Search Documents

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By Spencer P. Howell, J. F. Xrawshaw

"A recent premature explosion in a quarry that resulted in the death of nine men and the injury of several others, was directly traceable to a spark from a steam-shovel working under the face directly in front of the hole being loaded. This accident and similar accidents on record in the Bureau of Mines indicates the necessity for pointing out the dangers in quarries of explosives being ignited by sparks emitted from steam shovels and locomotives, and making recommendations for greater safety.Many premature explosions of which the following are examples, have resulted from sparks, both from steam shovels and passing locomotives. (A) The premature explosion occurred during August, 1920 at a limestone quarry, in a 100-foot drill hole, loaded with 1000 pounds of high-grade nitroglycerin and gelatin dynamites. This hole had been loaded with 500 pounds of 75 per cent strength gelatin dynamite, 300 pounds of 60 per cent straight nitroglycerin dynamite, and 200 pounds of 50 per cent straight nitro¬glycerin dynamite; but no steaming had been placed in the hole. The powderman loading the hole saw the spark enter the hole and was able to run a short distance before the explosion took place, thus escaping serious injury. The explosion of this first hole was transmitted to nearby hole similarly charged. The fall of rocks from these two holes buried the steam shovel and some of the gang of men working around it.(B) In September, 1909, in the Canal Zone, a steam shovel uncovered a misfired charge of dynamite. While the dynamite was being picked up the steam shovel continued working nearby. A spark from the shovel set fire to some loose dynamite spilled on the ground from the troken cartridges. This fire was transmitted to a hole which was being loaded close by and caused a premature explosion. One man was injured."

Nov 1, 1920

By R. K. Franklin, S. T. Reese, J. J. Forbes

"INTRODUCTION It is a recognized fact that in the coal-mining industry coal dust must be allayed to promote the safety and health of underground workers. The Bureau of Mines has been cognizant of the hazards of coal dust for many years, and the necessity of controlling such dust was acknowledged when the Federal Mine Safety Code was formulated. Accumulations of coal dust increase the explosion hazard in a bituminous-coal mine and facilitate the propagation of an explosion. Some of the coal dust produced in mining is inhaled by the workers and contributes to respiratory infection. Impairment of vision and personal discomfort resulting from working in dense clouds of coal dust reflect unfavorably on the efficiency of workmen. Considerable coal dust, originating at the working face, is carried in the ventilating current and deposited elsewhere in the mine, thereby increasing the explosion hazard. It is apparent, therefore, that if coal dust could be allayed effectively at its points of origin, the dust-explosion hazard in bituminous-coal mines would be reduced greatly.Although dust control is practiced in many bituminous-coal and lignite mines, the extent and effectiveness of control for the, entire industry-is not generally known. The purpose of this circular is to present such information clearly, and to encourage coal-mine operators to install dust- allaying equipment.Factual data on dust-allaying practices at working faces in a large number of the bituminous-coal and lignite mines in the United States were .compiled from reports on recent Federal inspections of these mines, The information is presented in tabular form to permit review of the dust-allaying practices of a substantial part of the industry, by States, and also according to employment, and loading practice."

May 1, 1950

By J. W. Pall

The method of mining bituminous coal in Pennsylvania cannot be treated in an extended manner in this publication since this would require more space than justified. The general plan of operation of most mines is on the room and pillar system, using double entries from which the rooms are driven In the early mining in the Pittsburgh coal bed the "checkerboard" plan was much used, but this entailed a large loss of coal in the blocks of coal that were left standing. In recent years there has been a tendency towards the adoptions of the panel, room and pillar method, also the block system, which ad mats of concentrated mining within a relatively small section of the mine It is not unusual to use 4, 6, or 8 parallel entries for the panel development. The longwall advancing method has been tried in some of the thin beds of the central coal field, but so far it has not passed beyond the experimental stage. The average extraction' of coal throughout the State is 714 per cent, but it is estimated that 15 5 per cent of the loss is avoidable, so the actual extraction should approximate 87 per cent. Pennsylvania is exceptionally well provided with means of transportation by trunk lines, branches, and by intra State railroads, among which are the Pennsylvania, Baltimore & Ohio, New York Central, Buffalo, Rochester & Pittsburgh, Western Maryland, Bessemer & Lake Erie, Pittsburgh & West Virginia, Pittsburgh & Lake Erie, Erie, Monongahela Division, and Montour railroads, all of which reach some of the bituminous mines The Monongahela River furnishes water transportation for Allegheny, Greene, Fayette, and Washington counties During 1923 the coal traffic on this river amounted to 18,709,084 tons, and of coke, 385,426 tons Coal is moved on the Allegheny River also, the total in 1923 being 911,178 tons s.

