Search Documents

By C. Kwong, L. H. Rorden, T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating, boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±15% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Ti tan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 5, 1978

By Barbee J. Scheibner

This Bureau of Mines report describes the geology and physical properties of core samples at the Sunnyside coal mine No. 1, Sunnyside, Utah, and was written in conjunction with the Single-Entry Program conducted at the mine. The objective of this program was to test the hypothesis that the single-entry system in the Sunnyside mine, supported in the center by open cribs and divided by a fire-resistant partition, is equivalent to or better than a two-entry sys-tem. Drill cores, taken underground at 15 sites in the single-entry study area, facilitated the construction of geologic cross sections of the entries. Physical property data obtained from the drill cores was used in a three-dimensional finite element analysis program to evaluate the stability of the openings, the support requirements, and the de formation characteristics of the roof and floor material. Data on 10 physical property parameters for 5 rock types plus coal are also tabulated and discussed.

Jan 1, 1979

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

By Glenn C. Reed

"Preliminary examination of the Glass Buttes mercury deposits, Lake County, Oregon, was made in August 1945 at the request of W. S. Lazier, present lessee of the deposit.Most of the prospect openings in the area were inspected. The more significant workings were sampled and napped in detail. This report presents the data obtained from the investigation to date.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. noon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. P. S. Dean, assistant director.Special acknowledgment is due to S. H. Lorain, chief, Albany Division, Mining Branch and to S. R. Zimmerley, chief, Salt Lake City, Utah, Metallurgical Division, for analyses of the ores.The presence of quicksilver in the Glass Buttes district has been known since about 1930. The area immediately north of Middle Butte has been superficially prospected by numerous test pits, trenches, shafts, and short adits, which revealed a number of opalized zones. Many of these opalized zones contain weak to strong concentrations of cinnabar. The area has not boon explored thoroughly; no mercury has been produced from any of its deposits.A block of 48 full-size claims has been located to cover a large part of the area in sections 34 and 3, Tps. 23 and 24 S.,R. 23 E.,W.M. These claims, held by, location are owned by H. S. Miller, lumberman of Bend, Ore. W. S. Lazier, 10N. W. 20th Avenue, Portland, Ore., currently controls the property under,a nominal leasing agreement. J. W. McDaniel, 44 Lake Place, Bend, Ore., has done much of the underground and surface exploration on the property.The Glass Buttes district is an area of low relief in the Deschutes River drainage system near the northeast corner of Lake County, Ore. (See fig. 1.) The arid climate is marked by extremes of winter and summer temperature. Water for cane use is not available in the immediate area. Well water, however, can be obtained in limited supply on ranch property 5 miles to the south."

Aug 1, 1946

By D. Harrington, C. W. Owings

Each year at least one and in some years several explosions are reported as having resulted from firing of mudcapped shots in coal mines; undoubtedly a number of small or local explosions occur that are not reported; in addition there are numerous accidents, some of them fatal, attributable to this reprehensible blasting practice. It is surprising that so few explosions and other accidents from this cause occur since the practice of firing mudcapped, Even in gassy "adobe," "dobe," "sand blast," or "bulldozed" shots is widespread. mines where general blasting is safeguarded by being done with permissible explo- sives, rocks or bowlders frequently are blasted with mudcapped shots of dynamite; even if permissible explosives are used, this type of shooting is dangerous. The usual method of preparing a mudcapped shot is to place the explosive, either in loose or cartridge form, with the detonator or "cap" on top of a piece of rock or coal and cover it with several handfuls of moist clay, loam, sand, or When the shot is road dust; in many cases there is no covering of any kind. fired a dense cloud of dust, together with an intensively hot fleme, are thrown into suspension, and if the dust is explosive or ignitable an explosion or igni- tion is likely to result practically simultaneously. The presence of gas greatly increases the explosibility of the dust, as well as the probability of an ignition. Every shot, of any known explosive, fired in a coal mine without having the charge properly confined in a drill hole and tamped with incombustible stemming to the collar of the hole, is capable of initiating an explosion that may cause the death of every man in the mine. Attention has recently been directed to this unsafe practice by an explo- sion resulting from a flagrant disregard of safe blasting practices in one of our The mine had been idle for several years most productive coal-mining regions. and was being prepared for reopening on a different system of mining. Six to 10 inches of bottom coal had been left in place during former mining operations, but in the new system it was felt desirable to remove the bottom coal left in certain parts of the mine. Instead of drilling holes in the coal, loading them, and fir- ing in the usual safe manner, five or six charges of dynamite were placed on top of the coal in each of several rooms; and while the men were at the mouth of the

