Search Documents

By W. W. Odell

The results of the 1921 cooperative experiments conducted by the U. S. Bureau of Mines and the University of North Dakota at the University mining substation plent at Hebron , North Dakota , pointed clearly to certain definite dep ficiencies in the schemes hitherto developed for benefiting and utilizing lignite . First The apparatus used in the carbonizing process or used to produce carbonized lignite suitable for briquetting is too costly , that is , the cost per ton day of residue made is too high . Second - The depreciation of the carbonizing appara tus is too high . Third The carbonizing apparatus can not be operated intermittently without seriously damaging it and impairing its efficiency of performance . Fourth Too little attention has been given to the possibility of using at least a certain percentage of the carbonized lignite directly in suitable stoves and furnaces without briquetting or other treatment . Accordingly , consideration was given to the design of an oven that could be built at a mine without the importation of highly skilled and specially trained construction men , erected at a low first cost , readily kept in a state of repair , operated at a rela tively high capacity and put into operation or shut down at will without seriously damaging the brickwork . The need of such an oven was appreciated also by the University of North Dakota and a cooperative agreement was made to build and operate such an oven during the summer of 1921.

Feb 1, 1923

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

By S. R. Zimmerley, C. H. Schack

"INTRODUCTION The pilot-mill concentrator at Boulder City, which has a nominal capacity of 40 tons per day, was planned and built to investigate further the beneficiation of domestic manganese ores that have been concentrated successfully in the ore-dressing laboratory. As milling of manganese ores in general is a new field, it is necessary to prove the success of laboratory processes by means of large-scale operations employing standard milling equipment, and thus to obtain engineering and metallurgical data essential to designing and operation of full-scale concentrating mills.The first ore tested in the pilot plant was the Three Kids Annex manganese ore from the Las Vegas Wash area 15 miles southeast of Las Vegas, Nev. The deposit was worked for its high-grade ores during the First World War From 1930 to 1939, 4,500 feet of diamond drilling was completed by a private company. Diamond drilling started by the Bureau of Mines in November 1940 and completed in July 1941 aggregated 6,600 feet. Exploration by the private company and the Bureau outlined reserves of about 1,000,000 tons of ore assaying plus 28 percent manganese. A much larger tonnage of lower-grade ore also was outlined by the drilling.Because of its physical nature, the Three Kids Annex ore had long proved unamenable to concentration by ore-dressing methods. The ore is a mixture of manganese oxides (wad) filling the pores and to some extent replacing a silt composed of very fine grains of volcanic tuff, quartz, feldspars, other silicates, and clay. Some gypsum occurs as fillings along fracture planes. The ore is light and very porous. Upon wetting, it disintegrates into granular but friable particles and a large amount of slime. It is these characteristics that make the ore so difficult to concentrate."

Sep 1, 1947

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

By J. M. Riley

The Bureau of Mines investigated a promising new technology for recovering A1203 from alunite to support the Bureau's alumina miniplant project. Results are presented for a study of the technical feasibility of treating alunite crushing and grinding reject fines for recovery of A1203. Alunite pellets having sufficient strength and resistance to degradation were produced by combining fines and coarse alunite with a KOH binder. The best pellets were prepared, in a laboratory pelletizer, by adding 1 pct KOH as a 5-pct solution to a mixture of 40 pct alunite dust (98 pct minus 65 mesh) and 60 pct coarse alunite (minus 20 plus 65 mesh). Calcines suitable for K2SO4 and A1203 recovery were produced by reducing dehydrated alunite pellets with sulfur in a laboratory shaft furnace for 4 h at 600° C, followed by air oxidation of the reduced calcine for 1 h at 600° C. This report presents design calculations, schematic diagrams, and discussions of the essential features of a proposed process research unit (PRU)--a continuous, 6-lb/h alunite shaft furnace--for studying the process.

Jan 1, 1983

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions. In recent gears these questions have tended to increase with the use of mechanical appliances. Twenty-five years ago electricity had been used but little in mires; today there is practically no other means of transmitting power employed in American mines, except that in metal mines compressed air is used, chiefly for drilling and for operating small portable hoists. In coal mines there has been a great increase in mechanization, which tends to concentrate the work of production in small areas and to increase the local difficulties of ventilation; also, it has intensified locally the hazard from coal dust as well as firedamp in bituminous and subbituminous mines. The answers to the questions that arise are not always obvious, as is shown by the fact that even able, experienced men differ in their opinions of the best, way to overcome a particular mining hazard. The difficulty of .solving the problems is also demonstrated by the varying provisions in mine-safety rules, both in official regulations and in the rules of those mining companies that are endeavoring to do more than follow the letter of the law. Such differences of opinion as to the best way of meeting a difficult situation are often found within the same mining organization, and, similarly, varying opinions are held by different members of the Bureau of Mines staff.

