Search Documents

By d&apos, Kathleen J. Amico

THIS summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S mineral production also is included.

Jan 1, 1964

By N. N. Moebs

The Bureau of Mines air-sealed a 77-acre) above-drainage coal mine to evaluate sealing as a means of reducing the acid and metallic salt contents in drainage from abandoned mines. An approximate reduction in acidity of 150 ppm (equivalent to 193 pounds per day) and in iron of 98 ppm were directly attributed to sealing. The topographical, hydrological, and other factors involved in air-sealing are discussed, and the construction used to seal the mine is described.

Jan 1, 1970

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

By Robert J. Timko, Edward D. Thimons

Sulfur hexafluoride (SF6) is an odorless, colorless, nontoxic gas that has found acceptance as a tracer gas in research on ventilation pat- terns, measurement of air leak rates, respirable dust reductions due to bagging hood modifications, and the study of airflows relating to gob boreholes. Following a short review of the SF6 sampling technique, this report describes recent Bureau of Mines projects in which SF6 was used successfully as a tracer gas, enabling researchers to acquire representative data quickly and inexpensively.

Jan 1, 1982

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

By J. R. Thoenen

[Since the publication of the preliminary report on this subject in July, 1927, (The Wire Saw in Slate Quarrying, Preliminary Report, Serial No. 2820, by Oliver Bowles) the wire saw has been in constant daily operation at the quarry of the Colonial Slate Company. Luring this time between twenty end thirty successful cuts have been made varying in length from forty-five to ninety-two feet and in depth from six to ten feet. No accurate time records have been kept on these cuts but they have totaled over 12,000 sq. ft. of area and required 19,000 lineal fact During these cuts the average speed of cutting has risen from the 12.8 sq. ft. per hour obtained in the original recorded tests to between 15 and 20 sq. ft. per hour, with the present rate running very close to 20 sq. ft. per hour at this quarry.]

Jan 1, 1928

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976

By Raymond B. Ladoo

Cne of t·: . .:: i::,portt recent developrr.ents in the feldspar industcy l:.a.s beer. tl:.e r,:ipid. rise of Ne·N H.v-:psr.ire as a. feldspar producing State. Tl:.e unusual size and purity of t: e deposit now 'being worked ne3.r Keene, and tr.a i.nproved metl:.ods ot:' rr.ining srd ir,illing used l:.ave been responsible foe tt.is situation. ti'eldsp'.:l. w'ls occ':tsiona.lly produced sorr.e ye1rs ago in srr.a.ll (tuantities in New Hrunpshi :e, but t::.e State had not been considered a producer of" feldspar ui til lS3l. In the s::ring of tr .. at yea!', t:.e '[eane iic Products co. of Keene, N.H., beg3Il in a srr.9.ll way tl:e production of feldspar fro:n t1eir property in Gilsum, H.H., whicr. l-.a.d long been opera.tei a.s a :tl.ca mine. The purity of the feldspar at enoe '\ttracted f''.lvorai)le attention. and tt.e production of crude ore rapidly in­ cre'.\sed. Early in 1922, a new company, t'he Golding-Keene Co,

Sep 1, 1922

By R. D. Leitch

The pollution of streams by acid mine drainage has become of great importance in the past few years in certain regions of the United States. Large quantities of acids are used in a discharged from other industries than mining, notably in tube, sheet, tin-plate and era hell inn works. These are usually less important then coal mines as a source of acid drainage, because of their more limited distribution throughout the States most affected by acid waters and their relatively smaller numbers. Streams are naturally alkaline and are, therefore, able to take care of rather large quantities of acid wastes, but when such enormous quantities as are often found in mining districts enter the streams, the natural alkalinity is quickly overcome. When a neutral or almost neutral condition has been reached, the further addition of a relatively slight quantity of acids will cause a great difference in the quality of the water.

