Search Documents

By D. J. Bauer

A solvent-extraction system employing selective stripping of a pre loaded organic phase was investigated for recovering Sm203 from a light-group rare-earth mixture. The samarium concentrated in the organic phase, and a >99-pct-pure samarium oxide product was obtained at 76-pct recovery in a 20-stage operation using di(2-ethylhexyl) phosphoric acid (EHPA) as the organic phase. The stripping agent was a 1.5-pct hydrochloric acid solution containing 200 g NH4C1/1.

Jan 1, 1972

By Joseph Cervik

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

A series of economic evaluations of processes for producing metallurgicalgrade alumina from low- grade aluminous materials is being conducted by the Bureau of Mines to determine the relative processing costs . The two processes considered in this evaluation are concerned with the recovery of alumina from clay through the formation of ammonium alum . In the first process , dehydrated clay is leached with ammonium bisulfate solution ; in the second process , clay is baked with ammonium sulfate and then leached with water containing a small quantity of sulfuric acid . After the alumina is dissolved by either of these methods , the iron is reduced to the ferrous state to avoid crystallization of ferric sulfate with the alum . The recovery of pure alum requires two crystallization steps . The alum crystals are then redissolved and precipitated with ammonia to produce alumina hydrate , which is calcined to a - alumina . These evaluations are based on published work , and the proposed plants are designed for a capacity of 1,000 tons of alumina per day . The estimated operating cost per ton of alumina for the bisulfate leaching process is $ 117.06 , and for the sulfate baking process , $ 109.26 . Using a Marshall and Stevens chemical equipment index basis of 240.0 , the estimated fixed capital costs , in the same order , are $ 158 million and $ 146 million . Under current economic conditions , these two processes are not competitive with the Bayer process for the production of alumina from bauxite . Since small improvements will not reduce costs sufficiently to approach competitive costs , future research work with these processes should be confined to areas likely to result in major cost reductions .

Jan 1, 1965

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 2010

By Bobby B. Gillenwater

This report presents recommended guidelines and regulatory changes applicable to electrical installations in underground oil shale mines. These recommendations are based on information gathered from oil shale operators, government agencies, and other knowledgeable sources familiar with existing plans for mining systems and electrical installations, and on present understanding of the problems and hazards associated with oil shale mining. Additional discussions of specific electrical problems related to oil shale mining are also presented. These specific problems include: ? Ground fault current levels ? Permissible electric wheel motors ? Permissible batteries and electric starting systems ? Intrinsically safe instrumentation and applicability of existing test standards.

Jan 1, 1983

By John J. Sammarco

Light-emitting diodes (LEDs) are emerging as viable replacements for incandescent (INC)-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. This paper describes the performance of LED and INC sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and air flow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Second, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and INC sources can be magnified toward the end of a 10-h battery discharge cycle. Empirically, we have determined that after 8 h at an ambient temperature of 25 ?C, the average light output of an INC cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery, and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and air flow on the light output of an LED and INC cap lamp were conducted in the National Institute for Occupational Safety and Health Safety Research Coal Mine. The LED cap lamp yielded a vertical average illuminance improve­ment of approximately 9.5%, and the INC cap lamp yielded a vertical average illuminance degradation of approximately 4%. The differences between LED and INC cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38% more efficient than the INC cap lamp with a lead-acid battery at the end of the 10-h driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the INC light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, particularly given that the light output will decrease an additional 30% to 45% over the period of a 10-h shift. The implications of the differences between LED and INC sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and INC cap lamp visual performance research.

Jan 1, 2009

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

By A. Visnapuu

The Bureau of Mines, as a part of its goal to minimize occupational hazards associated with mining and mineral processing operations, has developed and field tested a compact exhaust air muffler for mechanized, jumbo-mounted pneumatic rock drills. The muffler is constructed of 1/8-inch sheet steel and has nominal dimensions of 1-3/4 by 9 by 13 inches. A directed air passage, flexible neoprene baffles, and an expandable slit-type outlet are incorporated to reduce drill exhaust air noise and eliminate muffler icing. Field tests in actual mining operations showed a l5-dbA reduction in exhaust noise and an 8-to 12-dbA reduction in overall drilling noise with no icing problems or decrease in drill performance. Data are presented on muffler construction, laboratory, and field test results.

Jan 1, 1979

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By H. B. Hill

Virtually from the date of its discovery in December 1928 the Oklahoma City oil and gas field, Oklahoma County, Okla., has attracted national and international attention. The history of the field has been associated closely with rules and regulations pertaining to production control and proration practices. Early development was rapid, and Oklahoma City soon attained the distinction of being the first major field in which the producing wells were over a mile in depth. Before the structural features of the reservoir had been disclosed every outpost well was considered a "wildcat", so complex appeared the underground geology, The wells not only were deep and the reservoir pressures high, but the production from the early wells was a high A.P.I. gravity oil, accompanied by large volumes of gas. Several "blow-outs" and fired occurred during the early development, and the close proximity of these now unusual events to a large city gave the field much publicity, both local and national. Later, when its production threatened to demoralize the market for oil and its products, the Oklahoma City field again attracted wide publicity. The then little understood geology of the underground reservoir and the diversity of ownership of the land overlying the producing structure made orderly development and production difficult to enforce. Proration was enforced with difficulty., and the, rate of production from the field continued to increase until, on August 4, 1931, martial law was declared in all prorated fields of the State, and most of the wells in the Oklahoma City field wore shut n. On October 9, 1931, permission was granted t o reopen and prod e the wells in the Oklahoma City field. The order permitting production of the wells provided that during the period beginning October 10 and extending to October 20, 1931, all wells in the field that hid not produced more oil than specified under the earlier proration orders and that had been shut in for the required 55-day period were permitted to produce 5 percent of their last potential during that 10-day period. On November 7, 1931, the Corporation Commission of Oklahoma issued an order which divided the Oklahoma City field into the Wilcox, Arbuckle, and Lower Simpson zones for proration purposes. Wells producing from the Wilcox zone were allowed to produce 4 1/2 percent of their potential5/ from November 1, 1931, to January 1, 1932; Arbuckle limestone wells were allowed to produce 250 barrels of oil daily; and Simpson sandstone wells which had a potential of over 2,000 barrels per day or which made 3 percent or more water were allowed to produce 200 barrels of oil per day.

