Search Documents

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

By W. C. Holliman

Commercial production of synthetic rubber in the United States became a reality in 1931 when E. I. duPont de Nemours, Inc., announced the manufacture of Duprene, a synthetic rubber made by polymerizing r chloroprene. Duprene was later improved and reintroduced as neoprene. Since 1931 other synthetic rubbers and rubberlike materials have been announced and are now produced commercially or are in the pilot-plant stage in the United States. These include Thiokol, Buna S, Perbunan, Koroseal, Vistanex, Flamenol, Ameripol or Hycar, Chemigum, Butyl rubber, and Flexon. None of these is synthetic rubber in the strict chemical meaning of the word synthetic, as none is identical in chemical structure with natural rubber. However, all possess some of the physical properties of natural rubber, and in addition usually have some outstanding property not found in natural rubber that makes them superior for certain uses. Because of these superior qualitites, a considerable demand had arisen for synthetic rubbers before the present emer¬gency, although the price was several times that of natural rubber.

Jan 1, 1943

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By John A. Organiscak

The Bureau of Mines conducted a survey of eight shearer longwall operations to identify factors that affect respirable dust generation from longwall roof supports. The longwalls surveyed were in coal seams located in different geographic regions of the United States. Data were collected on mining (geologic) conditions, support design, operational characteristics, and amount of respirable dust generated from roof supports. Analysis indicated that mining conditions are the main factors that affect the generation of dust during roof support movement. Both roof strength and depth of cover above the coal seam showed relationships with the amount of support dust generated. Several practices are currently employed to effectively control roof support dust; however, some of these controls are limited. More research and development is needed to improve dust control technology for longwall roof supports.

Jan 1, 1985

By W. A. SLOAN, G. L. Oldright, J. D. Sullivan, E. K. PRYOR, A. F. HALLET, R. S. Dean, S. L. BROWN, F. S. Wartman, A. J. Thompson

Lack of sufficient publication funds has resulted in the accumulation of considerable unpublished experimental work on copper metallurgy by the Bureau staff . The present report gives extended abstracts of this work , as well as a discussion of the best direction for future efforts . The experimental work reported in this series of papers was done in cooperation with the University of Arizona , Tucson , Ariz . The investigations covered in the third , fifth , and seventh papers were done under the direction of G. L. Oldright and the remainder under the direction of V. H. Gottschalk .

May 1, 1934

By S. H. Ash

Tunnel driving is recognized as one of the most hazardous of occupations; this is a reflection of the high accident severity rates and resultant high compensation and similar costs in this industry. Most tunnels are driven by contractors who bid for the jobs, taking into consideration the prevailing industrial insurance rates at the time the bids are placed. After the bid is secured the contractor then attempts to complete the job at the minimum cost to himself. In a sense the accident-cost item is fixed for at least one year when a policy is secured. Time is generally an important factor not only for the contractor, but also for the insurance carrier and the assured. If the assured represents a private interest, the cost burden usually is ultimately placed on the general public which avails itself of the service contemplated; if the project is a governmental enterprise the cost burden unquestionably falls upon the general public involved and on the general tax payer. For these reasons it is of vital interest to the public that accidents not only be kept at a minimum as a humanitarian objective, but also because the accident-cost burden, too frequently not even realized and considered to the degree that it should be, can assume proportions that materially affect the cost of the enterprise. The basic industrial insurance rate for tunneling in California in 1932 contemplated an earned premium of 12.12 percent of the labor pay roll. The State has been particularly engaged in large construction enterprises, some of which involve high accident cost rates, notably structural-steel bridge building, which contemplates an earned premium of 19.65 percent of the labor pay roll. When this figure is compared with the much lower rates that apply to other industries it is apparent that a heavy toll in human wreckage is taken by such engineering projects, which must be viewed as monuments to human suffering as veil as to human achievement.

