Search Documents

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

By J. E. Dooley

A mass spectral scheme of analysis was devised which can be used to identify individually a single compound from a larger group of similar compounds. Mass spectra for 32 alkyl aryl sulfides are provided for future reference work, and analytical correlations used in producing the analytical scheme are discussed. Some of the correlations show that base peaks are either the same mass as the parent peaks or may be derived from cleavage alpha to the sulfur atom with migration of one hydrogen to the sulfur atom. Other spectral consistencies provide means of separating ortho-, meta-, and paratolyl arrangements in an overall analytical scheme. Determinations of chain lengths and separation of isomeric species are also discussed.

Jan 1, 1972

By R. R. Sayers

Carbon monoxide poisoning, as usually encountered, is an acute condition resulting from breathing atmospheres containing that gas. It is characterized clinically by headache, dizziness, weakness in the legs, increased respiration at first which later becomes irregular and depressed, collapse, unconciousness, and death; anatomically it is characterized by temporary changes in the red blood cells due to the combination of carbon monoxide with hemoglobin, and, in prolonged severe exposures, degenerative changes in various tissues of the body, especially those of the central nervous system. No race or nationality is immune or has a, special tolerance for carbon monoxide. From data at hand, it is known that both sexes are about equally susceptible. All ages are affected, but small percentages seem to have a more deleterious effect upon young animals and this is possibly true of children. Exercise, high temperature and humidity, and low oxygen content of en atmosphere increase the degree of poisoning for a certain concentration of carbon monoxide. Anything that lowers the physical fitness of a man, such as illness, overwork, or excesses of any kind, exaggerates the effects. More cases of poisoning from carbon monoxide occur in coal mines in the cold months of the year, because explosions take place more frequently during that period, also in homes where gas is used for beating purposes, and in garages from accumulation of automobile exhaust gases due to poor ventilation.

Jan 1, 1923

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

Objective: The Roof Monitoring Safety System (RMSS) provides a first step in roof behavior awareness. By understanding and measuring roof movement in an underground mine, the potential for injuries or fatalities to mine workers from fall of ground can be lessened. Also, officials at an underground mine with a history of data on roof movement are better prepared to make a decision on remedial actions if falls of ground become a problem. The RMSS provides a safer, simple, and inexpensive means for measuring roof movement.

Aug 1, 1998

By H. Nelisse, S. K. Patra, A. Natani, S. Rakheja

The current laboratory methods for assessing the vibration attenuation performance of seats involve repetitive trials with a number of human occupants, and raise certain ethical concerns. Moreover, the measurements with human subjects yield considerable variability in the data. Alternatively, several anthropodynamic manikins have been developed for effective assessments of the coupled seat occupant system [1]. The effectiveness of a manikin in predicting the response of a coupled seat-occupant system lies in its ability to reproduce the biodynamic response of the seated human body in terms of force-motion relationship at the body-seat interface, such as apparent mass (APMS). A number of prototype manikins have thus been developed on the basis of biodynamic characteristics of vertical vibration-exposed seated occupants of different body masses in the vicinity of 5th, 50th and 95th percentile male population. This study concerns with the analysis of a passive prototype manikin to enhance its ability to reproduce the idealized APMS response characteristics of the vibration-exposed seated human subjects defined in ISO-5982[2] for mean body masses of 55, 75 and 98 kg. Methods The APMS responses of a prototype anthropodynamic passive manikin were thoroughly characterized in the laboratory under different excitations and body mass configurations. The manikin was designed with sufficient flexibility to configure mechanical-equivalent models corresponding to seated body masses of 55, 75 and 98 kg, by adding/removing specified masses and springs (Fig. 1). The manikin, configured for a specific body mass, was positioned on a rigid seat without a backrest, which was fixed to the force platform of a whole-body vertical vibration simulator. The simulator was programmed to synthesize random vertical vibration with flat acceleration power spectrum in the 0.4-20 Hz frequency range with two different magnitudes: 1 and 2 m/s2 overall rms acceleration. The total static and dynamic forces of the manikin to and the seat were measured using the force platform, while a single axis accelerometer was installed on the seat pan to measure acceleration due to vertical excitation. The measured data was appropriately corrected for the rigid seat inertia force, and the apparent mass [ ]

