Search Documents

By D. J. Parker

Since the introduction of electricity into the mines of the United States , the hazards incident to the industry have increased materially in both coal and metal mines . For economic reasons the tendency at present , particularly in coal mining , is decidedly toward the adoption of electrical mine machinery , including alternating current machinery , on a more extensive scale than ever before . Obviously, the growing use of such equipment will result in an ever -increasing number of underground transformer stations . The principal electrical hazards in mines are threefold ; fire , explosion, and contact . Of these , fire is the greatest hazard involved in the use of electricity underground , and several fires have originated in underground transformer and motor generator set stations . The fire hazard due to improperly installed and poorly maintained underground transformer stations is an ever-present one , and failure to take the necessariman remedial action is likely to result , sooner or later, in the destruction of life and property . Upon suggesting the necessary corrective measures with respect to such installations , one is often confronted with the statement to the effect that even though this particular hazard has existed over a period of years , there have been no unfavorable results therefrom thus far . Frequently , the desirability for action is not apparent to the mine management until it is too late . Because a mine has a record free from fires , explosions , etc. , over a number of years of operation during which these hazards existed , such good fortune should not be taken as a guarantee that this or any other mine is immune from these common dangers . When the elements of an existing hazard are properly balanced or in the right proportion, the unfortunate combination must of necessity culminate in misfortune of one kind or another. The fire hazard due to underground transformer installations can be very definitely minimized by proper installation and maintenance . In coal mines the transformer banks , connected to 2,300 and occasionally to 4,400 volt circuits , are often found located in open- ended crosscuts , mounted on concrete or timber foundations , and in nonfireproof surroundings .

Jul 1, 1930

By R. E. Kennedy

The presence of combustible gases and vapors in air can constitute n extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and. allied industries, the U. S. Bureau of Mines has investigated the explosive properties of a number of gaseous and liquid compounds; the results of these investigations have been published in various government papers and journal articles. The increased use of liquefied, petroleum gases has intensified interest in the effect of high pressures on the explosibility of propane-air mixtures. The limits of flammability of natural gas-air mixtures have been determined at pressures ranging from 50 min. Hg to 3,000 p.s.i. As it is known that a combustible. gas or vapor cannot burn or explode when the oxygen content of the atmosphere is less than a certain value, critical values were determined for the oxygen content of atmospheres to which nitrogen had been added as a diluent. In this connection limits of flammability were determined for ethane in atmospheres containing added. nitrogen or carbon dioxide at pressures up to 900 p.s.i.g.

Jan 1, 1951

By H. H. Schrenk, F. E. Griffith

"The increase in tunneling operations that requires working under pressures greater than that of ordinary atmosphere has raised the question of the use and possible limitations of respiratory protective devices under such unusual conditions. As little, if any, information is available, there is need for a comprehensive study of this subject before specific recommendations can be made. In the absence of such data it seems desirable to make a few preliminary observations regarding the problems associated with wearing respiratory protective devices under increased air pressures.Two distinct problems must be considered--the mechanics of the apparatus used under such conditions and the physiological effects of increased pressures on wearers of respiratory apparatus. This report is confined to the use of oxygen breathing-apparatus and gas masks under pressure.ACKNOWLEDGMENTSThe data presented were obtained at the Queens Midtown Tunnel under construction at the east end of 42d Street, New York City, during a study of compressed-air illness conducted by the Bureau of Mines in cooperation with the United States Public Health. Service and the New York City Tunnel Authority.Grateful acknowledgment for cooperation and the use of facilities is made to Dr. R. R. Sayers and his associates, particularly Dr. J. W. Crosson (who acted as observer during the oxygen breathing apparatus tests), of the Division of Industrial Hyiene, National Institute of Health; to the Port of New York Authority, through Dr. Edward Levy; end to the contractors, through Doctor Emery."