Jan 1, 1933

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By L. M. Adams

Experiments in reclaiming acidic surface-mined coal lands with raw fly ash from bituminous-coal-fired powerplants were conducted by the Bureau of Mines at two sites in northern West Virginia. Plots at both sites were treated with varying tonnages of fly ash from three area powerplants and were planted with a variety of grasses, legumes, trees, and shrubs. Eight grasses and seven legumes were investigated. Greatest promise for growth under harsh soil conditions was shown by Kentucky 31 fescue, rye and red top grasses, and birdsfoot trefoil, a legume. Survival of trees and shrubs was negligible. Addition of fly ash to the spoil increased the pH to a range tolerable to some types of plant growth, improved the texture of the soil, and increased the available water of the resulting mixture.

Jan 1, 1971

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines' horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau's methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

By D. E. Redmon

Exploration of hidden mineral deposits becomes increasingly important as known ore reserves are depleted. The primary objective in any exploratory program is to obtain enough reliable information to evaluate accurately the potential of the mineral deposit. Constant improvement in equipment and technique has established drilling as one of the most valuable methods of exploration. This paper presents the results of studies of several drilling methods currently used in the search for uranium deposits in sedimentary formations from surface drill sites. Also presented is a description of drilling with wire-line equipment from an underground location in metamorphic rocks. The studies were conducted in the Colorado Plateau area and in northwestern New Mexico and Wyoming. Statements of a general nature pertain to conditions or situations existent in those areas.

Jan 1, 1960

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of manganese from known domestic occurrences. Eight of these deposits were found to have demonstrated resources totaling 420 million metric tons with an average grade of 10 percent contained manganese. They were found to be submarginally subeconomic. Economic evaluations of the eight deposits resulted in incentive prices ranging from $8 to almost $35 per long ton unit (22.4 pounds) of contained manganese. Comparing these prices with the current market value of $1.70 per long ton unit of manganese clearly illustrates the submarginal nature of the domestic ores analyzed. These domestic resources would probably not be developed except in the case of an extreme national emergency. Production from the eight deposits would take 3 to 6 years to develop, and the final product would be manganese ore concentrate, which could be used in the production of ferromanganese. If preproduction development began in 1981, annual production would peak in 1987 with 900,000 metric tons of recoverable manganese. Thereafter, production would see a steady decline unless additional resources were located or technologic improvements were made to allow processing of lower grade material, or unless mining and processing of ocean manganese nodules began to take place.

Jan 1, 1982

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

By Will H. Coghill, Fred D. DeVaney

"INTRODUCTION The Mesabi iron district of Minnesota has a potential production of over 50 million tons of iron ore annually. The large shipments of ore each year are gradually depleting the reserves, and if the present rate of production is to be maintained there must be a growth in the present available ore supply.Growth is a natural course. The growth of a city may be affected by the addition of city blocks or by the improvement of utilities necessary for its betterment, these may go on in the order named or concurrently. The city-block type of growth of the Mesabi has been tremendous, and the ""betterment"" type has followed in due course. Probably the former has reached its limit, and if so, more time will be allotted to the latter. It is not the intent of this paper to present either a eulogy of the wonderful mining methods or a history of the milling, but it is pertinent to say that if the lean-ore area continues to produce, the continuance will be more the result of further improvement of milling methods now well under way than of extension of boundaries by the city block plan of growth.In an examination of the western end of the Mesabi district one finds sludge basins containing millions of tons of millable ore rejected by washing plants which were built for economy in operating cost and with little thought of conservation, and rich tailings piles of jigging plant rejects. In addition, there is an appreciable tonnage of bawl rake pro-ducts so low-grade that it requires mixing with the best ore of the district to make it merchantable.Any of these three products is a source of additional reserves, but gangue must be removed before the products will comply with blast-furnace stipulations. All investigators are agreed that to effect this separation comminution must be fine enough for liberation, but beyond this point opinions diverge; some would seek new processes, while others adhere to methods and machines developed in other mining districts.In the investigation by the Mississippi Valley Experiment Station of the United States Bureau of Mines working in conjunction with the Missouri School of Mines and Metallurgy,Rolla, Mo., the latter course has been followed. Attention was first given to the sludge basins mentioned. From their contents good grades of concentrates were made and the results published 4 later commercial-scale tests were made in a pilot plant of 10 tables, and the laboratory results were confirmed, The tailings from jigging plants are high in iron, and a study of their possible retreatment showed that if they are recrushed, high recoveries of acceptable grade may be expected. The results will be published later."