Jan 1, 1928

By Robert L. Chufo

The paper, "An Electromagnetic Roof and Rib Thickness Sensor" presented at The 12th WVU International Mining Electrotechnology Conference in 1992, presented the results of roof coal thickness measurements in underground mines and rib coal thickness measurements in highwall mines. The microwave sensor described uses a unique spatial modulation scheme created by antenna motion, along with frequency domain signal processing, to solve the problem of media, target, and antenna dispersion. This paper further describes the advantages of the unique frequency domain signal processing technology chosen by the U.S. Bureau of Mines in extending previously reported one-dimensional thickness measurement technology to the generation of a full three-dimensional underground image of the underground environment. The electromagnetic signature of a media, whether it is coal or other geological material, is its permeability and permittivity and the effect on the velocity and amplitude of an electromagnetic wave as it passes through. High-quality imaging cannot occur without the identification of, and correction for, the permittivity and permeability of each layer of a multilayer geological deposit. Clutter, or any signal that can interfere with target discrimination, usually comes from objects in the field of view for which there is no design control. These are nuisance targets with possibly very high contrasts compared to the real target. The only proven tool to reduce clutter is to increase spatial, spectral, and polarization diversity. This paper will describe some techniques being used by the U.S. Bureau of Mines to increase the information content of both single-dimensional and three-dimensional imaging systems through the identification of media distortion mechanisms made possible by the use of spatial/spectral sensor technology. These techniques will permit high quality imaging in an environment where the data is corrupted by dispersion and clutter.

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for coal preparation plants by state during 1990-1999. Table 28 also shows the risk rates, employees' working hours, and lost workdays by state. For coal preparation plants, 91 fires occurred in 1 1 states during 1990- 1999. Twenty-three of those fires caused 25 injuries (the yearly average was 9.1 fires and 2.5 injuries). Ten fires and eight injuries involved contractors. The Ewhr value was 24 1 x 10' hr (Irr = 0.02 l), and the LWD value was 198. Pennsylvania had the most fires (24 fires and 4 injuries), whereas West Virginia (22 fires and 7 injuries) and Kentucky (22 fires and 7 injuries) had the most fire injuries. Among these states, Kentucky had the highest injury risk rate value (Irr = 0.025). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the periods (an increase is seen only during the last period). The number of fire injuries show a decrease followed by an increase during the periods, accompanied by a decline in employees' working hours throughout the periods. The Irr values follow patterns similar to those shown by the injury values (see table 29 and figure 11). Tables 30-35 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 12 shows the major variables during 1990-1999. Table 36 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By E. D. Gardner

"It has only been in recent years that the proper ventilation of metal mires has received serious consideration. Increasing temperature and humidity with greater depth in some of the larger mines of the West prevented the efficient operation of the mines and made the installation of mechanical ventilation systems necessary. Doors that interfere with tramming are generally needed to control properly the mechanically induced air currents and are one of the inherent disadvantages of the system. In fact the necessity for the use of doors in the main haulageways has discouraged the installation of mechanical ventilation in some metal mines.A number of mining companies in Arizona are using ventilation doors which can be opened and shut mechanically by the motorman without leaving his seat or stopping his train, end thus interfere very little with the transportation of the ore. The Copper Queen Branch of the Phelps-Dodge Corporation at Bisbee introduced these ventilation doors and adapted them from those in use in the company's coal mine at Dawson, New Mexico. Other mining companies have installed the same type of door and it is now being used in a number of districts in Arizona.The doors at the Calumet and Arizona mine in the Bisbee district are representative of those in use. The doors at this mine are substantially built of 2-inch lumber, are air tight, are well placed and have two openings or passageways. The main door, which is used for the motor trains, is 5 feet wide by 6 feet high and is opened by compressed air and closed by a counterweight. At the side of the motor door is the man door, which is 16 inches wide by 5 feet high and is opened and closed by hand."