Jan 1, 1940

By A. C. Fielder

It is with some diffidence that I venture to address the Montreal Section of the Society of Chemical industry on the subject of motor fuel from coal at a time when crude petroleum is produced in greater quantities than at any time in history, and at a time when the known reserves exceed all expectations, even the optimistic estimates of the Committee of Eleven of the American Petroleum Institute. Not only are new fields being discovered in America a -an embarrassing frequency but sources outside of the North American Continent show, unmistakable signs of adding materially to the world's sources of oil. Were it not for the tremendous scientific and technical importance of the work done in the past few years in transforming coal into liquid motor fuels, I should prefer to let this subject rest until a more propitious time, such as prevailed some years ago, when the gasoline consumption curve was rising rapidly and the production curve was slowing in its upward rise. That was the period which stimulated the researches which resulted in tetra ethyl lead and anti-knock gasolines on this side of the Atlantic and in methanol, synthetic gasoline and hydrogenation of coal on the other side. Some of you will recall a symposium on Motor Fuels and Oil Conservation held at the Chemists' Club n New York in September; 1925. Dr. R. L. Brown and I presented a paper at this meeting on "Complete Utilization of Coal and Motor, Fuel, in which we pointed out that coal was the most likely raw material source of gasoline substitutes if and when needed. We grouped the present and future, processes' for obtaining motor fuel from coal in three classes, namely:

Jan 1, 1928

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

By V. E. Homme

This report describes methods of using sodium for reducing titanic chloride, developed as part of Bureau of Mines activities at Boulder City, Nev., to improve the extractive metallurgy of titanium. Theoretical indications pertaining to the major chemical reactions and possible side reactions of the process are compared with experimental observations. Low-temperature reduction equipment is described, in which titanic chloride was reduced with sodium at temperatures between 97.5° C., the melting point of sodium, and 200° C. Techniques employed in making reductions in ball-mill and high-surface sodium reactors are given.

Jan 1, 1958

In spite of advances in measurement techniques and an explosive increase in the volume of research, our understanding of human strength remains in its introductory stages. It is clear that muscle strength is a highly complex and variable function that depends on a large number of factors. It is not surprising, therefore, that large differences in strength exist not only between individuals, but even within the same individual tested repeatedly on a given piece of equipment. The issue is compounded by the fact that correlations of strength among different muscle groups in the same individual are generally low, and tests of isometric strength do not necessarily reflect the strength an individual might exhibit in a dynamic test. As a result of these and other influences, great care needs to be exercised in designing, evaluating, reporting, and interpreting muscular strength assessments. Traditionally, tests of muscular strength were in the domain of the orthopaedist, physical therapist, and exercise physiologist. Such tests are also an important tool for the ergonomist, however, because of the high strength demands on workers in manual materials-handling tasks. In some cases, task demands may approach or even exceed the strength that an individual is voluntarily willing to exert in a test of strength. In such cases, evidence suggests that the likelihood of injury is significantly greater than when the task demands lie well within an individual's strength capacity. Because the relationship among strength capabilities, job demands, and musculoskeletal injury has been established, it is apparent that tests of muscular strength may benefit the ergonomist both in designing jobs and in ensuring that individuals have sufficient strength to safely perform physically demanding jobs. Several strength assessment techniques have been employed for these purposes, each possessing unique characteristics and applicability to job design and worker selection procedures. Our main purpose has been to elucidate these strengths and weaknesses, so that tests of strength may be properly applied in designing jobs and selecting workers. One of the crucial points we have emphasized is that any test of strength used in job design or worker selection must be directly related to the demands of the job.(1) For example, if an occupational lifting task has a high dynamic component, a test of isometric strength is not likely to provide the data necessary for proper design of the job. Of course, dynamic strength tests would also be misapplied in assessing a job requiring isometric exertions. Another potential pitfall is using tests of strength on isolated muscle groups and assuming that they are indicative of whole-body strength. For example, one might mistakenly assume that dynamic trunk extension strength represents a person's capability to perform a lifting task. However, an individual's lifting capacity may be entirely unrelated to trunk extension strength. It may, instead, be limited by an individual's arm or leg strength, depending on the task being performed. A final point on strength assessment should be made. An individual's strength capability cannot be considered a fixed human attribute. Strength training regimens can increase an individual's strength capability by 30%-40%. Whether