Aug 1, 1929

By F. E. Cash

"In the interest of accident prevention it is felt that a report of the measures taken during the past four years toward the reduction of fatal accidents in Alabama, especially in preventing falls of roof and coal, will be of interest throughout the mining districts.In order to determine the primary factors in the reduction of fatal accidents from falls of roof and coal, the operators, State Inspection Department, and the Alabama council of the Holmes Safety Association were asked: ""What has your organization done to help in the reduction of accidents from fails of roof and coal?"" The responses to this question have made this report possible.To bring out briefly the reduction in fatal accidents from falls of roof and coal as well as from all causes, the following three tables have been prepared.These statistics have been compiled from the records of the State Inspection Department.In the order mentioned, it is felt that credit for the reduction in fatal accidents from falls of roof and coal should be given to the individual operating companies, the State Inspection Department, the Alabama council and chapters of the Holmes Safety Association, and the Alabama Mining Institute. The individual operating companies naturally head the list in that they are directly concerned from a humanitarian as well as a financial point of view. The State Inspection Department through frequent and thorough inspections and by providing necessary statistics is largely responsible for the reduction. The Alabama council and its affiliated chapters of the Joseph A. Holmes Safety Association through its publicity and education reaches a large number of employees throughout the mining district. The Alabama Mining Institute defrays the council expenses and thus makes possible much of this service to the Alabama mining industry.In 1925 there were 49 fatalities, equivalent to 115,169 man days per fatality, from falls of roof and coal, which was by no means a good record; in 1926 the number and frequency of accidents were reduced to 42 fatalities and 149,096 man days per fatality. When in 1927 the fatalities from this cause mounted to 61 and the man days per fatality were reduced to 89,903, it was quickly realized that more concentrated efforts must be exerted to reduce such accidents.As early as August, 1927, at which time the fatalities from falls had reached a total of 31, the following letter from the Chief Mine Inspector was written to each operating company in the State and was the initiation of a very strenuous campaign by all parties concerned towards the reduction of accidents from falls of roof and coal."

Nov 1, 1929

By R. D. Currie

"A million tons of coal mined in the Pennsylvania anthracite region without a fatality is a feat of which to be proud and one that deserves the commendation of the entire mining industry. The average production per fatality in this region for 1933 was 206,823 tons, an exceptional record showing the results of an intensive drive made by the Pennsylvania Department of Mines and the anthracite operators and-workers to curtail the high accident rates heretofore prevailing in the region.This paper gives information about a mine with a record five times better than the average which should prove to the industry that mine accidents can be reduced through the proper safety organization and effort. The Pine Hill Coal Co., managed by Weston Dodson & Co., Inc., and located at Minersville, Schuylkill County, Pa., has made such a record at its Oak all colliery by studying its accident experience, realizing the facts, and pursuing a definite safety policy with a view to bettering its accident occurrence.As a direct result of its safety policy this colliery has produced 1,044,000 tons of anthracite without a fatality; within 3 years it has reduced its total accidents from 645 to 105 per year, its compensable accidents from 204 to 45 per year, and its lost-time accidents from 335- to 67 per year. In addition, it has set up a smoothly functioning safety organization that will go fax in aiding in the continuance of this great work of mining anthracite at a lower .cost in human suffering.This circular describes the accident-prevention methods perfected and the results obtained by this colliery in the belief that similar methods will produce essentially similar results at any other colliery where they may be adopted.The writer acknowledges his indebtedness to the officials of the company who furnished him with the details of the safety organization and the data from which this report was prepared. He especially desires to thank Messrs. Stockett, general manager, Wells, general superintendent, Morgan, safety engineer, and Kistler,- statistical department, for their hind assistance.The mine is opened by shafts, slopes, and drifts, a characteristic of minas in the Southern anthracite field. Thirteen different beds of coal are being mined. The thickness of the beds ranges from 3.5 to 16 feet and the pitch from 0 to 900. The roof and floor exhibit the entire range of conditions found in anthracite mines. Table 1 describes the coal seams being worked."

