Search Documents

By R. C. Gabler

Laboratory tests on a combined nitrogen roast--two-stage leach--electro-winning approach show promise as a possible process for recovering copper, sulfur, iron oxide, and valuable minor metals (gold, silver, and molybdenum) with a minimum impact on the environment. During the nitrogen roast at 800° C, 15 to 20 percent of the sulfur together with a significant fraction of the volatile elements, such as arsenic, bismuth, lead, and zinc, are removed from the chalcopyrite concentrate. The resulting calcine, consisting of 8-chalcopyrite, troilite, and a bornitelike structure, is leached with hydro-chloric acid to remove 70 to 85 percent of the iron. The digenite in the leach residue is dissolved in an oxygen-saturated, spent sulfate electrolyte. Using a graphite 'anode plus sulfur dioxide to reduce interference from ferric iron, copper of 99.99+ purity is electrowon at current efficiencies of 88 to 92 percent and a cell voltage of 0.4 to 0.5 volt. Copper recovery for the overall process is 98 to 99 percent. Sulfur is obtained in the elemental form from the roasting and leaching steps. Iron can be recovered from the hydro-chloric acid leach solution. Gold, silver, and molybdenum are concentrated in the silica residue from the spent electrolyte leach.

Jan 1, 1975

By W. H. Carrington, A. C. Richardson

"INTRODUCTION The Powhatan mine of the Franklin Coal Mining Co. is located in the western part of Jefferson County, Ala., on the Louisville and Nashville Railroad, 40 miles west of Birmingham. The Mary Lee bed at this point yields coal with fair coking qualities, but with an ash content as mined so high as to prohibit its use in the production of metallurgical coke. At present the entire output of the mine is washed in single-compartment jigs and marketed as locomotive and domestic fuel.Figure 1 gives a typical seam section of the Mary Lee bed at the Powhatan mine. This section shows that the bed is divided by rock partings into three benches. In many parts of the mine, particularly in the older workings the roof rock is so weak that it can not be held without excessive timbering. This condition has restricted the operation in many parts of the mins to the middle and bottom benches of coal. The 6 inches of draw rock between the top and middle benches is very strong and makes an excellent roof requiring only a normal amount of timbering to support it. In the newer workings of the mine the character of the rock above the top bench is strong and it is believed that in the future it will be possible to work all three benches. This study was undertaken for the purpose of determining the washing characteristics of the Mary Lee bed at Powhatan and the effect on these characteris-tics of including or omitting the coal from the top bench. It was also the purpose of the study to show whether it would be possible to produce a washed product sufficiently low in ash to be used for the manufacture of metallurgical coke. This paper is one of a series of reports on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and tin University of Alabama. With the cooperation of the coal producers of Alabama. It contains the results of screen sizing and float-and-sink tests of representative samples of run-of-mine coal, and the results of table tests on the minus 3/16-inch sizes of the raw coal."

Apr 1, 1933

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By Peter G. Kovalchik, Lawrence W. Scott, Thomas H. Dubaniewicz, Mark A. Fuller

Mine trailing cables operated above safe thermal limits can cause premature insulation failure, increasing electrocution and fire hazards. Previous U.S. Bureau of Mines Pittsburgh Research Center research showed that, under static test conditions, electrical current levels permitted under present regulations may not limit cable temperatures to less than the 90 °C rating of reeled trailing cable. Continuing research under the National Institute for Occupational Safety and Health (NIOSH) addresses thermal characteristics of reeled trailing cable under dynamic test conditions more representative of field conditions, where operators constantly reel in and pay out cable. This research is in support of efforts by industry associations and the Mine Safety and Health Administration to establish safety guidelines for cyclically rated reeled machines. This paper describes a unique approach to measuring temperatures within reeled cable under dynamic test conditions. Fiber-optic sensors embedded within the metallic conductors measure temperatures at 1-m intervals along the entire length of cable. Temperature measurements are reported to be accurate to within 1±° C. The test setup requires access to only one end of the trailing cable, allowing researchers to freely reel in and pay out cable while temperature measurements are made, simulating field conditions. Manufacture of a fiberoptic-embedded trailing cable is described, along with initial test results that indicate the fiber-optic approach is viable.