Jan 1, 1937

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By R. D. Groves

Laboratory research has demonstrated that high - grade copper powders can be produced under controlled conditions from cement copper products . The technique should enable small producers to prepare a directly marketable product by means other than smelting and electrolytic purification . A continuous drum- type precipitator was the preferred unit for producing fine - sized particles of cement copper that were further processed by chemical digestion in a copper sulfate solution , by reduction and sintering in a hydrogen atmosphere , and by grinding to a powder . The effects of variables related to all stages of the process were investigated . Treatment of leach solutions from three different sources resulted in copper powders containing 99.2 to 99.8 pct Cu , apparent densities of 1.97 to 2.25 grams per cu cm , good powder flow rates , and a size distribution of 54.9 to 60.1 pct minus 325 - mesh material .

Jan 1, 1964

By D. A. Wilson

Several promising systems for selectively oxidizing the iron in an iron-tin alloy commonly called "hardhead" were investigated in a research project conducted to devise a method for recovering tin from this troublesome alloy. A satisfactory oxidation method was developed and tested successfully on melts of 2,000 grams. Molten hardhead (near 1,080° C.) was blown with air to oxidize iron and leave tin in the reduced state. Recovery of available tin was 96 to 98 percent. Tin products contained 2 to 0.1 percent iron which was reduced to 0.06 percent by filtration at 250° C. Iron oxide formed during oxidation was absorbed by a fluid flux cover composed of 43 percent silica, 17 percent burned limestone, and 40 percent fused borax. Less successful but nevertheless promising results were obtained with mixtures of steam and hydrogen which were sufficiently selective at temperatures between 600° and 950° C. but did not result in complete oxidation of iron. Carbon dioxide-carbon monoxide mixtures also oxidized iron selectively but incompletely. Both stern and carbon dioxide systems produced sufficiently encouraging results to additional research on these systems.

Jan 1, 1961

Real gross national product increased at a larger-than- expected annual rate of 8.3 percent in the first quarter of 1984, with both consumption and investment spending increasing significantly in real terms (table 1). Residential and nonresidential fixed investment increased at annual rates of 25.7 and 14.6 percent during the first quarter of 1984, and investment in nonresidential structures, which declined in 1983, also increased during the first quarter of 1984, nearly attaining its 1982 level. The annual level of personal savings increased $27.7 billion, while the personal savings rate (the ratio of personal savings to disposable income) increased to 5.8 percent during the first quarter. The increase in the personal savings rate comes as welcome news to analysts concerned over the flow of loanable funds to the private sector and the impact on interest rates in 1984 of increased private and Government demands. U.S. Minerals Industry Performance A major upswing in the performance of the metal mining sector occurred during the first quarter of 1984, with production increasing almost 11.2 percent from January to March, The recovery of the metal sector is also reflected in the performance of primary metal industry profits, which were positive during fourth quarter 1983 following seven consecutive quarterly losses (table 1). Two thousand nine hundred more metal mining production workers were employed in February 1984 than in February 1983.

Jan 1, 1984

By W. C. Phalen

During the search for deposits of soluble potash salts in the United States, carried on by the United States Geological Survey, much information was collected on the salt resources and industry of the United States. The more important features of the information thus gathered, compiled, and digested may be classified under five headings, as follows: 1. Geology of the salt deposits of the United States. 2. Theories relating to the origin and formation of salt deposits. 3. Chemical composition of saline materials in the United States, principally rock salt and natural and artificial brines. 4. Statistics of salt production in the United States. 5. Technology of salt production. The first four items are not discussed in this report, but their treatment will comprise a separate report published by the Geological Survey,a which will supplement this report, relating to salt-making processes, and will describe comprehensively the salt resources of the United States. Persons desiring a copy of that report should apply to the Director of the United States Geological Survey, Washington, D. C.

Jan 1, 1917

By E. R. Bauer

The U.S. Bureau of Mines is investigating strata interactions associated with mining of multiple coal beds to provide the mining industry with improved methods of planning and developing multiple coalbeds, conserving resources, and increasing the safety of underground coal mining. This study involves analytical predictions and underground observations of longwall development ground control problems at a south-central Pennsylvania coal mine affected by subsidence induced by multiple-seam mining. As predicted, strata interactions were found in upper mine areas mined over lower mine gob. Observations revealed roof deterioration accompanied by excessive water inflows in the first 170 ft after crossing the gob line as mining entered and exited the subsided area (over the lower mine gob). In contrast, superimposed mine areas and areas mined a substantial distance out over the gob showed no signs of interaction with previous lower seam mining, again as predicted.

