Search Documents

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is

Jan 1, 1980

By J. E. Zeilinger

The technical feasibility of using energy from explosive ignitions of coal dust to pump water was .demonstrated in an exploratory investigation. Ignition of small amounts of pulverized coal that were dispersed in air over columns of water pumped up to 5.3 gallons of water per cycle when operated against a head of 30.75 feet. Water displacement was accomplished by either manual or automatic operation through a single cycle, and by automatic operation through a continuous series of cycles of I-minute duration. Operating through single cycles, slurries containing up to 3 pounds of coal and 4.6 gallons of water were also pumped. Possible uses of an efficient coal-fired pump would include pumping water for irrigation purposes, removing water from mines, transporting coal from mines in the form of a slurry, and pumping water to elevated reservoirs at electric powerplants so that it could be used to generate electricity during peak periods of demand.

Jan 1, 1966

By Wallace E. Anable

This investigation by the Bureau of Mines was conducted chiefly on Cuban serpentine nickeliferous ores to determine whether these materials would be amenable to direct carbothermic reduction in an electric furnace to produce a low-carbon ferro-nickel. The project was carried out as one of several under a Memorandum of Agreement between the Bureau of Mines and the General Services Administration (Contract GS-OO-B (D)-152l). Two ore samples were received for this investigation. One was a mixture of nickeliferous serpentine from the North Ocujal, South Ocujal, and San Juan claims of the Nicaro Nickel Co. The other sample was a mixture of material from the Ramona and the Lorna Mulo claims of the Cuban Nickel Co. Most of the ore from the Ocujal-San Juan deposits and about 40 percent of the sample from the Ramona-Lorna Mulo deposits were calcined before smelting. The remainder of the sample from the Ramona-Loma Mulo deposits was smelted after drying to about 8 percent moisture. An arc-resistance, selective-reduction smelting technique was employed in these tests. Either bagasse alone or a mixture of bagasse and coke was used for reductants. No flux was used in the furnace charges.

Jan 1, 1957

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By Lloyd A. Morley

The problems associated with the presence of organic materials and of water in explosion-proof enclosures used in high voltage, high capacity applications were examined through a literature search and theoretical reasoning. Information on volatilities is presented. The conclusion is reached that explosive pressures are significantly enhanced by inclusion of these materials.

Jan 1, 1976

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By B. W. Moore

The U.S. Bureau of Mines investigated the separation of heavy rare-earth elements (REE) in an ion-exchange process. An ion-exchange column consisting of two sections, a loading section and a separation section, provides high levels of REE loading and good REE separation with an expected processing cycle of less than a month, while current ion-exchange technology requires more than 5 months. A different resin is used in each section: sulfonic resin in the loading section and iminodiacetic resin in the separation section. The separation section is further divided into two segments: the first conditioned with NH4 and the second with acid. Erbium is loaded onto both segments of the separation column as a retaining ion. Bands of mixed REB eluting between separated bands of pure REB were recycled directly to the column. Without mixed-band recycle, over 80% of the REE eluted from the column was separated into fractions with 99% purity of each element; with such recycle, the percentage of separated elements can be increased to around 90%.

Jan 1, 2010

By Raja V. Ramani

The potential usefulness of reclaimed surface-mined land has received much attention recently. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Chinook Mine-West Field, located in western Indiana, has been studied. The Chinook Mine is presently operated by AMAX Coal Company and has been in continuous operation since 1928 under various ownership. The status of current reclamation and land use planning was reviewed. In addition, site planning principles were applied to the active mine area. This application included formation of a data base and development of postmining land use plan alternatives. Key factors affecting site potential realization for midwestern area mines have been identified along with suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 30 jurisdictions of the Western Hemisphere. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1970

By Oliver Bowles

In its geologic sense the term marble is applied to rocks consisting of crystallized grains of calcite or dolomite or a mixture of the two. Although limestone has the same chemical composition as marble it differs in that the component particles of calcium or magnesium car- bonates are granular and noncrystalline. In marble the crystals may be intimately intergrown, whereas limestone is an aggregation of unrelated particles cemented together into a solid mass. In its commercial sense the term marble has a much wider applica- tion. As susceptibility to polish is one of its chief commercial assets, all calcareous rocks capable of polish are classed as marbles. Lime- stones that show little crystalline structure may, if they take a good polish, be classed as marbles. Furthermore, serpentine rocks, even if they contain little calcium or magnesium carbonate, are classed as marbles, as they are commercial substitutes of true marbles.