Jan 1, 1926

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By J. J. Demeter

Anthracite from the four producing regions in Pennsylvania was both ashed in the laboratory and burned on a chain-grate stoker to determine the sulfur-retention properties of its ash. The retention of sulfur in laboratory-prepared anthracite ash was shown to be related to ashing temperature and to the amounts of sulfur and calcium present in the coal. At the usual laboratory ashing temperature of 750° C sulfur retention ranged from 0.8 to 13.2 percent of the total coal sulfur. Sulfur retention in the ash was negligible, o to 0.3 percent, at 1,200° C, which is the thermal decomposition temperature of calcium sulfate; thus calcium sulfate does not form and cannot serve as a sulfur-retaining agent. In several tests the anthracite was mixed with 6 or 10 percent dolomite prior to firing in the chain-grate stoker. The dolomite did not improve sulfur retention owing to the high temperature in the fuel bed. Sulfur retention was, however, related to the unburned carbon in the ash. The relationship of the percentage of original coal sulfur retained in the ash (Y) to the percentage of the original carbon in the coal remaining in the ash (X) is expressed by Y = -0.579 + 0.914X. The percentage of sulfur retained is almost directly proportionate to the percentage of original coal carbon in the ash.

Jan 1, 1968

By D. S. Burgess

The characteristics of gas-phase detonations were observed in 20 instrumented firings within earthen tunnels, in 100 such detonations in a 24-in-diam by l63-ft-long steel pipe, and in about 200 smaller scale firings. Most of the fuels studied were representative hydrocarbons--acetylene, propane, gasoline, and a roughly equimolar mixture of methylacetylene, propadiene, and propane. In a pipe with two closed ends, the detonable limits were demonstrated to be very nearly the same as reported limits of flammability. The side-on impulses (pressures integrated over 200-msec intervals) were shown to be the same function of concentration regardless of whether deflagration or detonation had occurred. In a pipe with only the initiation end closed, the impulses of all fuel-air systems tended toward the same level when averaged over comparable ranges of fuel concentration; the lower pressures with saturated hydrocarbons were nearly compensated by longer durations of pressure transient. In all fuel-air systems, unexpectedly high impulses were obtained with slightly lean mixtures. In earthen confining structures, the impulse, of the explosion was efficiently converted into momentum of the failing wall. In the configurations studied, an earth velocity of about 20 fps was critical to overcome the soil's resistance to shear. The destructive effect was determined by gas pressure rather than by total energy release. The assignment of a "TNT equivalent" to an explosive gas mixture is discussed in terms of the confinement of the mixture.

Jan 1, 1968

By D. R. Tesarik, R. W. McKibbin

Material properties affecting slope stability were measured in a large 50-year-old, partially consolidated rockdump located in an active open-pit mine. Field tests included single-ring infiltration and density. In addition, a nuclear depth-moisture gauge was used to measure water content in six stainless-steel-cased drill holes on the crest and an upper bench of the rock dump. Precipitation, evaporation, wind speed and direction, and temperature data were collected at a weather station installed on the dump’s crest. Laboratory tests included particle-size distribution, specific gravity, Atterberg limits, and water content. By measuring material properties of a rock dump presumed to be stable, the safety of miners working on or at the toe of old rock dumps constructed of similar material and located in a similar climate can be assessed.

Jan 1, 1999

By M. J. Ackerman, C. R. Waine, W. M. Merritts, L. P. Mokwa

Tests were conducted in the Pocahontas No. 4 coalbed in southern West Virginia to determine if successful degasification techniques, developed during an earlier study in the Pittsburgh coalbed, would be effective in removing methane from those usually more gaseous coals. Specially designed long-hole drilling equipment and Bureau of Mines continuous recording devices were used to measure the quantity and methane content of the ventilating air during the investigation. Infusions were made with water at normal waterline pressures ranging from 200 to 220 psi or at pump pressures ranging from 400 to 650 psi. Results of the tests showed that methane emissions from free-flow bleeder holes were as much as 131 cfm. Infusions of some of the holes increased the methane emission from other holes and from the exposed coal surfaces near the working areas as much as 1,540 cfm. The methane content in the main return-air currents after infusion was reduced more than 86 percent of the amount recorded before tests were made.

Jan 1, 1963

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

By Maria I. De Rosa

This report analyzes mobile equipment fires for all U.S. surface and underground coal and metal/nonmetal mining categories by state and 2 year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from MSHA mine fire accident publications and verbal communications with mine personnel. The analyses will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the hazards associated with mobile equipment fires and will create a basis for future fire research programs.

Jan 1, 2004

By William J. Wiehagen

This is the third in a series of four articles that discuss underground fire-fighting preparedness. As with the first two articles, it is based on interviews with 214 miners conducted at 7 underground coal mines (referred to as Mines ?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996]. In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. In this article, we describe miners? experience in fighting underground mine fires and present their perceptions of training and readiness for fire-fighting.

Jan 1, 1997