Search Documents

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By Khamis Y. Haramy

This U.S. Bureau of Mines report describes the use of Bureau-developed flat and cylindrical hydraulic borehole pressure cells. A brief description of the fabrication, installation, and pressurizing equipment is given and pressurizing procedures are discussed. Theories available on evaluation of data from the flat and cylindrical pressure cells and examples of data analysis and stress evaluation are also presented.

Jan 1, 1991

By Rov G. Stott

In recent years there has been no loss of life from fires in the underground mines of the Lake Superior district, but numerous minor fires and several serious ones involving loss of property and production have occurred. The iron-ore-producing companies recognize that well-equipped mine rescue stations are a valuable asset against the ever-present ranger of mine fires or the possibility of hazardous atmospheric conditions underground. Prompt action by trained and properly equipped rescue teams is recognized as the prime essential in saving lives, property, and production when fires occur. To achieve this purpose, the mining companies have provided themselves with mine rescue equipment and maintain trained mine rescue crews. This circular describes how one progressive company has provided, maintained, and improved upon such protection for its underground iron-ore mines on the Marquette and Menominee iron ranges of Michigan's upper peninsula. SUMMARY The central mine rescue station of The Cleveland-Cliffs Iron Co. at Negaunee, Mich., has provided the company's mines with competent and well-equipped mine rescue teams. The new central mine rescue station at the Mather mine "B" shaft has the distinction of having underground training facilities provided as a part of the station. The company maintains the largest trained force in mine rescue in the Lake Superior district, and mine rescue training is employed as a part of the accident-and fire-prevention program. One of the most important results has been the promotion of closer cooperation and understanding between the management and the workmen. In addition to the service rendered to company mines, the station and its personnel have given assistance to others. The station and its equipment have also been used for training several nearby community volunteer fire departments. This mine rescue station and its personnel have been a dependable and valuable asset to the community in which it is located.

Jan 1, 1954

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By Joseph J. Wallace

1. The investigation shows that nine coal beds have been mined in Harlan County, of which the Harlan and Upper Elkhorn No, 3 are the most important from the standpoint of present production. Of less importance are the Hindman, Flag, Haddix, Wax, Fire Clay, Armburgy, and Upper Elkhorn No. 2. The Harlan, Upper Elkhorn No. 3, and Upper Elkhorn No. 2 beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 2,138 million short tons as of January I, 1932. Of this total, 1,956 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study, Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By C. M. Harrer

The location, features, qualities, and extent of iron occurrences and the associated resources--limestone and dolomite, bentonite, coal-lignite, petroleum and natural gas, power, and water--are evaluated. The results of pioneer beneficiation tests on South Dakota taconite are discussed. In addition, pertinent features of taconite development, cost factors, the Western and Central United States trade area and markets are reported. The State's production of iron ores until 1963 has been small and for purposes other than the manufacture of iron. This investigation disclosed the probability of large resources of taconite in Pennington and Lawrence Counties. The average iron content is 29 percent, and a 65-percent or better iron concentrate might be produced. Ample resources are available for mining and processing taconite. An investment of at least $26 million would be required for a plant capable of turning out 1 million tons of agglomerated iron concentrate per year. The feasibility of such an enterprise is indicated, but intensive investigation and research must be completed to justify such an investment,

Jan 1, 1966

By Oliver C. Fursman

This work was conducted to determine the feasibility of producing aluminum-silicon alloys in a pit-type, three-phase electric-arc furnace. Two carbon-lined furnaces were used in the tests. The power input ranged from 120 to 240 kw. in the small furnace and from 420 to 460 kw. in the large furnace. Energy consumption ranged from 5.3 to 11.5 kw.-hr. per pound of alloy produced and electrode consumption, from 240 to 510 pounds per ton of alloy produced. A wide range of crude aluminum-silicon alloys was produced by direct smelting of clays or similar aluminum silicate raw materials, using hogged fuel or wood chips as the major source of carbon in the furnace charge, and silicon of high grade was produced by smelting quartz. The aluminum content of the aluminum-silicon alloys ranged from 15 to 55 percent. Alloys produced from a white opaline-silicate clay were relatively free of iron, titanium, and other impurities. Those produced from western fire clays and kyanite, although richer in aluminum, contained considerable amounts of impurities. The purity of the alloys depended largely on the composition of the raw materials.

Jan 1, 1960

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004

By T. M. Romslo

The Lake Shore property, located in the early 1880's, contains copper-bearing deposits that have been developed by surface excavations, underground workings, and churn-drill holes. Operation of the property ended in 1929 with a total recorded production of 280,000 pounds of copper. The property is near the foot of the Slate Mountains, which are made up mainly of probably the Pinal formation of pre-Cambrian age. In the mine area there are a few outcrops of granite, which is exposed over a large area east of the property. Other outcropping rocks on the property are limestone, quartzite, and diabase. The limestone and quartzite probably are the Mescal and Troy formations of pre-Cambrian and Cambrian age, respectively. The predominant copper mineral is chrysocolla, a hydrous silicate that occurs mainly as fracture filling in bedded schist. It is also, the principal copper mineral in the shear zone at the schist-granite contact and in limestone southeast of the main workings. Investigation of the Lake Shore property by the Bureau of Mines included both topographic and geologic mapping, exploratory drilling, and metallurgical test work. One diamond-drill, hole and five churn-drill holes were completed for a total of 2,872.5 feet. Drilling started January 19 and was completed May 13, 1949.