Aug 1, 1934

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By Albert L. Toenges, Henry E. Dekay, James N. Scudder

Support of the immediate roof in coal mines is essential for their safe operation, and timbers are the most common means of support. Their effectiveness depends upon their resistance to decay. The theory has been advanced by some mine operators that rock dust, which is applied to ccal-mine workings to prevent propagation of explosions, accelerates the decay of mine timbers. As the results of part 1 of this study were inconclusive, the study was continued. Its principal objectives are: 1. To determine the effect of rock dusting upon decay of mine timber. 2. To compare the extent of decay of timbers in two mines in which underground conditions are similar. 3. To determine the loss in strength of the timbers after exposure to mine atmosphere. The studies were carried on in the Crucible mine of the Crucible Fuel Co. where the first part of this study was made, and in the Isabella mine of the Weirton Coal Co. The mines are on the Monongehela River and are adjacent.

May 1, 1943

By M. M. Fine

A laboratory mineral-dressing investigation of manganese ore from the Martin mine, Independence County, Ark., succeeded in recovering ferrograde manganese products. Sintered flotation concentrates analyzing 40.7 and 41.4 percent manganese at overall recoveries of 54.6 and 47.7 percent, respectively, were produced from preconcentrated feed, Preconcentration of the ore for flotation included treatment by magnetic separation and by a combination of magnetic separation and heavy-medium processing. The mineral-dressing study of the Martin mine rhodochrosite ore was part of a general program of the Bureau of Mines to develop domestic sources of strategic minerals, including manganese. Several such potential sources of manganese exist in the Batesville, Ark., district, one of which is represented by the Martin mine. Although the Martin mine area has not been delimited with respect to total reserve tonnage, it is considered to be one of the more important occurrences of manganese in the district. It is estimated that several 100,000 tons of manganese carbonate ore are present in this and similar properties.

Jan 1, 1954

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation 1 of a coal mine. The average thickness of coal seams mined in the United States decreased 2 inches between 1950 and 1955 to an average of 62 inches, which also is 3 inches less than the 65 inches in 1945. The decrease in thickness is due partly to the increased production from strip mines with thinner seams and partly to the increased percentage of total production at underground mines in certain States having thinner seams. The thickness of seams at auger mines was measured for the first time in 1955 and was 53 inches. Though bituminous coal and lignite is mined today from seams of exceedingly variable thickness -less than 2 feet to ore than 50 feet -a large majority of the production, 65 percent in 1955, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1957

By L. C. IlsLey

Figure 1 is a reproduction of a chart recently prepared by the Bureau of Mines at its Pittsburgh Laboratory to show the Bureau's approval work in connection with electrically operated mining equipment. Nearly 27 years of approval work, covering 346 approved units, are shown on this chart. These approvals are arranged according to year of approval and the manufacturer to whom approval was granted. Forty-five manufacturers are represented, and a scheme of using various colored tabs permits the following subdivision of the equipment: Cutting machines, loading machines, conveyors, battery-operated locomotives, battery-operated power trucks, drills and drilling machines, rock-lusting machines, pumps, room hoists, air compressors,, and miscellaneous, The greatest number of approvals granted to a single manufacturer is 80; the next highest is 65, and the third is 49. Several manufacturers have been granted only a single approval. The chart shows all approvals granted for, motored equipment. Some of these units have since become obsolete, and a few are used to a very limited, extent if at all.

Jan 1, 1941

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By E. P. Youngman

The mining laws of Russia (Collection of Laws, vol. 7, 1912) are still in force in Latvia. The Free State of Latvia (declared independent on November 8, 1918) is composed chiefly of the Baltic Provinces of the former Russian Empire, which are ethnographically Lettish: The Province of Courland, four districts of the Province of Livonia, and three districts of the Province of Vitebsk. Since the establishment of its independence, Latvia has not felt the need of a special mining law, inasmuch as mining so far has not been found profitable in that country. A supplement to this paper, entitled "Mineral Resources," is a brief summary of the minerals found and utilized in latvia. RIGHTS OF FOREIGNERS A foreign individual is permitted to explore for minerals and to own and operate mines in Latvia on equal terms with Latvians. A foreign corporation is required to establish a branch in Latvia, which shall be subject to the corporation laws of the country. A certain number of the partners or incorporators must be citizens of Latvia.

