Search Documents

By Francis E. Federspiel

Based on the investigation by the Bureau of Mines, tungsten is the principal metal found in the study area; gold and silver were the primary metals found at one property. Tungsten occurs in tactite zones formed near contacts of calcareous metasedimentary with granitic intrusive rock. Gold and silver were found primarily along quartz veins in granitic rocks; small amounts of those petals also occur in the tactite zones. Since 1856 approximately 200 lode claims or relocations have been recorded, mainly in the southwest corner of the study area. Tungsten production in this part of the area has been inure than 7,800 short ton units (70,800 kg) of tungsten concentrates; about 4,800 short ton units (43,500 kg) were from the Mud Lakes Mine; and 3,100 short ton units (27,200 kg) were from the Rainbow Mine 1/.

Jan 1, 1981

By David A. Lipton

In 1980, the U.S. Bureau of Mines conducted a mineral survey of the 23,500 acre Garcia Mountain RARE II area (No. 5107) in the Los Padres National Forest. Bureau of Mines data indicate a low potential fur gold, silver, and mercury resources. Twenty-nine placer samples, representative of small yardages, showed small amounts of gold or other economic mineral values. Mercury deposits in faulted siliceous rocks in the Franciscan Formation occur north of the area. Similar rocks are in the southwest part of the study area, but apparently contain no mercury deposits. Geothermal and oil and gas potential is low.

Jan 1, 1982

By William E. Wallace, S. J. Page, B. L. Razzaboni, C. A. Hill, Pamela Mike, P. Bolsaitis, M. J. Keane, Val Vallyathan

"Respirable quartz cytotoxicity, as measured by erythrocyte hemolysis and pulmonary macrophage release of lactate dehydrogenase in vitro, is neutralized by boiling in water in glass test tubes for 10 to 40 minutes. The cytotoxicity is reduced to near zero by boiling l to IO mg quartz per milliliter water. For greater concentrations of quartz in water the hemolytic potential after 40 minutes of boiling approaches that of native quartz. Replacing the medium with fresh water midway through boiling results in full detoxification through 20 mg quartz per milliliter water. Pre-boiling the medium with silica reduces the detoxification effect. Detoxification persists after mild drying at l 10°C for 8 hours, and persists after three days of resuspension in water at room temperature.INTRODCJCTIONResearch underway to determine interactions of quartz and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages were suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosmal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121°C with no liquid water but with steam present. 1.2 However detoxification under boiling conditions has been reported in other research. 3 It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity simplicity and cost.RESCULTS AND DISCCISSIONRespirable quartz dust used in this study was taken from a stock of crystalline silica, Min-U-Sil; obtained from Pennsylvania Sand Glass Corporation, fractionated in air with a particle classifier. The small size fraction retained for use was 80% less than S micrometer particle diameter, with an area equivalent median diameter of 1.24 micrometers as estimated by automated image analysis. The silica was at least 98.S mass percent silica as determined by X-ray energy spectrometric analysis; and the crystalline form was alpha-quartz as determined by X-ray diffraction. It's specific surface area was 3.97 square meters per gram as determined by nitrogen adsorption isotherm methods. I"

Jan 1, 1990

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983

By E. W. Pehrson

In making any canvass of secondary metals great care must be exercised to avoid duplication or exaggeration of net consumption. One of the major difficulties is to trace the metal accurately as it passes through the many cycles of manufacture. Greater or less duplication probably occurs in any canvass. The manufacturer of tin plate, for instance, purchases primary pig tin exclusively as a raw material. Most of it goes into the coating on the steel sheet, but a substantial part emerges in the form of byproducts such as scruffs and drosses. These are sold to other plants, where they are used in the manufacture of alloys and chemicals. Alloys and chemicals, however, are not necessarily articles for final consumption. The alloy may be sold in ingot form to a bearing manufacturer, who, in turn may produce some scrap, which he may sell to still' another plant that may make still other products. There is a considerable return of tin in the form of waste products from chemicals sold to the silk industry. Even tin plate does not represent an ultimate use of tin because the tin-can maker produces large amounts of clippings, which are sold to detinning plants, where the tin is recovered and used again for some other purpose. Thus the degree of duplication in consumption statistics depends on the point in the industrial cycle where consumption is measured.