Jan 1, 1998

[~lis is the f'fth in a ~erieG of reports on properties of commercial motor fuels, made in accordance 1,'Vi t:h fl cooperative ae,ree-ment betwGon tho Cooperative Fuel ReRRarch (e.F.R.) Committee and the Bureau of I ines of the Dcpart~ent nf the Interior. The first report gave data on motor r-asolino~ sold during the wintor of 935-36.31 Thi~ report covers 84 brands of ga~oline represented by l,722 samples exclurling the Pacific Coast. T 3)Se J.rom th~. ?~'tcific Coast IV .ro avnrL)f:od b~r tho Pacific Coa!3t tecilnical group "bofore o8ing submi ttcd ruld arc p~.lbl:'shcd GX Gtl~r as they were submi tted. In some areas r~lJort~ . erc roceivod f~om ~ ix to eicht compD.l1ie~ on the same brands of gasoline. whoruar. in other areas only one company reported on a brond. Thut., it CU .. "! be senn that BO .. 0 uf the dnt ;.U'e more rCY>l'c entat vc thM others. The inclusion of r~0rts fro:n several ci tie. w' thin somo of tho di stricts has ir.rpr,)vcd the report by reducinc; tr.e numb~r of brand rcportel by only ono company. ]

Jan 1, 1938

[~lis is the f'fth in a ~erieG of reports on properties of commercial motor fuels, made in accordance 1,'Vi t:h fl cooperative ae,ree-ment betwGon tho Cooperative Fuel ReRRarch (e.F.R.) Committee and the Bureau of I ines of the Dcpart~ent nf the Interior. The first report gave data on motor r-asolino~ sold during the wintor of 935-36.31 Thi~ report covers 84 brands of ga~oline represented by l,722 samples exclurling the Pacific Coast. T 3)Se J.rom th~. ?~'tcific Coast IV .ro avnrL)f:od b~r tho Pacific Coa!3t tecilnical group "bofore o8ing submi ttcd ruld arc p~.lbl:'shcd GX Gtl~r as they were submi tted. In some areas r~lJort~ . erc roceivod f~om ~ ix to eicht compD.l1ie~ on the same brands of gasoline. whoruar. in other areas only one company reported on a brond. Thut., it CU .. "! be senn that BO .. 0 uf the dnt ;.U'e more rCY>l'c entat vc thM others. The inclusion of r~0rts fro:n several ci tie. w' thin somo of tho di stricts has ir.rpr,)vcd the report by reducinc; tr.e numb~r of brand rcportel by only ono company.]

Jan 1, 1938

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By Gregory M. Molinda

The U.S. underground coal miner faces a continuing hazard from the fall of roof. At the root of many injuries and fatalities are weak or defective roof strata. Throughout mining history, millions of miles of entry have provided exposure of every conceivable geologic roof hazard. This report describes the geologic origin, association, and potential danger from the most common hazards. Discussions of weak rock include drawrock, rider coals, head coal, stackrock, and stream valley effects. Discontinuities, or roof defects, are described including, clay veins, slickensides, joints, and paleochannels. A number of examples from U.S. coalfields are used to document geologic structure and associated hazards. Roof fall analysis is a methodology used by NIOSH for hazard recognition and prevention; its application and benefit to the industry are discussed.

Jan 10, 2003

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

The computer program has been developed in conjunction with the rest of the project to evaluate evacuation capabilities of the mines and develop guidelines for the escape systems. There are several problems associated with predicting evacuation performance of a mine. First, the mine has many interconnected passages, shafts, hoists and a number of miners in varying positions. To be able to predict evacuation time requires processing a hugh amount of data. A simplistic approach of determining the miner farthest from the exit and calculating evacuation time for him knowing his walking speeds and hoisting times is not realistic, since the waiting time for the hoist is neglected. The second problem is being able to repeat the calculations for a number of configurations. It may be possible to spend enough time to hand calculate the evacuation parameters for a single mine for a single configuration, but to evaluate capabilities of the evacuation

Jan 1, 1976

By Paul E. Loustaunau, Devah Galloway, Catherine Wetherby

This report describes a project in which Development of a Supervisory and Management Training Program for the Underground Coal Mining Industry was developed and evaluated. The project was carried out in two phases. The first phase was a research effort to develop specifications for the program. The second phase was a development and evaluation effort. In the second phase, training programs for first-line supervisors (section foremen) and for middle managers (mine/shift foremen and mine superintendents) were prepared in accordance with the specifications and evaluated by members of the industry. This report describes the project and presents the conclusions drawn there from.