Nov 1, 1931

By Steven J. Page, John A. Organiscak

Prolonged exposure to airborne respirable coal mine dust is responsible for coal workers' pneumoconi¬osis (CWP): Furthermore, miners who show evidence of higher radiographic categories of simple CWP are at increased risk of developing progressive massive fibro¬sis (PMF). As of 1990, there were nearly 130,000 coal miners in the United States. "' This excludes mines that produce less than 10,000 tons annually and the anthracite coal mines. Estimates indicate that at age 58, an average of 7/1000 U.S. workers and 89/1000 U.K workers will have developed PMF(2-1) Health research studies have iden¬tified that the risk of developing and the severity of CWP arc directly related to (1) the amount of respirable dust exposure and (2) the coal rank.,'- The rank of coal is its stage of formation in the series peat, lignite, sub-bituminous, bituminous, and anthra¬cite (in order of increasing rank). The rank of coal can also be represented by the com¬mercially important characteristics specified by its proximate analysis: fixed carbon, vol¬atile matter, mineral matter, and moisture content.

By Michael A. Evanto, George J. Karabin

The Mine Safety and Health Administration, Pittsburgh Safety and Health Technology Center, Roof Control Division, is routinely involved in the evaluation of ground conditions in underground coal mines. Assessing the stability of mined areas and the compatibility of mining plans with existing conditions is essential to ensuring a safe working environment for mine workers at a given site. Since 1985, the Roof Control Division has successfully used the boundary-element method of numerical modeling to aid in the resolution of complex ground control problems. This paper presents an overview of the modeling methodology and details of techniques currently used to generate coal seam, rock mass, and gob backfill input data. A summary of coal and rock properties used in numerous successful evaluations throughout the United States is included, and a set of deterioration indices that can aid in the quantification of in-mine ground conditions and verification of model accuracy is introduced. Finally, a case study is detailed that typifies the complexity of mining situations analyzed and illustrates various techniques that can be used to evaluate prospective design alternatives.

Jan 5, 1999

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX C - HOISTING SYSTEMS - AVAILABLE EQUIPMENT C 1 - Introduction A survey has been made of available hoisting equipment which has applications for use in metal and non-metal mine emergency escape hoist systems. The information was gathered from a number of sources, including representatives in the USBM and MESA, mine operators, personal visits and telephone interviews with manufacturers, field visits to inspect equipment, advertisements, catalogues and indices of manufacturers. Wherever possible, technical specifications and prices were checked out with the manufacturer, or supplier. The sections on individual sub-systems and components, such as automatic control systems, winches and controls, are not intended to be all encompassing surveys. Rather a reasonable number of representative units in each category are discussed. The sample is large enough to provide a general picture of the kind of equipment available, including the abilities and limitations and a reasonable price range. The survey has been divided into six categories 1. Complete Hoisting Systems A Above ground installations B Below ground installations 2. Hoist Assemblies ^(Man-rated) 3. Hoists (not Man-rated)

Jan 1, 1976

By Launa G. Mallett, Charles Vaught, Kathleen M. Kowalski, Charles D. Litton, Michael J. Brnich, Ronald S. Conti, Henry P. Cole, William J. Wiehagen

How do people behave when they are trying to get out of a fire? Are escape activities different in each incident, or will most actions be predictable across events? Do persons make the same sorts of decisions whether they are responding as individuals or as group members? Because the social costs of fire-related deaths and injuries are likely to continue to rise, societal pressure for greater safety will also undoubtedly increase. There are, therefore, compelling reasons to further our understanding of action in fires. If human behavior in fire is studied scientifically and predicted according to some well-defined principles, the benefits will be significant. Design engineers could incorporate real-world findings into their plans. Equipment manufacturers could gain from insights into how their technology is actually used in fire emergencies. Safety personnel would have a better appreciation of what constitutes adequate evacuation procedures. Trainers could upgrade the content of their courses that teach escape skills. The result would be an overall improvement in the quality of fire preparedness and safety.

Jan 1, 2000

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.