Search Documents

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Nicholas County, W. Va. It is one in a series describing coals suitable for producing metallurgical coke, either as mined or after beneficiation. Almost 5 million tons of coal were produced in Nicholas County, W. Va., in 1960, of which over 2.6 million tons were cleaned in eight preparation plants. It has been estimated that over 6 billion tons remained in the county as of December 31, 1960, in beds 12 inches and more thick.

Jan 1, 1962

By Maria I. De Rosa

Table 55 and figure 19 show the number of fires and fire injuries for stone mills by state during 1990-2001. Table 55 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 118 fires occurred in 33 states. Seventy-six of the fires caused 82 injuries (including 8 fires and 6 injuries involving contractors). The yearly average was 9.8 fires and 6.8 injuries. The Ewhr value was 873 x 106 hr (In = 0.019), and the LWD value was 1,911. Missouri had the most fires (16 fires and 9 injuries), followed by Pennsylvania (15 fires and 14 injuries), Michigan (9 fires and 5 injuries), and Virginia (7 fires and 5 injuries). Of these states, Virginia had the highest injury risk rate value (In = 0.09 1). Table 56, partly illustrated in figure 20, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries decreased during most of the periods, with a sharp increase during the last period. The number of employees' working hours increased throughout the periods. The In values follow patterns similar to those shown by the injury values. Tables 57-63 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 21 shows the major variables related to fires for 1990-2001. Table 63 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

By Ronald D. Hill, Elmore C. Grim

The removal of overburden often exposes pyritic materials (iron disulfide). As shown in equations 1 and 2, the oxidation of this material results in the production of ferrous iron and sulfuric acid. The reaction then proceeds to form ferric hydroxide and more acid, as shown in equations 2 and 4. [ ] Consequently a low pH water is produced (pH 2-4.5). At these pH levels, the heavy metals such as iron, manganese, copper, and zinc are more soluble and enter into the solution to further pollute the water. Water of this type supports only limited water flora, such as acid-tolerant molds and algae; it will not support fish life, destroys and corrodes metal piers, culverts, barges, etc., increases the cost of water treatment for power plants and municipal water supplies, and leaves the water unacceptable for recreational uses. The amount, and rate of acid formation, and the quality of water discharged are a function of the amount and type of pyrite in the overburden and coal, time of exposure, characteristics of the overburden, and amount of available water(l). Crystalline forms of pyritic material are less subject to weathering and oxidation than amorphic forms. Since oxidation by oxygen is the primary reaction during early acid formation, the less time pyritic material is exposed to air, the less acid is formed. Thus, a positive preventative method is to cover pyritic materials as soon as possible with earth, which serves as an oxygen barrier. In terms of mining, this step is accomplished by current reclamation techniques and small open pits.

Jan 1, 1974

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 40 ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 40 ft.

Jan 1, 1992

By Robert E. Johnson

THE MILDEST recession of the postwar period ended in the first months of 1961, and the economy climbed steadily during the remainder of the year. The Federal Reserve Board (FRB) Index of Industrial Production climbed from a low point of 102 (1957=100) in February to 115 in December, a rise of 12.5 percent. But economic activity for the year as a whole was only 1.5 percent higher than the 1960 level, as measured by real gross national product (GNP). Although activity increased throughout 1961, much of it was merely regaining ground lost in the decline during the second half of 1960 and the first months of 1961. The FRB index did not re ain the July 1960 high of 110 until June of 1961. Mineral fuels did not fully share in the economic recovery. The (FRB) crude oil and natural gas index rose only 5 percent between February and December. Although the index of monthly coal production increased 11.5 percent during the year, the February level was so low that total production for the year was the lowest since 1954. Total production of energy measured in Btu's was up slightly (1 percent) during the ear. Coal production was down; production of crude oil and natural gas was up. Calculated consumption paralleled production-total up slightly, coal lower, and crude oil and natural gas higher. The most interesting product developments were in coke and residual fuel oil. Sales of coke showed a sharper drop than steel

Jan 1, 1962

By Warren E. Morrison

The continuing high-level performance of the domestic mineral and mineral fuels industries during 1966 was sustained by the longest business upturn in the Nation's history. Spurred by consumer demand at home and the defense production requirements of the Viet-Nam war, the rising trend of economic activity during the year was reflected in the upward movements of the major economic indicators. At yearend the gross national product (GNP), representing the value of all goods and services produced, stood at $740 billion, $58 billion greater than in 1965. Corrected for price changes, the real value of GNP in terms of 1958 dollars was $648 billion and represented an annual increase in economic activity of 5.4 percent. Some 74 million persons were employed during the year out of a total population of 196.8 million, while unemployment fell below 4 percent. The Federal Reserve Index of Industrial Production averaged 156 for 1966, up 13 points from the previous year. However a jarring note in the 1966 expansion, and one which affected the mineral industries in particular, was the increasing pressure on prices and the threat of inflation. From 1961-65 economic growth was facilitated by relatively stable wages and prices and only mild inflation. During the period average wholesale prices hardly moved while average consumer prices rose only about I percent per year. But this long run of relative price stability ended during 1966 when consumer prices rose 2.9 percent and wholesale prices were up 3.2 percent from the previous year.