Jan 6, 2006

By Brian G. White

The Coeur d'Alene Mining District of northern Idaho is remarkable for its number of large ore bodies and for the amount of its historical production of lead, zinc and silver (Fig. 1). Since veins were first discovered in 1884, more than 127 Mt (140 million st) of ore have been produced from narrow, high-grade veins. Mining continues at the Lucky Friday, Galena and Sunshine mines (Fig. 2). All have been in production for decades. At these mines, more efficient mining and exploration techniques have reduced costs while adding significant new reserves. Even the old Bunker Hill Mine, where ore was first found in 1875, continues operation on a limited basis, partly involving production of world-class pyromorphite specimens. Until recently, the Coeur Mine was also a profitable silver producer. Other large producers have included the Star-Morning, Hecla, Page, Standard-Mammoth, Hercules and Gold Hunter mines (Fig. 2). The first deposits were discovered by prospectors who spilled over from the Murray gold mining district, 24 km (15 miles) to the north. The Bunker Hill Mine was founded the year after the first veins were discovered. Bunker Hill has now operated for more than 100 years. Production includes 2.3 Mt (2.6 million st) of lead, 1.1 Mt (1.2 million st) of zinc and 4.1 kt (132 million oz) of silver. Total district production through 1996 (Springer, 1997) amounted to 7.3 Mt (8.1 million st) of lead, 3 Mt (3.3 million st) of zinc, and 34.5 kt (1.109 billion oz) of silver. This record establishes the district as the largest recorded producer of silver in the world, while also yielding major quantities of lead and zinc. Only Potosi, Bolivia, may have produced more silver, although records are unclear. Despite the district's longevity, historic production and current activity, the published literature on the district lags behind with regard to recent concepts of district geology. The most recent comprehensive US Geological Survey (USGS) bulletins (Hobbs et al., 1965; Fryklund, 1964) are dated. Much research in the last half century has been short-lived or geographically restricted because the district is large and its geology is complex - and even this research tends to remain unpublished. Thus, it has been difficult for in- [ ]

By B. L. Razzaboni, P. Bolsaitis

"The formation of reactive oxygen species resulting from the interaction of silica dust particles with red blood cell membranes was investigated; particularly, the effect of surface hydroxyl (silanol) group concentration on the rate of formation of such reactive oxygen species was investigated. The rate of formation was measured indirectly through the effect of catalase, a hemoprotein peroxidase, on silica-induced hemolysis. It was found that the addition of exogenous catalase to erythrocytes markedly reduces the hemolysis caused by silica particles. Furthermore, the amount of catalase required for deactivation of silica per unit area of particle surface is lower for fumed silica particles and calcined crystalline particles than for uncalcined, crystalline silica, suggesting a correlation between the concentration of OH groups at the silica particle surface and its potential for generation of H2O 2• The addition of albumin, a copper chelator, also decreases hemolysis. These results suggest that the hemolysis caused by silica particles is at least partly related to the formation of H2O2 at the particle surface and its subsequent reaction with Cu+ ions. The relationship between the concentration of surface silanol groups on the silica surface and the amount of catalase required to decrease hemolysis may also provide a method for testing potential fibrogenicity of respirable dusts. IntroductionReactive hydroxyl groups on silica surfaces are known to be cytotoxic and are believed to play a major role in silicosis (1-9). It has been proposed that this cytotoxicity results from hydrogen bonding to cell membranes and a resulting increase in membrane fluidity and permeability (4). Surface hydroxyl groups on silica surfaces have also been shown to interact with carbonyl oxygens in cell membranes (1,5). An extensive study by Nolan et al. (6) of the relationship between the negative surface charge resulting from ionized silanol groups and the hemolytic activity of crystalline a-quartz (Min-U-Sil) has shown a positive correlation between hemolytic activity and the surface concentration of silanol groups. These authors demonstrated that the hydrogen bonding of polyvinyl-N-oxide (PVPNO) with silanol groups, as well as the bonding of metal cations to the ionized sm- groups, results in significant decreases in hemolytic activity. Furthermore, it has been found that the complete removal of surface hydroxyl groups from the surface of respirable silica particles nearly eliminates the hemolytic potential of silica (7), suggesting that hydroxyl groups might be involved in other cytotoxic processes associated with silica-induced lung injury. Reactive oxygen species have been .implicated in cellular damage caused by respirable silica particles. Evidence for the presence .of oxygen radical species (02, OH°, H2O2) generated by silica, especially on freshly formed surfaces, has been produced by various investigators. Kalbanev et al. (8) detected H2O 2 in aqueous suspensions of quartz. Electron spin resonance and spin trapping by Shi et al. (9) confirmed the presence of OH"" radicals in aqueous suspensions of quartz, and Gulumian and van Wyk (10) suggested that both glass and quartz produce hydroxyl radicals in the presence of H2O 2 • Gabor et al. (11) detected the presence of malondialdehydereactive lipid peroxides (i.e., lipid-0°) in cultures of macrophages and respirable silica particles using the thiobarbituric acid (TBA) reaction test. Will (12), however, reported that iron enhances the TBA value of peroxidized lipids, and Scheulen and Kappus (19) found that catalase augmented malondialdehyde formation, thereby increasing the TBA values."