Jan 5, 1983

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

By J. S. Browning

The physical properties and specific gravity ranges of various liquids and salt solutions used for laboratory sink-float separations of rocks or minerals are presented. The test equipment and techniques employed by the Bureau of Mines in making sink-and-float separations of particles as coarse as 3 inches to as fine as 400 mesh are described. Also discussed are methods of recovering and reclaiming the liquids or salts from the minerals and wash solutions, as well as the hazards encountered and precautions to be followed while working with the materials. The laboratory use of various liquids for separating minerals of different specific gravities has been recognized for many years. During this time, laboratory sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations, such as those producing mica, spodumene, kyanite, and so forth. These procedures also have been used as analytical tools for determining the mineral content and associations of other metallic and nonmetallic ores.

Jan 1, 1961

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By John L. Hill

"The Bureau of Mines is conducting research on the causes and methods for control of cutter roof failure in underground coal mines. This hazardous ground control problem exposes miners to the danger of falling roof rock and frequently results in massive roof failure. This report outlines the probable causes of cutter roof failure, which are proposed based on field investigations, numerical model analysis, and in-mine observations. Traditional methods of control are presented, as well as innovative methods based on mining concepts developed during earlier years of coal mining history. The report can be useful to a mine operator for assessing the causes of cutter roof failure on a site-by-site basis and for predicting the probability of its occurrence. A process is presented for selecting an optimum control method that includes both traditional and innovative control techniques for each of the various causes of cutter roof failure. INTRODUCTIONGround control research conducted by the Bureau of Mines is designed to develop technology that will aid in reducing the frequency of accidents associated with poor ground control conditions. Cutter roof failure often poses a safety hazard to miners and causes delays in production while massive roof falls are cleaned up and unstable roof is resupported. Implementation of control measures reduces the threat of injury to miners and prevents production delays.The definition of cutter roof failure used in this report separates this unique type of failure from other ground control problems, to aid in the analysis of the causes and in the development of control methods. The definition is as follows:Cutter roof failure in mine roof rock is a failure process that initially begins as a fracture plane in the roof rock parallel to, and located at, the roof-rib intersection. The fracture propagates upward into the roof over the mine opening at an angle usually steeper than 60° from the horizontal.The mappable extent of cutter failure may range in length from only a few feet to several hundred feet and may traverse entry-crosscut intersections without change in direction. Once initiated along the roof-rib line, a cutter may propagate away from the roof-rib line of one side of a room, cross the roof span, and continue along the other side of the room. It is important to note that this definition excludes a similar type of failure (sometimes referred to as ""kink roof') that has comparable characteristics but occurs in the center of the entry. (The reasons for this distinction are discussed in the ""Background"" section.) Researchers refer to the cutter failure discussed in this report as ""classic"" cutter roof failure; except for short deviations across intersections and entries, initial failure is confined to the roof-rib intersection."

Jan 1, 1986

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979

By Gary W. Krantz

Fibered, portland-cement-based gunite products were applied in the Bureau of Mines Lake Lynn Laboratory Experimental Mine using a variety of pneumatic guns and gunning crews, The demonstrated wet-mix (with silica fume), dry-mix, and surface bonding products were sampled by the Bureau and subjected to a suite of engineering analyses. Gunite flexural and compressive strength, rebound, permeability, porosity, dust loading, shooting rate, crew requirements, and cost factors were evaluated. Steel, fiberglass, or polypropylene fibers were contained in all but two of the gunires tested. Both Bureau and private testing laboratory analyses are provided for some products. Electron probe micro-analysis and X-ray diffraction analysis were performed on the silica fume fraction of the wet-mix gunite to characterize the dust. Aggregate size fraction distribution analyses were performed to provide strength relationships. Results indicate that all of the commercially available fibered-gunite materials tested can provide beneficial sealant, spall prevention, or roof stability control attributes for underground mining environments when applied by an experienced crew using a well-maintained gun, in accordance with product manufacturers' recommendations and when used for the designated purpose.

Jan 1, 1984