Jan 1, 1936

By Charles H. Atkinson

The Rio Blanco massive hydraulic fracturing demonstration has been undertaken by the Bureau of Mines, Atomic Energy Commission, and a group of 15 industry participants. CER Geonuclear Corp. has been retained as program manager to evaluate the stimulation effects of very long fractures, suitably propped open in thick sections containing multiple intervals of low-permeability gas-bearing sands. The zone of interest for this demonstration includes Fort Union and Mesaverde sands from about 5,800 to 8,.200 feet deep in Rio Blanco County, Colo., about 1 mile from the site of the May 1973 triple nuclear detonation aimed at stimulating production from the same reservoirs. Drilling the test well and evaluating the reservoir prior to fracturing was funded by Government participants; fracturing and production testing will be funded by industry. The test well has row been completed at a total depth of 8,170 feet, and data obtained from logs, cores, production and drill-stem tests indicate reservoir conditions to be less favorable for gas production than anticipated. Structural position is lower than expected, resulting in higher water saturation than was determined for the same sands at the nuclear fracturing location. The lower sands of the Fort Union sequence appear to have higher shale content than has been encountered in other wells in the area. Despite the likelihood that gas productivity will be undesirably low following stimulation, the industry participants decided to proceed with the stimulation program with the thought that the resulting data would be useful. The success of the stimulation test probably will have to be judged by production increase rather than by production volume.

Jan 1, 1975

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By D. E. Seizinger

The Bureau of Mines has developed analytical methods, primarily gas chromatographic, for measurement of exhaust oxygenates produced from selected simple fuels. The resulting data were used to estimate levels of carbonyls and noncarbonyl oxygenates in exhaust from gasoline fuels. Estimated noncarbonyl oxygenates in gasoline exhaust may comprise as much as 30 pct of total oxygenates which include unsaturated carbonyls and noncarbonyls believed to be significant potential pollutants.

Jan 1, 1972

By J. B. Gayle

This investigation was conducted by the Federal Bureau of Mines to compare the selectivities of diverse flotation reagents and also of flotation and float-sink methods of separation. Flotation tests, using sodium chloride, an alcohol-type frothing agent, and a kerosine-pine oil mixture as reagents, were made on seven coking-coal samples representing four different beds. The results indicated equivalent selectivities relative to sulfur rejection when entrapment effects were minimized by recleaning the various products. Selectivities relative to ash rejection were also equivalent for some coals; for others, the selectivities of the reagents tended to increase in the order sodium chloride, alcohol-type frother, and kerosine-pine oil. Float-sink tests on these same coals generally gave results indicating better selectivities than those obtained in flotation tests at comparable levels of recovery.

Jan 1, 1960

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. In this volume and in a series of Reports of Investigations immediately following the factual data obtained during the project are reported. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location und name are shown on the appropriate half-township map.-The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this eeri88 of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1 (R. I. 4251). The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table tor each half township is given with the discussion covering that area.

Jan 1, 1948

By Douglas F. Scott

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the Pyramid RARE II area (No. 5023) covering 23,500 acres (9,500 ha) of E1 Dorado National Forest and 7,900 acres (3,200 ha) of the Lake Tahoe Basin Management Unit (fig. 1). The Bureau of Mines investigation did not reveal mineral deposits in the area. Samples taken from silicified and limonite-stained metasedimentary rocks and aplite dikes were void of precious or base metals or uranium. Placer samples from stream gravels contained no gold values. Molybdenite occurs in quartz stringers within quartz monzonite near Grass Lake, adjacent to the area; no extension; were found in the area.

Jan 1, 1982

By E. L. Rawlins

A previous report4 has explained that pipe lines for the transmission of natural gas should be buried to minimize temperature fluctuations because when excessive the latter decrease accuracy in measuring gas volume and increase leakage of gas due to expansion and contraction in the pipe joints. These effects are governed by the rapidity of the temperature fluctuations and by the total variation over a period of time. The temperature of gas flowing through a pipe line depends to a large extent, upon the temperature of the ground adjacent to the pipe; hence, fluctuation of the ground temperatures at various depths determines the economic depth at which pipe lines should be buried. Scope and Purpose of Report This report covers a record of the daily atmospheric temperature fluctuations at Bartlesville, Okla., for 12 months and a-similar concurrent record of the temperature variation 1, 2, 3, and 4 feet below the surface of the ground.

Jan 1, 1928

By J. H. Jansky, P. W. Jeran, G. L. Hassett, M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emissionin 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States had daily methane emissions of 1 MMcfd or more, These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va,, which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.5 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1975

By J. O. Jones

[Willis Mountain in southeastern Buckingham County is one of several kyanite deposits its central Virginia. It is composed principally of kyanite resulting from metamorphism of siliceous sedimentary beds rich in alumina. The mountain, which trends north-south, is 2 miles long and is topped by a narrow ridge with sleep rugged sides rising to an altitude of 1,160 feet and projecting 500 fast shove the surrounding countryside. Bureau Mines engineers examiner Willis Mountain early in 1949, when bonded concentrations of coarsely crystalline kyanite were observed in the kyanite-quartzite on the northern end of the mountain and in loose boulders on the eastern slope. Commencing in late July 1949, the investigations continued on the Long Mountain segment for 11 months, ended in June 1950. A total of 600 samples from 32 diamond-drill holes, aggregating 3,876 feet of drilling, and from 255 feet of sampling in 3 trenches was assayed for kyanite and ferric oxide.]