Aug 1, 1921

To develop a quick, safe, and effective method that allows workers at mineral processing operations to clean their dust-soiled clothing periodically throughout the workday. Background Reducing workers' respirable dust exposure to silica and other harmful dusts and contaminants is an ongoing goal in the U.S. mining industry. One area of known worker exposure is from contaminated work clothes. A U.S. Bureau of Mines report documented a number of cases where a tenfold increase in a worker's dust exposure was measured from contaminated work clothes. In these cases, the dust emitted from clothing caused the worker's dust exposure to exceed the permissible exposure limit in less than 2 hours. The most effective way to eliminate this dust source is to have workers clean or change their work clothes. There are two federal regulations that impact the clothes-cleaning process. The first states that at no time shall compressed air be directed toward a person, but that when compressed air is used, then all necessary precautions shall be taken to protect persons from injury. The second regulation states that compressed air should only be used for cleaning purposes when it is less than 30 psi and used along with personal protective equipment. For the mining industry, by default, the only approved method to perform clothes cleaning is to have workers vacuum their clothes using a HEPA filter system. This is very difficult and time-consuming and, in most instances, not very effective. Most workers would prefer to use a single compressed air hose to blow dust from their work clothes. However, not only is this method prohibited by law, it usually creates a significant dust cloud in the work environment and contaminates coworkers.

May 1, 2005

Develop a method to evaluate the effectiveness of coal scam fire surface seals so that potential problems may be corrected at an early stage, before the integrity of the surface seal is lost. Background Surface seals are the primary coal seam fire abatement method being used in the western United States. Surface seals smother a fire by denying it oxygen. The seal is usually constructed by placing a mantle of soil, four to ton feet thick, over a coal scam fire area to exclude air from the fire. The soil is compacted to increase effectiveness, and a soil cement may be used to augment the soil. In some cases, burning coal may be excavated and separately smothered or otherwise extinguished in another area; in other cases, a trench maybe excavated and backfilled with incombustible material to isolate a fire. More often, a surface seal is simply applied over and around the entire known burning area. In the 1950's, the Bureau of Mines administered a large program to treat numerous coal seam Fires across the western United States. Methods used in this program were described in Bureau of Mines Information Circular (IC) 7932, dated 1959. More recently however, various coal seam fires have been treated with surface seals under the direction of state Abandoned Mine Land Reclamation authorities. It has frequently taken years to evaluate the effectiveness of surface seals. By the time problems become evident, it has often been too late to take corrective action within the scope of the original abatement project. For this reason, the Bureau of Mines developed a means for tracking temperature trends at coal seam fire projects to obtain a better and earlier handle on the effectiveness of surface seals.

Jan 1, 1991

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

By R. W. Stahl

One of the broad purposes of the Bureau of' Mines since its establishment has been conservation of mineral resources. As some of the coal beds approach depletion, especially those coals suitable for making metallurgical coke, more and more attention is being given to means of recovering a larger percentage of coal in place. The customary system of mining in the United States is by room and pillar, or some variation thereof, which leaves pillars of coal to support, the roof. In many operations, where the pillars are not systematically recovered, the loss of coal often amounts to 50 percent or more of the original deposit. In many instances in developing new mines, It is planned to recover chain and barrier pillars on retreat when the mine has reached established boundaries. Too often, however, mines are abandoned for some unforeseen reason before completion of mining without recovering any pillars. Usually, these pillars are lost forever. With this in mind, the Mining Division, Region VIII, of the Bureau; of Mines is encouraging mining by longwall methods. It is a generally known fact that almost all of the European coal is mined by longwall methods, which are conducive to a high percentage recovery of coal. A comparison between mining systems usually is on the basis of tons per man per shift. Unless all operating conditions are similar, such a comparison could be misleading. Generally, the output per man shift in European longwall mines is less than that obtained in room-and-pillar mining in the United States. In European mining, maximum recovery of coal is not only mandatory but it must be accomplished without major damage to surface by subsidence. These restrictions necessitate packing or stowing with consequential increases In manpower and decreases in output per man shift.