Jan 1, 1937

By W. J. Wiehagen

The Work Crew Performance Model (WCPM) seeks to define performance variability within similar tasks of an underground work crew and relate observed variability to a cost consequence. Performance variability is described using work site observations to determine the adherence to job elements con¬tained within a standard operating procedure. Key components of the WCPM include (1) job definition through task analyses and the ranking of job elements by perceived cost consequence, (2) observational techniques for establishing performance baselines by measuring adherence to safe and proficient job procedures, and (3) cost linkages between adherence to task procedures and measures of consequence for noncompliance. Data presented within this report were obtained through the study of shuttle car operation in an underground mine in Appalachia. Observed adherence to safe and proficient job procedures by opera¬tors matched well with the consensus profiles (measured through a nominal group technique) with min¬ing personnel. It was also found that experienced operators consistently outperformed less experienced, incidental operators. These findings imply potential use of the WCPM as a practical procedure for thinking systematically about the choices available to reduce performance variability. Field application of the model can offer useful data to evaluate training and financially support performance improvement strategies that can be tested for their ability to reduce human error.

Jan 1, 1994

By Raja V. Rarnani, Robert L. Frantz

"Co-Directors, Generic Mineral Technology Center for Respirable DustEarly in the 1980s, the U.S. Bureau of Mines initiated the concept of the Generic Center, incorporating it into its mining research program, and in 1983, the Generic Mineral Technology Center for Respirable Dust was established. The Generic Center concept was first envisioned by the U.S. Bureau of Mines as a way to bring together the various different scientific, engineering and medical research interests in the respirable dust area to effect a coordinated and efficient organization for advancing knowledge in that field. The result was a combination of the collective talents and skills of more than 100 scientists, engineers, medical personnel and graduate students, through the formation of a consortium of five major research universities, including medical facilities, to perform respirable dust research. The Generic Mineral Technology Center for Respirable Dust consortium comprises The Pennsylvania State University (with its Hershey Medical Center) and West Virginia University (with its Medical Center) as the lead universities and the University of Minnesota, Massachusetts Institute of Technology and Michigan Technological University as affiliates.Although respirable dust-related disease remains the nation's worst industrial hazard, the fundamental understanding of all aspects of respirable dust associated with the mining and milling industries, including the interaction of dust and lungs, has grown significantly over the past near-decade toward the larger effort to reduce the incidence and severity of disease caused by respirable dust. Continued progress toward making the mine work environment cleaner and healthier remains the immediate objective of the Respirable Dust Center.The Respirable Dust Center's research program and technology transfer activities, described in this paper, exemplify the Generic Center concept first envisioned by the U.S. Bureau of Mines. Interdisciplinary and interactive studies continue to result in significant progress toward making mine atmospheres cleaner and healthier."

Jan 1, 1995

By A. L. Engel

Simple treatment methods, employing the least possible equipment, can sometimes be established for marginal ores and economical results achieved. In continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno Station of the Bureau of Mines, typical ores from newly discovered or recently explored mining districts have been investigated. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores, as well as the conservation and recovery of values in products from former operations that were discarded because of past inability to treat them economically. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas some involved samples of old dumps or tailings piles. The test, work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials; and because, inasmuch as the samples were representative of the districts from which they were obtained, this in-formation should be helpful in the future development of these districts. The present report is a compilation of results of brief preliminary tests on oxide ores only, which contained gold and silver and in some cases base metals. The methods of treatment used include gravity concentration, amalgamation, flotation, and cyanidation. For the most part, only standard laboratory procedures were employed. No attempts were made to develop new methods for the low-grade refractory ores in this group of samples if simple treatment was not successful, as the stage of development of the properties did not warrant extensive experimentation on the samples submitted.

Jan 1, 1951

By Oliver Bowles

"Underground operation.In its broader sense the term ""mining"" is applied to all processes whereby raw materials are taken from the earth to be used as sources of mineral products. In a more restricted sense ""mining"" is applied to underground operations as contrasted with open pit work designated as quarrying. The tern is used in the restricted tense in this paper; for it relates to the exploitation of limestone deposits by modern methods of underground operation rather than by open pit methods.Present tendency toward miningIt may seem to some readers that a paper on mining limestone will find little general interest among lime plant operators, for only a limited number of them have yet resorted to this means of procuring raw materials. It is noteworthy, however, that a growing tendency exists toward underground operation, for one by one quarry owners are faced with increasing difficulties in open pit operation. It seems desirable, therefore, for operators to keep closely in touch with this gradual change in process, to inquire into the underlying causes, to compare costs, and to study the effects of the change in method on subsequent steps in calcining the stone to produce lime."

Mar 1, 1924