Jan 1, 1916

By B. J. Scheiner

Extraction of silver from silver mill tailings by an electrolytic oxidation procedure was investigated by the Bureau of Mines. Various parameters affecting silver extraction, such as electrolysis time, particle size, and dissolution of the silver as the tetrachloro or cyanide complex, were studied at 30° C with an electrolyte concentration of 20 weight-percent sodium chloride. Resulting silver extractions ranged from 77 to 90 percent, depending on the tailings being treated. Concomitant extraction of mercury ranged between 90 and 95 percent. Power consumption was 52 to 90 kilowatt-hours per ton for the tailings investigated. Comparative experiments using direct cyanidation resulted in extraction of 46 to 82 percent of the silver and 20 percent of the mercury. Cyanide consumption ranged from 3.3 to 9.4 pounds per ton of tailings, depending on the tailings being treated. Silver and mercury were recovered from leach solutions by precipitation on iron powder, followed by conventional distillation and fire refining steps.

Jan 1, 1972

By R. V. Ramani

In this the available information friction factors and leakage report, on characteristics are reviewed and summarized. The use of Penn State Mine Ventilation Simulator (Volumes II and III of the Final Report) to analyze the sensitivity of the ventilation system to the changes in leakage and friction factors is discussed with examples. In simple ventilation systems, the results of changes in leakage and friction factors can be easily solved and explained by the laws of air-flow. In complex systems, with fixed quantity branches and multiple sections, the effect of changes in leakage and friction factors cannot be generalized. This study points out the importance of good input data for obtaining reliable information from computer analyses and demonstrates the application of simulators to analyze the effectiveness of ventilation systems. An extensive bibliography on friction factors, leakage characteristics and ventilation economics is included.

Jan 1, 1977

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By James H. Aase

[This study provides data on the physical and hydrological makeup of the ,t hakes waterway system and forecasts quantities, traffic patterns, and ping cost of prospective bulk mineral commerce projected to be transported it. Factors affecting the shipping cost of iron ore, bituminous coal, imestone were quantified and integrated into a computer program that can d to estimate costs under varying sets of conditions. Combined ship of iron ore, bituminous coal, and limestone in 1995 were estimated at million tons. The cost of operating the U.S. vessel fleet for trans-ng an indicated 80 percent of this traffic tonnage was projected to be $163. 5 million.]

Jan 1, 1970

By Corale L. Brierley

Accumulations of microorganisms in the in-situ leaching environment are believed responsible for plugging of the orebody and thus decreasing uranium extraction. To assess the contribution of microbial growth to this problem, packed columns of ore and core specimens were leached in the laboratory. Samples collected at four in-situ uranium mining operations revealed pseudomonads, xanthomonads, Bacillus sp. and Micrococcus sp. in numbers of 105 cfu/ml. These microorganisms, inoculated into simulated leaching conditions, decreased permeability in two uranium ores by one order of magnitude in 20 days. Hydrogen peroxide (0.2 g/l) alleviated microbial plugging in the laboratory. Periodic injection of hydrogen peroxide through the production well into the orebody may reduce microbial plugging problems in the field.

Jan 1, 1982

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures area discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of mining modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mine is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By G. C. Price

This study traces the development of the bucket-wheel excavator, points out the differences in the German- and American-type wheels, and gives the major design criteria and the advantages and disadvantages of bucket-wheel operations. A computer program, written in FORTRAN IV for use with an IBM 360 computer, simulates the operation of the digging components of a bucket-wheel excavator. By supplying certain mining dimensions, soil characteristics, and machine design specifications, this program will print out a time study of the various components of an operation, power calculations for the operation, and production data. This program, when combined with a truck, belt, or rail program, should be helpful in planning a complete mining system In material suitable for a bucket-wheel excavator operation.

Jan 1, 1973