Jan 1, 1967

By Eliot J. White

The physical properties and clay mineral content of the major oil-producing formations in the Powder River Basin of Wyoming were determined by analyses of cores from 100 wells. Interrelationships were established among permeability, restored water saturation, clay content, and bulk swelling capacity of the crushed sample and used to estimate the susceptibility of the formations to water damage. The ratio of water permeability to gas permeability (kw/ki) offers a convenient scale for semiquantitatively estimating the water sensitivity of sands. The irreducible water saturation was also found to have a similar relationship to the clay mineral content and the water sensitivity of the sands. The average relation of water permeability to gas permeability is different for each sand, as shown by the curves, and the relative positions of the curves indicate the degree of water sensitivity of each sand from which the susceptibility to water damage may be estimated. How accurately these estimates show formation behavior under field operations will not be known until studies of field performance can be made. The water permeabilities of the Muddy, Minnelusa, and Tensleep sands average about the same as the gas permeabilities, and these sands are classified as insensitive. The water permeabilities of the Sussex and Shannon sands, at the other extreme, are much less than the gas permabilities [when average ki is 30 millidarcys (md), kw is 6.1 md], and these sands are classified as highly water sensitive. The sensitivities of the five other sands are between these extremes.

Jan 1, 1962

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

UNIT OF MEASURE ABBREVIATIONS USED IN MFIRE FT foot FT3/MIN cubic foot per minute LBM•MIN2/FT4 pound mass times minutes squared over feet to the fourth FT2/HR square feet per hour BTU/HR*FT*F British thermal unit divided by hours times fimes feet times degree Fahrenheit IN W G inches water gage FT3/MIN cubic feet per minute FT2 square feet FT3 cubic feet LBM, pound mass F Fahrenheit IN W G /CFM2 inches water gage per cubic foot per minute squared PERCENTAGE percent BTU/MIN British thermal unit per minute MFIRE BAT PROGRAM cls echo off echo MFIRE activated mfire0 echo Wait a moment for loading the program if EXIST zheng chg mfirel if EXIST zheng chg mfire2 if EXIST zheng chg mfire1 if EXIST zheng chg erase zheng chg if EXIST hang chg erase hang chg if EXIST yunzhi fan copy yaodong.ion+yunzhi fan yaodong ion if EXIST yunzhi fan erase yunzhi fan if EXIST xintan chg copy yaodong xin+xintan chg yaodong ion if EXIST xintan chg erase xintan chg if EXIST yaodong xin copy yaodong.xin mfire out if EXIST yaodong.xin erase yaodong.xin if EXIST net erase net echo Your output is saved in file MFIRE OUT MFIRE0 FOR PROGRAM CHARACTER•50 A OPEN (10,FILE='NET',STATUS='UNKNOWN',FORM='UNFORMATTED') NETWW=0 WRITE (10) NETWW OPEN (21,FILE='ZHENG CHG',STATUS='UNKNOWN',FORM='UNFORMATTED') A=) ' B=0.0 WRITE (21) A WRITE (21) A,B

Jan 1, 1990

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the fifteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by halt townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 halt-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The Descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned & name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled except the deep holes drilled to test geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Erie C. Donaldson

Gas-displacement tests were made in Berea Sandstone and Arbuckle Lime-stone cores to determine the relative permeabilities to gas, oil, and water for two-and three-phase dynamic systems. Three-phase relative permeabilities were obtained by displacing oil and water from the core with gas and measuring the flow rates of the three fluids simultaneously. It was found that relative permeabilities to fluids in a porous medium are affected by the saturation distributions of other fluids in the medium as well as by their own saturation distributions.

Jan 1, 1966

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By G. W. Jones

Phthalic anhydride is a solid having the formula C8H4O3. It is an important intermediary in production of anthraquinene, alkyd reins, and plasticizers. The combined annual production of phthalic anhydride reported by 10 major manufacturers for 112,250 tons. The raw materials in the manufacture of phthalic anhydride have been the source of numerous fires and explosions. Consequently, the need was felt to determine the temperature flammability and the ignition temperatures crude basic raw material in most phthalic anhydride production crude phthalic anhydride, and pure phthalic anhydride.

Jan 1, 1950

By W. H. Pailes, V. Castranova, D. Lewis, G. Goodman

We performed bronchoscopy with bronchoalveolar lavage (BAL) in 8 control subjects with no exposure to occupational dusts, 8 healthy power plant workers exposed to mixed dusts (primarily fly ash), 1 healthy coal miner and 1 rock driller with acute silicosis. All subjects were non-smoking males. We analyzed lavage effluents for total numbers of alveolar macrophages, lymphocytes and neutrophils and monitored chemiluminescence at rest (REST CL) and after stimulation with 3x10- M phorbol-12-myristate-13-acetate (PMA CL) or 2 mg/ml zymosan (ZYM CL). The data are as follows:

Jan 1, 1988

By Hans M. Cassel

The specific objective of research presented in this report was clarifi- cation of physicochemical fundamentals of the mechanism of dust explosions. The equipment, techniques (chiefly photographic), and dusts (chiefly graphite and light metals) employed are described. From behavior of individual par- ticles, conclusions are drawn as to their cooperative function in ignition and combustion of dust clouds. Results are interpreted using thermal theory as accepted for combustible gas mixtures. Radiative transfer across the flame front, as a characteristic of dust flames, is given particular atten- tion. Related studies by other investigators are discussed.

Jan 1, 1964

By I. AITKENS

Tourmalines are among the most beautiful of all the semiprecious stones, and are unsurpassed even by corundum in variety of hue. The stones most suited to jewelry purposes are those comparatively free from iron. One reason for the fact that the tourmaline has advanced rapidly in public favor in this country is that it is found in California in great profusion and of extraordinary quality. The superb green and especially the pink crystals found at Pala and Mesa Grande in San Diego County, Calif., are deemed superior to tourmalines from all other localities.

Nov 1, 1931