteristics influenced by the above mentioned variables, the effect of these parameters on the required cutting force, specific energy consumption, acoustic emissions rate and rise in temperature of the bit were also studied. A preliminary study was also done to compare we.ar characteristics of the WC bits with those of the poly-crystalline compact diamond tipped bits."

Dec 1, 1995

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By A. J. Hudson, M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

By D. R. Babich, E. R. Bauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of equipment sound levels and worker noise exposures in the stone/aggregate mining industry. Six stone/aggregate mines (three surface and three underground) were recently surveyed, and the findings (ire presented here. The surveys consisted of sound-level measurements conducted around various equipment and machinery (including stone processing and crushing equipment) and full-shift dose measurements to determine worker noise exposures. The findings identify the equipment and machinery that are likely to cause worker overexposures and identify the workers found to he experiencing overexposures. In addition, the benefit of cabs in reducing mobile equipment operator noise exposure is discussed.

By L. R. Burdick, J. F. Barkley

"There is a general conceit in the coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and surely from the same mine,is substantially a constant; that calculation of the moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or seam; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.To illustrate with a simple example;"

Jun 1, 1941

By G. B. Botsford

In August 1943 the Bureau of Mines began an investigation of the West Portal magnetite mines, which comprise the Swayze and Turkey Hill properties. The work included (1) traversing with a dip needle to record magnetic anomalies, (2) diamond drilling, and (3) sampling old mine dumps; it was completed in April 1944. The deposit consists of two parallel veins, which strike northeast and dip southeast. They carry magnetite in gneiss and schist. The Swayze mine was discovered in 1867 and closed in 1889, while the Turkey Hill mine was opened in 1872 and closed in 1887. The dip-needle survey covered 266 acres. The diamond drilling comprised 11 holes totaling 4,910 feet from which 142 samples were taken for chemical analyses. Old mine dumps were sampled at 52 points for chemical and magnetic analyses.

Jan 1, 1948

By G. R. Hopkins

According to reports as of January 1, 1931, the total daily charging capacity of the cracking plants, hoth completed and under construction, in the United States amounted to 1,950,781 "barrels, an increase over the previous year of 14 per cent. The total daily capacity of the operating plants amounted to 1,594,990 "barrels, or 82 per cent of the grand total, the capacity of the in¬ operative plants was 244,661 "barrels, or 12 per cent of the total, while the capacity of the plants under construction amounted to 111,130 "barrels, or 6 per cent. In comparison with a year ago, these data indicate a decline in the total capacity of the plants "being "built "but show material increases in the capacity of "both the other two classes. The increase in total inoperative capacity and the decline in construction in 1930 undoubtedly resulted from un¬ satisfactory economic conditions. The total number of cracking units completed or under construction on January 1, 1931, totaled 1,863 as compared with 2,002 the previous year and with a high of 2,559 on June 1, 1926. During the period between June 1, 1926, and January 1, 1931, the total charging capacity of the cracking plants has more than doubled, but the number of units has shown a material decline. This condi¬ tion has been brought about largely through the dismantling of many Burton still of small capacity and through the tendency to increase the size of the new units The "largest unit that can be identified in this survey has a daily charging capacity of 10,000 barrels, but undoubtedly there are some that would exceed this in size. Texas, with a total of 575,300 barrels, ranked far ahead of the other States in charging capacity, and was followed in order by California, Indiana, Oklahoma, and Pennsylvania. Indiana, with only five refineries, ranked third in cracking capacity, which illustrates the importance of the Chicago district as a gasoline-producing center. Not all of the States showed a gain in capacity during the year; in fact, four of them, namely Illinois, Louisiana, New York, and Oklahoma, reported a decline.

Jun 1, 1931

By R. G. Sandberg

Many gold-bearing ores throughout the Western United States contain small quantities of mercury. The presence of mercury not only decreases the gold-loading capacity of the activated carbon, but complicates the fire refining of cathodes and creates a potential health hazard. The Bureau of Mines investigated methods to limit mercury extraction during gold ore leaching and to remove mercury from cyanide leach solu-tions. Mercury dissolution was reduced from 40 to 10 pct by decreasing NaCN concentration from 20 lb to 0.34 lb per ton of solution at a pH of <11. When 0.1 lb CaS per ton of ore was added to a leach slurry, mer-cury extraction was reduced from 27 to 0.4 pct. Less than 0.5 pct of the mercury was solubilized when <0.1 lb CaS per ton of are, along with lime and NaCN, was added to a simulated grinding circuit.

Jan 1, 1984

By Paul C. Hyndman

Three properties in the Tuolumne River RARE II area, the Eagle Bluff Mine (lode) and the Indian Creek Bar and Bossy Bar Prospects (placer), have identified subeconomic gold resources (table 1). Nineteen other properties have potential for gold resources. Adjacent to the study area, five properties have identified mineral resources, and nine others have potential for resources. Properties having high-grade zones (shoots), but licking enough tonnage to be classified as resources, are listed in table 2. Gold, in lode and placer deposits, is the principal mineral commodity in the Toluene River study area. Ten properties within the RARE II boundary have gold-rich zones or shoots; they range in size from 12 to 2,500 tons and in average grade from 0.09 to 0.97 oz gold per ton.

Jan 1, 1983