Jan 1, 1954

By G. M. Potter, F. S. Wartman, M. D. Schmid

"In matte smelting of copper it has been established that the sulphpr present will combine with copper as long as the latter is present, and that thereafter it will combine with iron. The Cu-Fe ratio in the matte is determined by the Cu-S ratio, presumably owing to the much greater affinity of copper for sulphur or, expressed thermodynamically, the greater stability of copper sulphide in contact with silicate slag. Now, the work of Fournet and of Schütz, which is quoted in many elementary metallurgical texts, indicates that manganese ranks ahead of copper in its affinity for sulphur. Hence, we might expect that manganese could be concentrated from its admixture with iron. Compounds by matte smelting, and Rotts / has patented such a process. This greater affinity of manganese or sulphur is used to advantage in iron metallurgy, also, in which it is well-known that sulphur will combine with manganese and separate from metallic iron as manganese sulphide. Manganese sulphide,however, is quite soluble in silicate slags. 5/ The loss of manganese in slag in any attempted matte smelting is therefore great.If this solubility of manganese sulphide is slag is a physical one and the reaction MnO + FeS MnS + FeOIs substantially complete, then it might be expected that the addition of copper sulphide, which is almost entirety insoluble in slag, would serve to extract the manganese sulphide with the formation of a manganese-copper matte on the other hand, if an equilibrium exists in the above reaction, a copper sulphide layer would displace that equilibrium in one direction or the other, according to whether iron sulphide or manganese sulphide were more soluble in the matter layer."

May 1, 1937

By J. T. Schimmel

The purpose of this investigation was to obtain complete information on some of the uses of a 24-inch-diameter auger in the underground mining of pitching anthracite beds. The auger was placed in operation early in 1958 to drive ventilation connections between coal gangways driven by a continuous miner. Although designed to drill rise holes only, it was used also to drill dip holes. The latter holes were drill id from an adjacent gangway to avoid interference between the auger and the continuous miner. These holes established immediate ventilation returns when intersected by the continuous miner. Bureau participation in the project covered 361 working days. The auger was used on 288 shifts, usually one 7-hour shift per day, and drilled 3,246 feet, of which 493 feet were reamed. The longest hole was 87 feet; hence the maximum drilling depth of the machine (rated at 100 feet) was not required. Holes drilled normal to the strike of the bed ranged from 30 to 66 feet deep, averaging 45 feet. The continuous miner drove gangways on 575 shifts. Thus, the auger worked one shift for each two worked by the continuous miner and was used on less than 80 percent of the workdays. The auger drove 24-inch holes 10 times faster than the larger, conventional openings could have been driven by usual mining methods and exceeded the workload for which it was purchased. Augering eliminates exposure to the hazards encountered in driving chute-work by conventional methods and provides adequate circular ventilation openings, which are strong in self support and are adaptable to reaming when required. With alterations, the auger may have limited use as a production machine in thin-bed pitch mining but cannot compete with established methods of thick-bed pitch mining.

Jan 1, 1962

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

By Lester G. Morrell

While developments in Australia dominated the minerals industry of the South Pacific area, New Caledonia's nickel, manganese ore from New Hebrides, gold from Fiji and New Guinea, and phosphate rock from several small islands were significant in world supplies of those materials. The total value of mineral commodities produced in this area in 1965 has been estimated at about $763 million an increase of nearly 16 percent over the value reported in 1964. Increases were recorded in mineral production value with respect to that of 1964 for all of the countries except Papua-New Guinea where lower gold output resulted in a drop of about $300,000 and in the several phosphate-producing islands that collectively recorded a value decline of around $1.3 million. Exploration and development activities continued at an intensified level, not only in Australia and New Zealand but also in the British Solomons, Bougainville, and Fiji. Substantial additions to world supplies of iron ore and bauxite are assured and recent discoveries of natural gas, manganese ore, and nickel combine to give Australia a brilliant mineral outlook. Important discoveries of copper on Bougainville Island and on Vanua Levu, the north island of the Fiji group, and a gold mine on Misma Island were being developed during the year, with plans for early production underway. In New Zealand progress has been made on the New Zealand Steel Company project, and preliminary appraisal of a new titano-magnetite beach sand resource on the South Island has aroused considerable industrial interest. Extensive geophysical investigations were carried out in the British Solomon Islands and on Fiji's goldfields. The expansion program that will double output of products by New Caledonia's Société Le Nickel continued through 1965, and several foreign private companies have expressed a desire to initiate additional industries based on nickel prospects in New Caledonia.

Jan 1, 1967

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976