Jan 1, 2010

By Wm. W. Odell

This report comprises a brief outline of the experimental cracking of natural gas in a water-gas generator at Louisville, Kentucky, and a discussion of the results obtained. The work was done under a cooperative agreement by the U. S. Bureau of Mines with the Louisville Gas & Electric Co. The re-forming or partial cracking of natural gas is not a new process, but one which has been employed in the manufacture of city gas for a number of years. However, the apparatus used heretofore was not a water-gas generator containing a bed of ignited fuel, but instead it was a plurality of connected chambers containing spaced and arranged checker bricks, with means for heating the bricks and for admitting the natural gas. The procedure previously followed was quite different from that used during the tests at Louisville; likewise the results obtained were different. It is not uncommon for companies distributing natural gas to provide gas-generating equipment for producing manufactured gas which is used, mixed with natural gas, during periods of peak demand. Because this equipment is idle much of the time, in some instances being in use only for a few days a year, some of the gas companies have considered using it, during off-peak periods, in the manufacture of some gaseous products and for carbon black which might he produced and marketed with profit. There is one plant of this kind at Louisville. Kentucky. Its maintenance in condition ready to be operated is necessary because of the limited supply of natural gas and because of the variation in demand. The engineers of the Louisville Gas & Electric Co. considered in particular the possibility of cracking natural gas in a water-gas generator by injecting the gas into the incandescent fuel bed, thereby producing a gas comprised largely of hydrogen (H2) and carbon black, an appreciable amount of which is entrained in the gas as it leaves the generator, Because power and gas are available at low prices, Louisville was believed to be a satisfactory location for a plant which could use hydrogen. It was evident that this method of treating natural gas might directly benefit the gas company by: 1. Lowering, the cost of manufactured gas.

Jan 1, 1930

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By McHenry Mosier

The Bell mine operated by the Warner Co. at Bellefonte, Pa., has an annual production of about 600,000 short tons of high-grade limestone. Since 1924, shrinkage stoping has been the mining method. Horizontal, long-hole diamond-drilling for production in stopes was started with one machine in July 1946. It is now standard practice. The burden on the holes is 10 feet. Diamond bits are noncoring EX-size in both concave and pilot types. The two types have little difference in drilling speed at the Bell mine. The diamond drills are mounted on 3-inch single-screw columns. Diamond drilling shows a marked increase in efficiency at the Bell mine, compared to percussion drilling, with respect to tons broken per drill shift, tons broken per foot of hole, and tons broken per pound of explosive. The advantages of diamond-drilling blast-holes also include (a) improved safety, greater footage per drill shift, (c) better frag- mentation of the broken, stone, and (d) reduction in amount of barring down required in stopes because the working places are limited to slots which have a relatively small area.

Feb 1, 1948

By Paul M. Tyler

Magnesite is of importance primarily as a refractory material for lining steel furnaces , although substantial amounts are used in the production of flooring compositions and other building materials and for certain chemicals , notably epsom salts . Since consumption for all of these purposes is largely in the eastern United States and domestic deposits are situated in California and Washington , this country's magnesite mining industry , which was created largely by war- time conditions , has subsequently been sustained by tariff protection .

May 1, 1931

By Daniel D. Sweeney

The United States coal mining industry has traditionally experienced difficulty in controlling dust levels below the occupational exposure limit. While improvements in face ventilation and water spray nozzles have decreased dust exposures, approximately eight percent of experienced coal miners are still developing Coal Worker?s Pneumoconiosis. This investigation tested the feasibility of enhancing existing engineering dust controls by mounting a simple barrier on a longwall shearer that separated the operators from the cutting drums. The barrier was constructed and tested above ground at the National Institute for Occupational Safety and Health Pittsburgh Research Laboratory longwall gallery test facility. A 96-percent reduction of respirable dust occurred at the headgate sampling position when tested at 2.4 m/sec (480 ft/min). The average dust level decreased from 39 mg/m3 to 1.5 mg/m3 by utilizing the barrier.

Jan 1, 2009

By M. M. Fine

"INTRODUCTION One of the principal activities of the Bureau of Mines during the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydro-fluoric acid, such as the use of the anhydrous acid as a catalyst in high-octane-gasoline production and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorspar. 2/ In 1943 the consumption of acid-grade fluorspar was advancing at a more rapid rate than production and was only slightly less than production during the latter half of the year.The outlook for the postwar market for fluorspar is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid also are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a new peacetime demand for fluorspar equal to 60 to 75 percent of the war production, 5/ 6/ and others believe that the fluorspar industry will be permanently expanded. 7/"

Dec 1, 1947