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage bf measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known, There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught fire, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known. There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught firs, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By D. O. Kennedy

"INTRODUCTION During the recent war attention was directed to prevent the destruction of American industries by sabotage. By Executive order of Lay 19, 1942, the Bureau of Mines was required to conduct investigations and make recommendations that would prevent loss of production of essential war minerals. The Health and Safety Branch of the Bureau of Lines was able to extend its activities with minimum loss of time to include security surveys of the important mineral facilities in the United States.A Mineral Production Security Division was established in the Health and Safety Branch with funds appropriated for that purpose by Congress in April 1942. From July 1942 to July 1945 engineers of this division, under the direction of D. Harrington, Chief, Health and Safety Branch, and J. J. Forbes, Chief, Mineral Production and Security Division, conducted investigations of 1,560 metallic and nonmetallic mines and associated facilities in accordance with the requirements of the Executive order.PURPOSEAn analysis of losses in the production of minerals shows that failure or destruction of equipment either from deliberate or accidental causes produces essentially the same result. Maximum production is insured by the prevention of subversive activities, fires, and industrial accidents."

Sep 1, 1946

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point, out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By Linneas Laage, Thomas Weber, William Pomroy

"Underground mine fires can significantly influence mine ventilation airstreams, in some cases throttling or even reversing airflows. As a result, the performance of a metal and nonmetal mine stench fire warning system, which depends on the ventilation to carry the vital warning signal, under fire conditions is different from performance under nonfire conditions. The safety of underground miners can be jeopardized if the warning signal is delayed. This Bureau of Mines report describes research to investigate fire and stench warning system interactions. A computer model is presented that permits quantitative analysis of stench warning signal delays as a function of fire location and intensity. The results of a case study involving computer simulations of stench distribution in a hypothetical mine network subject to various fire exposures are also discussed. This case study illustrates a technique for identifying the areas within a mine that are subject to unacceptable warning signal delays, thereby enabling preemptive action by mine personnel, such as redeployment of stench injectors. INTRODUCTIONFires are an ever-present threat to the safety of underground miners. Since the smoke and toxic gas produced by a mine fire can be spread rapidly by the mine's ventilation system, mine evacuation must be accomplished as quickly as possible in the event of fire. In metal and nonmetal mines, the most common means of passing the fire warning signal to each miner is the stench system. The typical stench system utilizes ethyl mercaptan, a highly odoriferous organic compound, injected on the surface into the compressed and/or ventilation airstreams. Upon smelling the stench, workers evacuate the mine according to an emergency preplan.Although the stench system has been used successfully for over 60 yr, it has several serious shortcomings, owing to certain chemical properties of ethyl mercaptan and to certain performance characteristics and limitations of present injection systems.Recent Bureau research succeeded in upgrading the overall safety and effectiveness of the stench system through the use of a superior stench odorant and the development of improved stench injection equipment (1).4 This research has also investigated a specialized computer simulation model capable of calculating the precise concentration of stench in any mine ventilation network branch at any time after stench release (2). An adaptation of the computer model now enables the analysis of stench system and ventilation system interactions under the influence of a mine fire."

Jan 1, 1987

By Peter J. Clarke

The Soviet-controlled Government in Afghanistan continued to emphasize development of the country's mineral resources, primarily to supply raw materials and fuel to industrial areas in the Soviet Central Asian republics. In addition to expanding production of natural gas for export to the U.S.S.R., a $600 million2 Soviet-Afghan cooperation project, 1 of 167 such projects established since 1981, was devoted to exploiting the Ainak copper deposit, south of Kabul in Logar Province. Also being developed was the large Hajigak iron ore deposit in the Hindu Kush Mountains, 100 kilometers northwest of Kabul. In addition to these minerals, Afghanistan already produced small quantities of barite, cement, coal, gypsum, salt, and possibly some lapis lazuli. Afghanistan was the world's leading producer of lapis lazuli, a semiprecious gem stone, prior to the Soviet invasion in 1978, but production, although no longer reported, has probably been significantly reduced. It was also reported that Soviet mining engineers and technicians have commenced producing uranium from Lashkangah in the mountainous Khawaja Rawash area near Kabul.3 The Government was also considering mining chromite from Herserak and Mohammed Agha Kulanger, near the border with Pakistan.4 Afghanistan's overall economy remained stagnant in 1983, a result of continuing armed resistance to the Soviet-installed government. The gross domestic product (GDP) was estimated at about $2.8 billion, only marginally higher than the 1982 level. The value of exports was estimated at $720 million, up less than 2% over that of 1982, while imports rose approximately 8% over the same period. Natural gas was by far the leading export, earning about $295 million, up 4% over that of 1982. Approximately 90% of Afghanistan's natural gas production was exported to the U.S.S.R. Gas exports were used to pay the country's debt to the U.S.S.R., and also to pay for its supplies of petroleum products and other goods, which were imported almost exclusively from the Soviet Union. Some of Afghanistan's petroleum products were supplied by the U.S.S.R. as grants in aid, as Afghanistan did not have any domestic petroleum refining capacity.

Jan 1, 1985

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008