Apr 1, 1932

By G. L. Oldright, Virgil Miller

"INTRODUCTION The first ten papers of the series on smelting in the lead blast furnace described the operation at the custom smelter of the International Smelting Co., Tooele, Utah, and at the plant of the Bunker Hill Smelting Co., Kellogg, Idaho, which handled a very rich lead concentrate. These previous papers may be considered a picture of the traditional lead smelter treating custom ores and of the smelter that will treat the type of product likely to be made in the future - lead concentrates of an increasingly rich grade.The great plant at Trail is of special interest to those smelting lead products containing much zinc and faced with the necessity of transforming all of their byproducts into commodities which may be sold profitably. The plant is equipped to produce electrolytic zinc, lead, copper, silver, bismuth, and cadmium. Part of the sulphur evolved from treating the ores is converted into sulphuric acid. Complete fertilizers for agricultural purposes are also produced.The smelter of lead ores has long considered that zinc is one of the most difficult ingredients that he has to handle. Even with the gretat improvement in flotation practice today, the residues from electrolytic zinc plants leaching zinc concentrates must still be smelted for their lead content. Of the total gangue material not separated from the lead concentrate sent to the smelter, zinc is still one of the most notable in percentage. The most successful way of coordinating the over-all operations of a concentrator, an electrolytic zinc plant, and a smelter provided with a plant for re-treating the blast-furnace slag for its lead and zinc content must be of interest to many treating complex ores.ACKNOWLEDGMENTThe data in this paper were collected in cooperation with the Consolidated Mining & Smelting Co. of Canada, Limited, and its entire technical staff. Detailed acknowledgments of assistance received are given in the papers from which this one is briefed."

Sep 1, 1934

By Michael J. Klishis

It was the goal of this project to develop training materials specific to two areas of the mining industry: (1) safe use and care of the self-contained self-rescuers, and (2) awareness and avoidance of electrical hazards. This report describes the development of the following training material: Instructor's modules for the OCENCO EBA 6.5, CSE AU-9A1, and PASS 700E self-contained self-rescuers; and a textbook, slide tapes, and accident case study scenarios for mine electricity, and a computer based instructional package on mine electricity and electrical hazards. The report concludes that additional efforts are needed in mine training and four recommendations are made: (a) tailor existing materials to fit specific mine sites, (b) develop and evaluate computer based instructional material, (c) develop parallel training materials for metal and non-metal mines and, (d) develop additional training materials for preparation plants and surface areas of underground mines.

Jan 1, 1985

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By G. J. Slavens

The Bureau of Mines has devised technology to recover cobalt, nickel, and byproduct copper from domestic lateritic material using an oxidative, ammoniacal ammonium sulfate leach. Nickel, cobalt, and copper were recovered by solvent extraction and electrowinning. To reduce the cost and complexity of cobalt recovery, an alternate method using lig-nite to extract Co3+ was investigated as reported herein. In the first 25 BV (bed volumes) of solution contacted with lignite, 97 wt pct of the Co3+ was extracted in & downflow column at pH 9.3. After 85 BV, the lignite was loaded to 1.5 wt pct Co3+ and further ex-traction was minimal. The lignite extracted cobaltic ammine complexes rather than cobalt ions and was nonselective as to other -metal cations and ammonium ions. Deleterious cations and 80 wt pct of the nonammine ammonium ions were removed prior to acid elution of the lignite. The removal of the ammines prior to elution to produce an ammonium-ion-freeCo3+ eluate was only partially successful. Thus Co3+ removal from ammoniacal solutions by lignite is technically difficult and economically unfeasible. It was also determined that reduction of Co3+ to Co2+ occurred during the extraction-elution process.

Jan 1, 1984