Jan 1, 1950

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By Margaret R. Egan

A study of the combustion emission products of rigid ventilation ducting was completed by the U.S. Bureau of Mines. The ducting was composed of fiberglass-reinforced polyester resin. Four properties of the ducting were evaluated: (1) propensity to ignite, (2) smoke characteristics, (3) gas emissions, and (4) heat release. Particle sizes, obscuration, optical densities, and production constants for gas and smoke were also calculated. These results provide comprehensive data about the emission products, detectability, and relative hazards of fiberglass-reinforced plastic ducting and other mine combustibles under realistic fire conditions.

Jan 1, 1990

By Robert Lee Stahl

Comprehensive field tests were made by the Federal Bureau of Hines at the Conda open pit mine near Soda Springs, Idaho, to determine whether surface geophysical techniques could be used to detect and delineate faults in phosphate deposits. The tests included seismic refraction, magnetometry, electrical resistivity, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling was the most effective method for diagnosing faults. The method is quick, inexpensive, accurate, and can be easily used by mining company personnel to detect and delineate faults.

Jan 1, 1975

By Paul W. Johnson

A computer program for calculating capital and operating costs from material and energy requirements and equipment costs for use in preparing cost estimates for metallurgical process evaluations has been written by the Bureau of Mines' College Park process evaluation group. The program permits rapid recalculation of processing costs when changes of data or equipment are desired, and produces tables of capital and operating costs suitable for publication. Equipment cost summary tables for each process section end supplemental information for input-data checking is included in the computer printout. The program is written in Fortran IV except for several subroutines which are written in machine assembly language for the IBM 7094.3 With a few modifications, the program can be used on other computers.

Jan 1, 1969

By C. E. Julihn

In the fall of 1933 a new discovery of gold was made in the old Mojave mining district of California about 70 miles north of Los Angeles. It led to mining operations that have surpassed in their results all reasonable expectations and are of exceptional promise for the future. In less than 3 years, exploration has opened up a number of veins, from some of which a substantial amount of high-grade ore has been shipped, while a large tonnage of milling ore has been disclosed. Two mills, operating on ore averaging better than $12 a ton, will probably produce more than a million dollars worth of gold in 1936, and a considerable increase of their output in the following year is anticipated. While continuance of these operations for a number of years is already assured by ample reserves of ore, future discoveries of still other veins are reasonably possible, as occurrence of gold throughout the volcanic rocks of the district is widespread and the veins now being mined showed little to attract attention at the surface.

Jan 1, 1937

By Charles P. Lazzara

Concentration profiles of low-pressure, slightly lean CH4-02-Ar flames have been measured in situ for the following unstable species: oxygen atom, hydrogen atom, hydroxyl radical, methyl radical, and formyl radical. The observed maximum mole fractions were 2.0X10-2 for H, 1.1X10-2 for OH, and 0.8X10-2 for 0; the maxima occurred in the recombination zone. Methyl and formyl radicals have maximum mole fractions in the reaction zone of 2.2x10-3 and 6x10-5, respectively.

Jan 1, 1973

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

Estimate costs for projected uranium in-situ mining operations. Approach Develop a computer model and an associated data base which will allow users to supply data applicable to a specific mining site in order to estimate total capital and operating costs for a potential in-situ mining operation at the site. How the Model Works The model requires a minimal amount of input from the user. The data input must be known or estimated information about a potential in-situ mining operation. The user can also supply any additional project specifications. The computer model uses a process-engineering approach and determines through a discounted cash flow analysis the total capital and operating costs for the life of the project. This time-span measures from the start of the pilot-scale operation through to the site's restoration and reclamation. The model will determine the production cost per pound of material mined subject to the rate of return identified by the user. Conversely, it will also solve for the rate of return realized for the specific sales price per pound. [ ] Currently the model's data base can tai ns costs, rates, and specifications for Texas and Wyoming, the only states where commercial uranium in-situ mining is being conducted. However, this model can be used by anyone who is conducting in-situ leaching or who plans to leach uranium in-situ. At least part of any uranium deposit has a potential for in-situ mining.

Jan 1, 1982

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By J. B. Littlefield

[Ata. meeting of the Subcommi ttce on Chemical _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of Mnes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a reference method. 'I'ests ~ ere made aJ,so to aScer ain the effici ency of the recently developed midget i;npi gerS..! for collac ing lead dust. For comparative pur-poses, samples collected by tte large impinger wore included.]

Jan 1, 1938