Jan 1, 1990

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of-combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were conducted in a 1 80 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.13, and 0.06 m/s were determined at 30.60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

By A. W. Ambrose

"Introduction.Oil-field operations have often been carried on under great stress and haste, in which the prime purpose has been to put the wells down rapidly as possible, without regard to a few of the various factors affecting cost. In such fields as Burkurnett, Texas, where the well locations are town lots and other small tracts, the operator was concerned primarily with in drilling. In such cases a few thousand dollars more or less in the cost of a well not considered. We are reaching a time, however, when our reserves a,more definitely outlined and properties are being along more economic lines. Operators are becoming more concerned with the actual cost of this work, and are gradually learning that fuel consumption can be reduced in drilling and producing without delaying the speed of drilling, and in the case of production, it will greatly reduce the unit cost per barrel of production.Types of Field Boilers.In the oil fields there are in general two types of boilers; those which are used for drilling wells and are of a more or less portable character, and those established later in a more permanent form and serve for the purpose,of generating steam for producing the oil. As a rule, the latter type of boilers are larger than those of the drilling type. Usually, little care is given to the installation of drilling boilers; particularly in attempting to set them up in such a way as to avoid waste in of fuel. Because of the temporary nature of these installations there may be some justification for not giving them more,attention in this resend, but it is believed that a few precautions could be taken that would amply repay the cost and trouble taken. In connection with the boiler plants that are afterwards established, when a few producing wells have been,brought in with a life of two to ten years and probably longer, much care to the boiler-plant construction and to the installation of recording instruments which will assist in operating the plant at minimum cost."

Nov 1, 1920

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (EM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR) , and 5) Amplitude Probability Distributions (APD) . These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

Develop hydrometallurgical or pyrometallurgical recycling methods to recover valuable rare-earth compounds from various forms of NdFeB magnet scrap. Background The U.S. Bureau of Mines (USBM) has developed technology to treat and recycle a variety of wastes containing valuable and strategic metals. As part of this effort, the USBM developed a process to separate neodymium and other valuable rare earths from iron in NdFeB magnet scrap (fig. 1). Since this scrap typically contains nearly 30 weight percent neodymium and since the demand for neodymium is constantly increasing, cost-effective methods for scrap treatment could have a significant impact on industrial expenditure and materials supply in the expanding area of magnet manufacture. Approach A hydromctallurgical, H2SO4 dissolution-precipitation process provided the most effective treatment for separating rare earths from bulk NdFcB magnet scrap (fig. 2). Precipitation of neodymium-alkali sulfate double salt proved advantageous over direct precipitation of fluoride or oxalate products. This double salt is easily converted to a variety of useful rare-earth compounds, which eliminates many of the materials-handling and economic problems inherent with direct precipitation. Following rare-earth precipitation, dissolved iron was removed from the acid leach solution by precipitation as a jarosite.

Jan 1, 1993

By P. W. Jeran, S. J. Pepperney, M. C. Irani, F. F. Kopsch

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1980

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method's potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By Scott W. Hazen

This report describes the design, analysis, and results of a special experimental mine-sampling project conducted as part of the Bureau of Mines continuing program on sample-methods research. The experimental project was conducted at the Bureau?s Denver Mining Research Center and at the Climax molybdenum mine within the framework of a cooperative research agreement between the Bureau and Climax Molybdenum Co., Division of American Metals-Climax, Inc. The primary objective of the project was to investigate the interrelation-ship between sample volume, number of samples, the standard deviation of an assay distribution, and the precision required for an estimate of grade of ore, and to develop this interrelationship into a relatively simple method of application for use in mine sampling.

Jan 1, 1962

By G. L. Cook

The design of a dual-inlet system for a Consolidated model 21-103C mass spectrometer is described in detail. The system permits both high-mass and low-mass samples to be run by using a single instrument. The difficulties of using a single instrument for both purposes are given and a method of minimizing these difficulties through the use of the present design is discussed, After examining the experience of five years of use, the conclusions are that the bimodal operation is practical and the low-mass analyses had nearly the same precision as before the modifications to the instrument were made. In 1951, O'Neal and Wier.5/ published the first description of the modifications made to a mass spectrometer so that the spectra of hydrocarbons with molecular weights up to 600 could be obtained. Further discussion of the equipment of O'Neal appeared in 1953.6/ Also, Brown, Melpolder, and Young7/ described a parallel inlet system designed to reduce sorption effects at room temperature.

Jan 1, 1960

By Arcy P., D&apos Banister

Several gold-antimony geochemical anomalies were outlined near Stibnite, Idaho, using the humus sampling technique. Several hundred reconnaissance humus samples were collected and analyzed by a combination fire-assay atomic absorption method. The results partially outlined several gold-antimony anomalies and are very encouraging for further work in this part of Idaho.

Jan 1, 1970

By J. R. Allsup

In cooperation with the Division of Advanced Automotive Power Systems Development, Environmental Protection Agency, the Bureau of Mines studied a conventional spark-ignition engine as a prime mover for use in a hybrid system. The study involved both steady-state and transient engine operation with ignition timing, air-fuel ratio, exhaust gas recirculation, oxidizing type catalytic converters, engine speed, and power output as variables. Data were obtained from two 1971 model 350-cubic-inch-displacement engines mounted on engine dynamometer stands. When the hybrid engine was operated with an oxidizing catalyst at power output levels required for a 4,000-lb curb weight hybrid vehicle, carbon monoxide and hydrocarbon emissions could be reduced to approximately 2.0 grams and 0.3 gram per brake horsepower-hour, respectively. With exhaust gas recirculation, oxides of nitrogen emission levels could be reduced to approximately 1.2 grams per brake horsepower-hour.

Jan 1, 1974