Jan 1, 1954

By Hal J. Kelly

A picture of the ceramic industrial potential of the Pacific Northwest States is presented by reviewing the present ceramic industries, raw-material resources, and current market demands. A resume is given of the industrial plants manufacturing ceramic ware as well as available information on raw-material resources. No attempt was made to prospect for new deposits but rather to evaluate, insofar as possible, those already known. Since much of the industry is concentrated on the Pacific coast, most of the information available on resources concerns deposits in that area. Large, undeveloped districts in Montana and Idaho, however, offer promise of larger reserves of ceramic raw materials. Average annual production, some operating costs, and annual power consumption are given for each of the plants. Production and some cost figures are listed to show the limited nature of the present industry and to suggest fields open for new development.

Jan 1, 1956

By Paul M. Ambrose

ADVANCES in mining and processing technology made it possible to reopen the De Beers diamond mine in South Africa, originally located in 1871 by Cecil Rhodes and closed in 1908. Radioactive material was used to indicate the efficiency of hydro-cyclones used in diamond concentration. Added interest was shown in recovering diamond from the sea off the coast of South-West Africa. Production of crude artificial abrasives declined because demand was paritally met by withdrawals from stocks. The value of graded grain-coated abrasives and grinding wheels surpassed those of 1962.

Jan 1, 1964

By T. J. Ballard

Corundum is a natural alumina (A120 ) and is next to the diamond in hardness . Except for the gem varieties , it is used principally as an abrasive , chiefly in grinding , dressing , and polishing metals and optical glass . Natural corundum is preferred to artificial abrasives for certain specialized jobs . Most of the corundum ( excluding emery ) mined in the United States came from the Corundum Hill mine in North Carolina and the Laurel Creek mine in Georgia . The Corundum Hill mine provided over half of the domestic production of corundum prior to 1900. Since 1900 , the importation of foreign corundum and the manufacture of artificial abrasives caused the decline of corundum mining in the United States .

Mar 1, 1947

By P. T. Brooks

The selective recovery of nickel and cobalt from impure raw materials is being investigated by the Bureau of Mines as part of a program to develop improved procedures for preparation of pure metals. A combination solvent extraction-electrolytic process has been developed in the laboratory that enables preparation of high-quality nickel and cobalt from nickel oxide containing, in percent, 76 nickel, 0.8 cobalt, 0.5 magnesium, 0.2 iron, and lesser quantities of copper, zinc, and other metals. The oxide was smelted, using carbon as reductant, and cast into anodes. These anodes subsequently were dissolved in diaphragm-type electrolytic cells. Nickel and cobalt were deposited separately from appropriate electrolytes, concurrent with dissolution of the impure anodes. Anolyte containing nickel and cobalt in the form of chlorides and sulfates was treated for removal of impurities and separation of nickel and cobalt. First, iron and aluminum were removed as hydroxides by adding nickel hydroxide to raise the pH of the anolyte from 2.3 to 4.5. Next, the pH was adjusted to 2 by adding hydrochloric acid, and the solution was treated by solvent extraction to separate nickel and cobalt.

Jan 1, 1963

By John D. Bardill

This report covers magnetic surveys in the Dannemora arca , which was part of a general survey of magnetite deposits in New York started in 1943 . The objective of these surveys was to afford a basis for the selection of exploration projects .

Jan 1, 1947

By K. P. V. Lei

The Bureau of Mines as part of its research effort to minimize the generation of hydrometallurgical waste, investigated a sodium sulfide leaching-electrolysis procedure for treating hydrometallurgical residues for elemental sulfur and base-metals recovery. Research was conducted on a leaching residue from a lead concentrate. The following procedure was developed. 1. The elemental sulfur was dissolved as polysulfide with an Na2S solution. 2. The resultant metal sulfide bearing residue was oxidatively acid leached in a cationic membrane electrolysis cell; the metals were solu¬bilized at the anode, and a base was generated at the cathode. 3. The elemental sulfur was recovered from the polysulfide solution by neutralizing with the acid in the anolyte. Byproducts of the neutralization were H2S and a sodium salt solution. 4. Sodium sulfide was regenerated by reacting the H2S byproduct with the base in the catholyte. 5. Lead as PbCL2 was recovered from the anode residue by brine leaching, and the other metals were recovered from the sodium salt solution as metal sulfides. 6. The barren filtrate from the metal sulfide precipitation constituted the recycled electrolyte. Ninety-eight percent of the elemental sulfur, 98 pct of the lead, and up to 80 pct of other accessory metals were recovered from a residue obtained from the FeCl3-NaCl leaching of a lead concentrate.

Jan 1, 1982